I have a 2001 Columbia par car electric. Both rear wheel bearings finally failed. I found your video and replaced the bearings in no time doing it the same way you did. The adjustable wrench technique to remove bearings from axle was superb. Thank you.
@cpfans904 жыл бұрын
You don't need a puller. All you had to do was turn your brake drum around backwards and put the nut on it and hit the drum and it will pull the axle out....
@gwernette59712 жыл бұрын
Thank you for this video. I have had no previous experience with golf cart maintenance and this was extremely helpful. My family had purchased a used golf cart, the rear wheel had been making some grinding noise from day one
@frankcastle52942 жыл бұрын
Tell ya something Bud...this is a great vid. Not everyone has presses and seal installation tools and such at home. But we want to do these sort of repairs ourselves. You showed everyone how a bit of home ingenuity can save them a ton of cash. Thanks very much.
@mikecourville95954 жыл бұрын
Thanks so much for your video, I just finished replacing both rear axles, bearings & seals, and hubs on my golf cart.....couldn’t have done it without your procedure, my cart’s like new now and doesn’t make a sound!
@atlhawk71835 жыл бұрын
Great video, rock that DIY !!!
@o_______o93074 жыл бұрын
very clever idea to take bearing off ^^ thanks for the great vid cheers
@PacTel543212 жыл бұрын
Excellent instructions. Thank you
@nola26354 жыл бұрын
Was there a pin or locking clip in the differential holding the axle in or was it just pressed in?
@ciott1am4 жыл бұрын
What was the bearing kit part number you purchased? Also was this the outer bearing or inner bearing? Assuming its the outer?
@evilgti20004 жыл бұрын
Dude has a slide hammer but not a $7 snap ring pliers 🤣
@gwernette59712 жыл бұрын
I rented a slide hammer from my local auto parts, but it was not needed.
@David255222 жыл бұрын
The good pair of snap ring pliers cost more than $7 pal. I will say that I wouldn’t do the job without having them. Having a pair of snap ring pliers is a good investment.
@kellynieves74242 жыл бұрын
Do you need to add any fluid to the axel shaft? If so, what? How? Great Vid! Thank you.
@jp74893 жыл бұрын
Thanks for the vid👍
@kenbrown44252 жыл бұрын
I laughed when you skipped trying to get the wheel hub off straight to showing the axle shaft .
@Austin-xk6sm2 жыл бұрын
probably had the brake pedal locked down
@vinces89743 жыл бұрын
Very helpful thank you
@marktejero42273 жыл бұрын
Where did you get the adapter for the slide hammer
@chrispedersen5480 Жыл бұрын
Quick question, after getting the new bearing on axle, does bearing spin jerky, mine is not smooth after installing, not sure if these aren’t the right bearings or if it’s normal for them to feel jerky and not spin smoothly?
@williampage18424 жыл бұрын
Do you recall the part numbers for that kit
@macknumber9 Жыл бұрын
I was hearing squeaking so i thouhht it was bearing...removed everytbing and bearing just fell off...bearing is fine...axle shaft wore down so inner race of bearing isnt riding tight to the axle....can i get a replacement sleeve or do i just need to try and find another axle?
@edwardramirez96175 жыл бұрын
very good info. need to find a puller..
@johngosselin72323 жыл бұрын
Thank you for the video I just changed it out on txt.
@marktejero42275 жыл бұрын
Did you do both sides?
@alexmozingo89723 жыл бұрын
Hey what sound did it start making before it got replaced?
@SmokinDogg682 жыл бұрын
You will hear a screeching or a grinding or popping sound. In general those kind of sounds. my bearings in sort exploded.
@dutchleussink1563 жыл бұрын
Thanks
@stinkyvonfishstix41965 жыл бұрын
you should never hit a new bearing like this and you never "drive it in" by the outside race. always use the inner race when pressing your bearing in(depending on the bearing) bearing in a hub like the front you press in using the outside race
@tahcogunworks4 жыл бұрын
Exactly. I was cringing when he was pounding on the outer race.
@JT-xf7ti2 жыл бұрын
Right. I bet the new bearing is junk by now. By no means was it the right method but he could have just tightened the adjustable a little. And his interpretation of the “old School” way is apparently just the wrong way that may get the job done.
@ronb13596 ай бұрын
Could of heated the bearing a bit and it would of dropped right on
@thomasgregory894111 ай бұрын
good thanks
@gary304274 жыл бұрын
I just use the brake drum to press the new bearings on
@worleysalls51592 жыл бұрын
How do you do that ?? Won't it strip the threads on axle? That's alot of force
@timcrofford41085 жыл бұрын
Snap ring pliers are pretty cheap......
@TheQuietfiresnag3 жыл бұрын
I mean isn't the old school way of doing it using the right tool for the job. I appreciate innovative work arounds for proprietary tools, but snap ring pliers are cheap and worth using.
@gwernette59712 жыл бұрын
You don't want to go with the cheap snap ring pliers because these inner snap rings are larger diameter, and require a lot of tension
@andrewbrown88723 жыл бұрын
Just put the shaft in the freezer
@kdrapertrucker4 жыл бұрын
He didn't pack the bearings.
@arianaxgrxndehappynewyear31993 жыл бұрын
bearings are sealed no need to pack
@williamhebert325 жыл бұрын
Where did you get the adapter for the slide hammer
@stinkyvonfishstix41965 жыл бұрын
any auto part store will have a axle puller. that is what it is called