Ender 3 Pro to Voron Switchwire Conversion - Part 4

[@nitroburner77]

I appreciate your videos! I plan on doing this build, and will be referring to these when I do.

[@HyperMakes]

Have fun!

[@corey312]

this video series got me through the full build with no confusion! great job and thank you!

[@corey312]

I have a question, I have finished the conversion and am re using the creality silent board with the original hotend until this red lizard dragon clone come in from aliexpress. what all do i have to change in klipper config? I have a bl touch and ran iton the same issue as you did with it being too low so I swiithched to an omron probe I pulled from the parts bin after I switched to klicky on my trident. also the ender 3 I converted was already running klipper and mainsail on a pi zero. thank you

[@HyperMakes]

Thanks. Glad you liked the series.

[@HyperMakes]

If you are asking in the context of what you have to change in config after the new hotend installation, the things are new pid calibration for hotend, rotation distance of extruder and finally pressure advance.

[@guillorylild]

Nice I’m finally finishing up with mine too went with a spider board finally finished wiring it last night and got everything running right can’t wait to see the enclosure video

[@nirawitnitinunsupkit6281]

will spider board fit under ender3 frame? I also looking to buy new mother and spider look pretty good.

[@guillorylild]

@@nirawitnitinunsupkit6281 yea I had just enough room for it and a pi zero 2 w I did an Aquila switchwire conversion but the Aquila and ender should have pretty much the same frame it was just hard to find a mount for it I had to reach out to the voron discord to find one if you need it let me kno

[@nirawitnitinunsupkit6281]

@@guillorylild sorry to ask why not SKR mini? Also my plan to use spider is separate the electrical box due to the big board will be too fit for everythings.

[@HyperMakes]

Nice work! Part 5 might be up on the channel by next week's Friday or weekend.

[@guillorylild]

@@nirawitnitinunsupkit6281 already had a spider and octopus board laying around but picked the spider because I couldn’t find a mount to put the octopus mounted to the extrusion plus I wanted the extra ports for fans and thermistors I’m already running an Skr mini e3 v3 in my ender 5 pro and it just feel to simple to me I wanted something more expandable

[@jmsfer]

Thank you my friend !! As always you are an inspiration!! Looking forward for your ideas on an enclosure as I am planning my own! Hope to learn something from you :-)

[@HyperMakes]

Thanks mate! Sure, stay tuned.

[@midoriFPV]

Long time no see i wait your clip . good job bro.

[@HyperMakes]

Yeah thanks and welcome back!

[@mihaivasai4919]

Dude you are awsome. I feel realy bad for the PI so i doneted a couple of coffes to contribute for a new one :)

[@HyperMakes]

Thank you so much mate! It surely helps. Cheers. ✨

[@joseph3164]

do you have a pateron? I would like to donate for all the great content you provide. Or at least buy you a new RPi. Thanks, I enjoy the videos!

[@HyperMakes]

Just made one! You can support me on Ko-fi now. You can head over to the community tab or channel banner of my channel for the link. Anyways here the direct link if it helps: ko-fi.com/hypermakes2620 Thanks for the love and support!

[@lanypuspasari1868]

Great job bro.👍🏽👍🏽👍🏽

[@HyperMakes]

Thank you! Cheers!

[@jamjestlx]

Amazing! I need to build one :D

[@HyperMakes]

Go for it!

[@KennethScharf]

I have an Ender3-pro that I wish to upgrade. Your videos look interesting. I assume you bought the parts kit for the sw conversion. Did you get the kit that came with the 3d printed parts, or did you have help printing them. I might just print parts in PETG. I know this is not recommended by Voron, but I really have no need to print in ABS, so I might not enclose a sw conversion. I've previously built a reprap / repstrap printer with PETG and PLA parts, and I never had any parts fail. Then again, I never printed much ABS. Also my homebrew extruder was all metal. I am going to use an HPT520 thin client instead of a RPi. It has a dual core AMD processor (about 1ghz) with 4gb ram. I upgraded the SSD (SATA M.2) to 128GB. It is now running Debian testing with Klipper. You can use the axl135 accelerometer with a RPi Pico connected to your computer via USB (google for youtube video on how to do this). It works with klipper as if directly connected to the RPi GPIO pins.

[@HyperMakes]

During my time kits were not available. I had to source the parts myself, even the printed parts were printed by the printer itself inside a foam enclosure. You can use PETG if you want but it does have material creep. If possible i would suggest to print the hotend housing parts in ABS, that's it.

[@sabergo1]

Well done (except the Pi). I feel your pain on the Pi though, very hard to find to replace, and the prices are absurd right now. Was all the work worth it? Look forward to the next project. Edit: Set up a tip/pay line -- maybe pocket money will take care of itself?

[@HyperMakes]

Yup, planning about it and will be setting up some kind tip system as soon as my channel gets monetised.

[@everythingxyz1499]

Make separate video klipper and fluiddypi installation process

[@deathcogunit106]

I am doing the same conversion right now. ABS is a pain to print.

[@antallaczko8793]

Why? I have printed 1 set of V0.1, E3Pro to SW kit already and halfway with V2.4 on stock ender, with glass bed, BLTouch, all metal hotend in a cardboard box, in my shed. Outside temp between 5-12 degrees, inside between 16-34. 50 mm/s, bit of Z wobble but that's the stock 8 bit machine. Planning the conversion in 2 weeks time.

[@HyperMakes]

Yes, a little worrisome for new people into ABS printing. But as long as you have a extruder that can print at ABS temperatures and an enclosure, you will be loving it.

[@HyperMakes]

Great. Have fun building your voron printers! 🥳

[@JorgeGomez-tj6cl]

The assembly of the machine is very good but the wiring of the PCB toolhead is impossible to understand how you have connected it. I can't understand where you connect the 24+

[@HyperMakes]

Have you checked out the wiring diagram i have shared in my repository? Here: github.com/Kruze17/HN_Switchwire/tree/main/ToolheadPCB_crealityv4.2.2%20wiring%20diagram

[@JorgeGomez-tj6cl]

@@HyperMakes yes, and I have verified that the diagram has two errors in the connections of the limit switch of x and in that of the probe. The drawing indicates the upper pin even though it must be the lower one in both cases. purple and blue lines.

[@madorax251]

cant your share steper motor x and z wiring diagram?

[@HyperMakes]

I have not used the stock creality motors, so connection is simply plug and play. For creality motors you need to swap the inner two wires.

[@AJayTheStageArtist]

Hi sir will u make input shaper with ADXL345 tutorial at future for Ender 3 Switchwire ? Thank you so much

[@HyperMakes]

I may or may not. Currently i am on a break due to higher studies. So depends.

[@AJayTheStageArtist]

@@HyperMakes i see, thanks for the reply 😀

[@Bukton5000]

Where is the STL for the Raspberry Pi 3 A+ Mounting system for the electronics at 2:41:00 ?

[@HyperMakes]

I have messaged you in discord about that. Anyway giving the link here too: github.com/boubounokefalos/Ender_SW/tree/main/STL/Electronics look for rpi mount and rpi shelf.

[@Bukton5000]

@@HyperMakes Hey I just checked and couldn't find the message. I appreciate it and will send you a message on discord. I'm gonna watch the latest you put out today. Thank you for the help.

[@user-vz3rf8kj3z]

My switchwire is moving strangely.When you move the x-axis, the z-axis moves, the x-axis moves, and when you move the z-axis, the x-axis moves, and the z-axis moves.Help me

[@HyperMakes]

Join the official Voron discord server. People like me can help you out there. here is the link: discord.gg/voron

[@williamwiese9963]

What size bolts are in the fan shroud?? Great video

[@HyperMakes]

Sorry for the late reply. The fan shroud uses M3 size socket head bolts.

[@lanypuspasari1868]

Cant your share printer.cfg your using for v4.2.2 and superslicer config for enser 3 SW

[@HyperMakes]

Please visit my printer's Github page. I have hosted all the necessary file there. github.com/Kruze17/HN_Switchwire

[@benkeenan7553]

I don't know if you have a way to donate to this channel but I am loving the project so far and would be willing to donate to the Raspberry PI fund. 🍓🥧

[@HyperMakes]

Thanks for the love and support. I will be setting up some kind of tip system as soon as my channel gets monetized.

[@tkaemendez8428]

I'm in same boat financially but can manage with no real consequences $20 USD...if you have a PayPal

[@HyperMakes]

You can support me on Ko-fi if you want. It has Paypal integration with it. Also thanks for supporting and watching my content.