Elegoo Neptune 3 Pro/Plus/Max Voron Stealthburner Install for Multi Material.

This is just a short video on how to install the stealthburner on the Neptune 3 Series printers.
Mount: www.printables...
Required Hardware:
7x M3 Brass Heatset Inserts: amzn.to/496K7zf
7x M3x8mm Cap Heat Screws: amzn.to/4bwOsgQ
Don't forget to check out our amazing filament sponsor Filamentive at www.filamentiv...

[@GhostWolf188]

Hey there MakerMylo ive installed klipper on a pi for my neptune 3 pro and was looking at doing exactly what your doing can you tell me which kit you picked up with the cutter ? and great videos man keep it up :)

[@luisarevalo4645]

Hey, IO just finished installing Klipper on my neptune 3 plusm and I was thinking exactly to put a stealthBurner, I'm going to start binging your content. see you in a while

[@victordelephimne9873]

Thanks for the great content, I am in the process of building out one of my 4 max's with your mods. Working on the ERCF now and the SBurner as well. I already did the liner rail and z belt drive upgrade.

[@marcelm7711]

which hotend are you using?ìs your printer using klipper? and are you using the original motherboard from the printer? i also had a Stealthburner and it destroyed my Printerboard, i was using an Rapido hotend

[@makermylo]

@@marcelm7711 uh oh, I used the original board with Klipper and a BTT Pad7. The hotend was a Bambu Lab X1C .4mm. I ultimately put it back to stock and donated it as i wasn’t using it anymore since buying the Voron machines.

[@chopimageib-prod9080]

Bonjour, vous utiliser quel slicer ? c'est possible de nous partager le profile utiliser s'il vous plait ? je vous remercie d'avance de votre gentillesse

[@ligaila2905]

hi, do you have a link to the assembly and components?

[@yt-sweety]

Sorry maybe for stupid question, but can I wire up stealthburner via cunbus to mobo of stock Neptune 4/4pro? Or I need to upgrade motherboard or buy additional board. I also have a cartographer 3d probe(beacon 3d clone), but it connected with usb, because I don't know how and where I need connect canbus. So it will be 2 canbuses as I undersood(idk). Thank you!

[@makermylo]

You could run the BTT SB2209 SB2040 board the same as mine via Canbus but you may need a BTT U2C module, im unsure if the stock N4 board provides CAN. with a U2C however you could. You could then connect the Carto to the CAN network or directly to the SB board.

[@Final_Layer_3D]

Are your fans in the toolhead 24v? I have a few 24v blower fans I hope will work or order the correct one when I order the axial fan. I'm currently running Klipper on a BTT Pi and ordered the EBB SB2209/SB2240 and CAN adapter for the Pi.

[@makermylo]

Yeah although it doesn’t matter which you use as the EBB has a built in buck and you can simply set the voltage for the fans using a jumper on the board :)

[@Final_Layer_3D]

@@makermylo perfect! Thank you!

[@FrankFitzgeraldBatin]

is this possible for neptune 4 pro stock motherboard?

[@makermylo]

It is indeed yes, the stock mainboard runs Klipper :)

[@samstone86]

so you have a different board for this, right?

[@makermylo]

I run the BTT Canbus controller, and NOW i run a BTT Mainboard however you can do all of this on the factory board as the BTT Toolhead plugs directly into your Klipper Host (Raspberry Pi etc).

[@kadirbaydemir2957]

Hello. I'm not very experienced. I want to buy Neptune 3 Max or plus, but I want it to be fast. If I install a Neptune 4 motherboard, will it be cost effective and will the speed be the same as Neptune 4?

[@makermylo]

I'm sure you could make it work but i dont think the 4 board would "Fit" into the 3 shell, im unsure on mounting holes etc, however electronically i don't see any reason why it wouldn't work, most of the other hardware is essentially the same.

[@kadirbaydemir2957]

@@makermylo I contacted Elegoo. Even though Elegoo says the engines are not the same, I think the engines are the same. Have you used Neptune 3 and 4?

[@kadirbaydemir2957]

@@makermylo New holes can be drilled for mounting, I think it is no problem. It is enough to get the speed and acceleration I want from Neptune 3.

[@makermylo]

​@@kadirbaydemir2957 They do tend to say that about everything, as they can't support modified products, having said that almost all printers use the same types of connections, however i don't have a pinout of the Neptune 4 Board to be able to say for sure that it would be plug and play. The best way to achieve what you want however would be to simply install Klipper onto the Neptune 3 Board, you'll need a host such as a Raspberry Pi or for novice users a BigTreeTech Pad 7 would be ideal. the Neptune 3 Board takes Klipper no problem and it performs very well and doesn't require you opening up the printer or fitting different boards etc.

[@makermylo]

Heres my Neptune 3 Plus, with the stock mainboard running Klipper doing speeds and accelerations 2x faster than a Neptune 4, you don't need the rails for it either, properly adjusted wheels on the stock carriages will handle it just fine.