Converting 3 plate Clutch assembly into 4 and 5 plate

[@asefsha8378]

Excellent! This is what I was thinking of doing myself.... You spared me a lot of time. Thanks for sharing...

[@antoniovarghese]

Hi , I do watch all your videos,so I could do my bullet maintenance myself. I changed engine oil,oil filter,gear oil, clutch side oil,fork oil and done all necessary maintenance . Thanks.

[@gaganp619]

Do we need to change the clutch cover if we want to change the 3 plate clutch assembly to 4 or 5 plate clutch assembly in old std350 ?

[@ECFixeljin]

For 4 plate there is not need to change. But for 5 plate you need to change clutch cover,clutch center and clutch sprocket

[@dudesandtools]

Hi... I own a diesel bullet and since the compression ratio is higher ,my stock clutch setup slips when i kick start it. I have tried adjusting the clutch play and also adding washers to spring to increase the force but to no vain...i am planning to do this mod which might help or i might have to get stiffer clutch springs....have you come across similar issues anywhere?...and what do you suggest i do? Thank you

[@ECFixeljin]

kzbin.info/www/bejne/nna2ioGQnr-kmJI Check this video and make sure whether you have enough (3-4mm) clutch play.

[@beatlesadeye4912]

What is the name of 4 clutch plate assembly. Which model to be used in place of 3 clutch model bullet

[@beatlesadeye4912]

I mean which model bullet we will have to buy?

[@reaperbot5610]

I have 4 speed clutch in my old model bullet... Can i use 500 cc UCE model clutch assembly ?

[@sheringeorgethomas2078]

Very useful bro what is the benefit to change 3 piece in to 5 piece in old royal enfield is the performance is increase or not

[@abdulgafoor-ds2oe]

Very informative sir

[@mariaviagulam4111]

Excellent one....

[@eldojoseph563]

For slow speed rides in 4th gear, which one you prefer 3 plate or 4. especially in high weighted crank models ?

[@ayushmannmishra8]

3plate

[@Thevillageheadmaster]

Can you kindly mention the brand name of the four clutch plate kit?(cannot make out from the audio)

[@ECFixeljin]

Endurance friction plates

[@Thevillageheadmaster]

Thank you. Appreciate it much.

[@Thevillageheadmaster]

After watching your video I searched the net and recently purchased an endurance 4 clutch plate but was surprised to receive an enfield company clutch plate(part no.597383). I am wondering are they what you were referring to or did I purchase wrong one.If I have got a wrong one,could you kindly suggest a site where I can purchase the endurance brand clutch plate?

[@asefsha8378]

Hello.... Can you please let me know whether how to do servicing of contact breaker unit bearing and shaft. I want to change the bearing. Kindly make video or explain how to remove bearing and shaft in contact breaker distributor unit. It would be of great help to all the bullet lovers. P.S. I could not find this information anywhere on the internet or in Pete Snidal's book.

[@rahuljeet5281]

3 plate clutch creat any problem???

[@drvineeth.viswanath6206]

Very informative and interesting video 👌👍🤘💗 what are the advantages and disadvantages of replacing 350 clutch plates with 500 clutch plates. Please do answer.

[@honeyy7495]

Can we convert 4 plate clutch into 3 by removing one plate ?

[@ECFixeljin]

No. Since the clutch center height is greater than that of the 3-plate clutch assembly, we won’t get enough tension from the spring.

[@honeyy7495]

@@ECFixeljin so how i can ?

[@ariesha2012]

I need help with my bullets ci engine kick, it doesn't engage hence bike does not start. How can I contact you and share the video of my bike?

[@ECFixeljin]

It maybe due to two reasons. 1. Wear out clutch ( replace it with new clutch plates) 2. Faulty clutch play adjustment ( check this video:kzbin.info/www/bejne/nna2ioGQnr-kmJI)

[@ariesha2012]

@@ECFixeljin Thank you for your response and suggestion. The 2nd point did help as the primary clutch plate was fixed the wrong way also the main issue was the kick pawl as it was broken and had to be replaced. Now the bike is fine and this also fixed one of my prolonged issue.

[@ayushmannmishra8]

Sir which clutch is best for old model bullet 1973 3plates clutch or 4 plate clutch or 5 plate which one give us more power and pickup?

[@ECFixeljin]

4 plate is good

[@ayushmannmishra8]

@@ECFixeljin Sir it gives good power in mountains too?

[@ayushmannmishra8]

Sir when I'm riding alone it give perfect power and pickup but when I ride with passenger it's performance slightly decreased what should I do for this fault?

[@adityadeshmukh9131]

@@ECFixeljin I have the same problem with my bike please reply I want to increase in performance of my bike what should I do, please reply

[@ayushmannmishra8]

@@adityadeshmukh9131 brother did you get any solution?

[@subhint7200]

Do we need to apply greese while installing clutch plate in old bullet Which type of oil is suitable for clutch

[@ECFixeljin]

No. Dip the clutch plates in oil before installing. Use 20w40 oil

[@dipeshmondal267]

Sir plz make a video on magnet coil of 3 wire

[@jayam258]

Hi.... My bullet kicker strengthening what do to any suggestions

[@king000775]

Bro I think we need to change the clutch case cover when we increase the plates, am I right?

[@anandbhardwaj7590]

Yes

[@ECFixeljin]

For 4 plate there is not need to change. But for 5 plate you need to change clutch cover,clutch center and clutch sprocket

[@ITZ_PARTHIB_BITCHESS]

Hello sir can you kindly give me the part code of complete 3 plate clutch assembly

[@tanveeraziz5420]

Hi I have installed 5 clutch plates of machismo 500 (endurance) in my std 350. It runs smooth and a slightly increase of power is there. Once i put the motorcycle on kick stand while engine running (although i never do it as it starts burning oil in old models) there is sound from clutch like it is touching the cover when you put it bend on kick stand. Although it never sounds while it is straight. Seems like it slips a bit and touches the cover but normally it doesn't. It's fine. What should be the problem?

[@ECFixeljin]

Check properly it may come from the gear box.

[@tanveeraziz5420]

No, its from the clutch. Yeah gear does sound when it's not in full neutral. I always put in full neutral b/w 1&2.

[@DineshBaluplus]

My 1982 bullet is always jerky while driving, What would be the problem

[@ECFixeljin]

Due to timing issue. Retard the CB point.

[@swaramdigitalsoundsystem]

Bro in Enfield tarus(company diesel bullet) howmany plates are there 4 or 5 ???

[@JOJO-ub6jv]

Does classic 500 clutch assembly suite for this , Or is it available in the market theat the 500clutch plate you have showed

[@ECFixeljin]

No. It's available in the market

[@mahidharsai1590]

Can we use 5 plate clutch assembly in Electra 5s self start with out changing clutch cover

[@clementsebastian1977]

Bro, What will happen if we increase the the plates?

[@pritamshet7755]

Sir, i have 2000 model bullet, oil is leaking in heavy amount from drive shaft even changed oil seal but also its not stopping. Oil is leaking only when bike is started. Please help....

[@ECFixeljin]

Check properly it may be through breather

[@pritamshet7755]

@@ECFixeljin no i have opened clutch case its coming from bearing,crankshaft changed oil seal also but also it is coming in heavy quantity while engine is started, it doesn't come when engine is off

[@ECFixeljin]

Oil may leaking from oil chamber to Crank chamber. Check it out

[@pritamshet7755]

@@ECFixeljin ok

[@anaswarpsubi]

Hello bro.. When I change 3 plate to 4 should I change clutch rod pad?

[@anaswarpsubi]

Please rply

[@ECFixeljin]

No

[@anaswarpsubi]

@@ECFixeljin thanks

[@vu2yuu]

super very informative, will change by myself now

[@pandakarthik9846]

what makes it difference brother?

[@ECFixeljin]

It's pulling power is high but the Impact on clutch centre is less when compared to 3 plate.

[@pandakarthik9846]

@@ECFixeljin thanks

[@raosahab8382]

Thanks for sharing.

[@kdeep1690]

I have elecra CI 4 gear. Can i put 4 plates? Or should i change clutch assembly to 500cc

[@ECFixeljin]

Yes without any modifications you can convert it.

[@kdeep1690]

@@ECFixeljin I opened it and found it already has 4 plates. Now if I start with inserting clutch plate as first plate and then plain plate and so on..... And finally a clutch plate and then clutch cover .... This way I can put 5 clutch plates and 4 plain plates. Would this set up work??? Ofcourse this needs a little extension in clutch push rod

[@nirmalbabu7799]

nice video bro

[@rajsingh6206]

You should give part numbers of all the components.

[@ECFixeljin]

Soon I'll update it

[@TarunSingh-uq1kv]

When

[@shyamraja4204]

For slow speed in 4th gear below 40kmph how many clutch plate to use

[@ECFixeljin]

Clutch assembly with rubber plate will comparatively have less jerking effect.

[@honeyy7495]

@@ECFixeljinrubber plate mean?

[@manojshenoy3513]

Hi EC fix, I tried mounting 4 plate(ENDURANCE TYPE) on a 3 plate assembly as shown.. but every time I engage clutch the 4th steel plate pops/slips out from the clutch bell....

[@ECFixeljin]

4th plate should be inverted one

[@manojshenoy3513]

@@ECFixeljin yes its inverted one but while engaging clutch bell falls short....

[@ECFixeljin]

Can you tell me the order which u place the plane plate

[@manojshenoy3513]

@@ECFixeljin 2nd and 3rd are plain plates 1st and 4th invert..

[@ECFixeljin]

Can you take the pic and send it to my WhatsApp

[@ayushmannmishra8]

Sir which clutch has more pulling power?

[@ECFixeljin]

Endurance friction plates

[@ayushmannmishra8]

@@ECFixeljin sir I'm asking about which clutch has more pulling power 3 plates or 4 plates in heavycrank model

[@ECFixeljin]

@@ayushmannmishra8 4 plate

[@ayushmannmishra8]

@@ECFixeljin but my bike is pulling very heavy I have endurance 4 plate clutch

[@goldenbugnangel]

@@ayushmannmishra8On a 3 plate clutch bullet we can go much slower in 4 th gear.but it is not possible to go with a 4 plate.

[@abhishekrath653]

Sir 5 plate install in 4 plate assembly it is possible

[@vintage.vibees]

What is the performance when we use endurance clutch plate

[@ECFixeljin]

Improvement in pickup and cause less damage in clutch centre

[@சத்தியசிவன்]

Super i can modified based upon your post

[@arjunseelam9117]

Super ❤️

[@nagavenkata100]

After converting my 1983 RE from 3 plate to 4 plates..... The pickup has been drastically decreased...... So again I swapped 4 plates to 3 plates set....

[@ECFixeljin]

Did you feel heat in primary chain case?

[@nagavenkata100]

@@ECFixeljin Nope....

[@ayushmannmishra8]

@@nagavenkata100 kesa pick-up kam hua tha bro?

[@sarkop848]

​@@ayushmannmishra8instant pickup decrease

[@rashmilawson5074]

🙏🙏🙏🙏

[@sheringeorgethomas2078]

Very useful bro what is the benefit to change 3 piece in to 5 piece in old royal enfield is the performance is increase or not

[@sheringeorgethomas2078]

Very useful bro what is the benefit to change 3 piece in to 5 piece in old royal enfield is the performance is increase or not