Engine cranks but won't start

Here are some of the tools that jimthecarguy uses
www.amazon.com...
Noid lights amzn.to/2WdvYwz
No start, cranks ok ,spark OK injection pulse OK no fuel pressure How to check no start on a Ford,Lincoln Or Mercury

[@DonaldWhitson]

Your video made me appreciate a good mechanic who knows what they are doing. We complain about what they charge but they often deserve what they get paid. It is difficult to find a good one you trust. Good job. I have a 96 Ford F150 that had intermittent shut off/restart issues I bought last summer but now cranks but won't start. My mechanic has not nailed down the problem and doesn't want to just start replacing parts. Another KZbin video turned out to be the inertia switch. When weather improves here in Greenbay, guess I will get out there and tinker with it myself. Or get it towed somewhere. Thanks for your tips.

[@KeithOutWest]

Donald Whitson - Did you ever get it fixed? What was the problem? Thanks!

[@stickerchief5449]

thanks for sharing a friend just called me about her truck not starting i looked it up and now i know where everything on her vehicle is and did the process i figured it was the fuel pump when there was no humming but its nice to know the extra steps. the pulsing and all the connections and special tools needed.. thanks again.

[@jimthecarguy]

Thanks for watching. I'm happy to help.

[@carelesswhisper1148]

Lucky girlfriend..

[@bobolszanowski5919]

Thanks for the step by step diagnostics. I did them all and found the crankshaft position sensor was the issue. $19.99 and a little elbow grease and my 98 Ranger Starts! I appreciate ya! Bob O.

[@jimthecarguy]

I'm happy to help. Thanks for watching

[@BeastmodeBeats]

It’s either the fuel pump fuse, or the fuel pump itself if you can hear a car crank, if the starter wasn’t receiving power you would hear a click when cranking rather than actual cranking noise, also, if you hear the beeping noise when the key is in the ignition, the fuel pump is receiving power from the fuse. But the real question is, is the fuel pump working properly and creating enough pressure to pump fuel into the fuel tank

[@yolandamartin5006]

When my husband turns the key in the ignition you can hear the click what does it mean.

[@semco72057]

That was great and I may have a fuel pump problem with my Ford Explorer (1999) which ran great until I parked it the last time, and when I tried to start it again, it would not start, but would crank up normally. I can't remember if I had replaced the filter on this vehicle since I owned it in 1970. I have a tool to put replace the filter on one Explorer and also on a 1987 S-10 Blazer I still have. I thank you so much for the information, and hope it works for me.

[@zakureemeyer4058]

There are different fixes for Crank No Start. When you work on the engine for a while you do something to the settings of the vehicle and you might need to do a reset this will clear old codes too. Ok disconnect negative cable and get another wire maybe one side of a jumper cable and put one end on the Negative CABLE make sure it is away from the battery terminal may be put a rag over it to make sure they don't touch then touch the other connecting end to the positive side terminal for one minute. another CRANK NO START fix is to check Crank Positioning Sensor THEY ARE USUALLY OUT OF SIGHT FROM THE TOP OF THE ENGINE. They can't be forgotten after pulling the timing chain cover off. on a 99 ford Expedition 5.4 its underneath passenger's side. With it unplugged it will still have fuel pressure but spark.

[@IQ-pr7cz]

This is how you do it people! Straight FACTS.... Thank YOU so much...

[@jimthecarguy]

Thank you for watching . I'm happy to help. Don't forget to subscribe.

[@vatcheohanian2565]

Thank you very much Jim... Your information helped a lot. No i don't have any pressure at all... but gas did come out from the valve when i press it. I have cycled the key several times.

[@lajeanapeoples5294]

Thank you so much for getting straight to the point 👍🏾

[@jlmiami1]

Thank you great instructional video Now I'm running to my mechanic that's a big job. Thank you very much.

[@bulletproofpepper2]

Thanks for the great tips and knowledge. Wasn't working on a mustang but have the same problems. Thanks for sharing.

[@jimthecarguy]

+sam yeates I'm happy to help.

[@irishincal1019]

I love you man, you do an instruction the way it should be done. When mine is running I will be sure to publicly credit you. Thank you.

[@maliakuheana705]

,0 ml j koo 956a

[@joesmoe5006]

I know this is an old video but if you have a Ford probe GT and it won’t start back in the day the common problem was the distributor they go bad so just go replace the distributor and it will start right up no problem I went through four different distributors back when I had a probe

[@will153]

For mine - 2004 Triton V8 - it doesn't happen in the morning or after it's sat for 2 hours or more. Only if I drive it, stop for a few minutes like the gas station or grocery store then try to start again after only sitting for 10 - 30 minutes.

[@GILLEBRATH]

Interesting and logical fix. I have engine turn over , no spark , no gas , gas gage not responding , haven't checked pressure yet but cannot hear gas pump so what next ? fuel pump relay ? I am checking fuses for a short but no luck yet . I do have a short because there's a spark arc at batt . cable and an engagement noise, that I suspect is where my short is coming from. It is a 97 Blazer 4.3 and any ideas would be a great help .thank you Jim.

[@JoeJ94611]

Thanks for sharing this info especially those fire safety tips for the "screw-it-up-yourselfers" like me!You've invested lots of money in all those tool boxes!

[@jimthecarguy]

thank you for watching and your feedback

[@emersoncampbell2661]

Thanks now I know how to check the vehicle and remove.replace a flue pump

[@TheLoriGosselin]

My husband watched this video because we had the problem with our 97 Ford after minor work he did (shocks replaced) and it wouldn't start. He discovered (thanks to the serendipitous visit of a neighbour) that the fuel pump shut-off switch had tripped because he was bouncing the car to check the shocks and lifting and lowering it and dropping it. He pressed the red reset button on top of the shutoff switch and then when he turned the key he could hear the fuel pump run again. It started!

[@jimthecarguy]

Lori Gosselin Thank you for your feedback and for watching.I' m happy that my video was able to help you.Jim

[@deborahbennett6278]

+Lori Gosselin where is the red reset button

[@jimthecarguy]

+Deborah Bennett Depending what kind of car .It may be in the trunk or in one of the kick panels inside the car .If you still can't find it email me at work on Monday I will look on my computer.

[@Terra-cotta-pendants]

+Deborah Bennett Sorry - didn't see your question Deborah1 Glad Jim is able to help!

[@slicknick484]

+jimthecarguy do you know where a reset button on my 96 toy.camry would be located?

[@Naturally-Kelly]

Really great video on how to diagnose. Appreciate the work that went into it. Off to diagnose my Ford Expedition :)

[@zebarz]

Hey Jim, I have a 2002 Ford Mustang 3.8L V6. about a year ago, I had a crank no start situation. I changed out the Spark Plugs, put ina new battery, fixed the problem. a couple months ago, I had to have surgery, and was out of work for 2 months, I went to start the car, fired up, then the whole car shook, really bad idle, and when I tried to give it gas, seemed to make it choke even more. I assumed that it may have water in the tank, due to the weather change and from sitting, so I put some of Sea Foam or whatever into the tank, I also pulled the Idle Control Valve, cleaned it out, and put on a new gasket. Disconnected the battery, and it still crank no start. I'm getting fuel at the valve, the red pump reset button is pushed down already, cannot press it in the trunk, Theift light isn't an issue, any ideas?

[@jimthecarguy]

+zebarz Will the car start and just idle?When you give it gas did it stall?Did you check the fuel pressure ?Keep me posted Jim

[@zebarz]

+jimthecarguy The car won't start at all, it just cranks. I did get it to start initially, after I Jumped the battery, I let it idle for about 2 and a half hours, to make sure the Alternator had time to recharge the battery, when I went out to move it into the garage, it started choking and did even more when I pressed the gas. I am kind of thinking that perhaps, since it was sitting, when I started it, it sucks stuff into the filter plugging it, I had a mechanic come out today, he believes it to be the fuel filter. I am having him come over tomarrow and install a new one, hopefully that's all it is. I try to do everything I can myself, but as I have stitches from an Incisional Hernia, I cannot lift anything. He charged me 48.00 to come out, and he stated its gonna be about a half hour to hour job tomarrow, which I think is right, Fuel Filter is easy to get to. You can clearly hear the fuel pump kick on, and I know that doesn't mean its not working right, but at least the Fuel Filter is a start, its just over 100k miles. Thank you so much Jim for the fast reply. Ill keep you posted.

[@jimthecarguy]

+zebarz Great

[@zebarz]

+jimthecarguy Ok update. Mechanic came, put in a new Fuel Pump, Fuel filter. Car still wouldn't start, disconnect battery, hooked back up, seen that Fuel pump fuse was blown. Put new one in, still wont start just cranks. Mechanic is coming back tomarrow to do electrical diagnosis.

[@PaulHenreid]

put the solution in the description so time is not wasted

[@jamesbrant352]

Mine was a bad plug end at the TP. Fixed it runs like new it wouldn,t crank over had a p0601 code

[@IQ-pr7cz]

96 Cadillac DeVille has fuel pump pressure has spark cranks over won't start. Sprayed starter fluid into the carburetor area. It starts up runs for 10 seconds then shuts off. Check all the fuses none of them were bad. Check the PCM it's fine. Bought a set of Noid lights to check the fuel injector power. No flash. Now I know the fuel pump is brand new. The old one wasn't even bad. The oil pressure switch ack's a fuel pump relay backup I'm wondering if that's the problem. I got up under there to look I didn't see no oil dripping from it but that still doesn't mean that it can't be bad. I brought a new fuel pump relay fuse and it's just fine. But soon as I spray the starter fluid into it it fires right up. The fuel pump pressure regulator is not leaking so I don't think that's my problem either. I'm stumped on this any suggestions

[@hi-ol-ag4811]

this is the best video I have seen to date. very informative and helpful...too bad he did have an extra hand

[@jimthecarguy]

+Stephen Rodriguez Thank you for your feedback.Oh if I only had a 3rd hand work would be soooo much easier..Lol

[@yolandamartin5006]

My husband was driving in traffic and the truck cut off. He tried to crank it up it didn't do any. When he got a boost off it crsnk but cut right back off. My friend said the fuel wasn't getting to the motor. Do that mean the fuel pump went out? We have a 2008 GMC Acadia.

[@jackgafford]

Ford has a running problem with this that involves a new harness running to the fuel pump and a larger fuse...the harness is on national back order so I'm thinking it's a huge problem....Ford dealer repaired mine with a bypass wire and larger fuse and it works great.

[@Joeelectronicschematicsforauto]

I love your channel

[@tahotoy]

Jim, with all due respect, why check ignition and injection when no fuel press was found?

[@JeffStAndre]

Dropping alike for the content and the stabilization in editing

[@EndofUSA]

HI Jim. I have pulled out halfway the fuel rail with the injectors still attached and started the car. I discovered that the injectors won't fire. then I tried pulsing each injectors separately and they do fire fuel. So what does this mean? Do I now go for the ECU? It appears that the injectors are not receiving voltage pulse for them to fire from the ECU. And if so, what do I check for in the ECU? How do I repair it? thanks

[@jimthecarguy]

+EndofUSA Thanks for watching and for your input

[@ange1vega]

Btw, i was trying to started before checking for fuel pressure so I used lots of starting fluid, maybe I flooded it? Thanks for any input!

[@melodyjaques9671]

I have checked fuel pressure timing cap rotor coil and cap

[@netsurfers9357]

That's why I like a mechanical fuel pump on the engine, much more efficient with less hassle!

[@keishla_ramos836]

I have a 2005 explorer. I've been trying to figure out what's wrong for a whole week an a half. Already changed the fuel pump, with it's filter. Also, checked the crank. I bought a new, because I thought the old one was not getting any connection, yet with the new one it still won't spark. When I try to start her, she won't start. In the monitor to the left (inside and next to the miles counter) it pops-up "test"... Could it be the key or a relay?

[@samrugtiv5563]

very well done old pro

[@KeithOutWest]

My 2003 F-150 5.4 Triton cranks without starting sometimes, then other times it start right up. Could that be the fuel pump going bad slowly, or do fuel pumps just die fast? Thanks!

[@fuaimoa9236]

Also when I stepped on gas paddle at that time it was working..I have sort of lite bit hard time to press on it. But if I do, it slows me down.even more. Please help me.

[@gabrielac0sta522]

What if all my fuses checked out good but on the fuel selector switch I had less than 12 v one wire was reading 8v and another one 6v on

[@spagsketti]

Oh man you did that pump the hard way. only 6 bolts hold the bed on. Take the bolts out unplug the tail lights and take the bed off. don't even have to drain the tank.

[@jerrymcclure5636]

tks Jim. the car turns over like normal just won't crank unless you use cables. its like its giving it extra voltage. I do not hear the fuel pump unless I do this. after cranks runs normal no cut out or jerk like pump is bad. tks jerry

[@jimthecarguy]

+Jerry Mcclure Do you want to call me so we can talk?I'm closed for the next few days but i can talk to you on Monday.Let me know

[@jerrymcclure5636]

+jimthecarguy that would be great

[@LiilTyweezy]

+jimthecarguy hey what's a contact number i can reach you by

[@julissaandino87]

I have a big issue, I just bought a used 06 chrysler 300 last week and it shut down on me twice on the highway as I was driving I tried to turn it on and no luck.. my friend put in $3 worth of gas and after turning the switch several times it started but the weird thing is on the dash before my car shut down it said it had 3/4 of gas so I need help?? What can it be?? I'm a woman and have no idea when it comes to cars😢

[@matthewdeanl5884]

I've just been through Hurricane Harvey. My lincoln 1998 towncar was flooded but no water in the engine. Now, it does not even turn. what can I do. I tilt it with my 2tons jack and about 3 gallon of watrr came out. How can I get my car to start again? beside taking it to a mechanic . thanks in advance

[@vatcheohanian2565]

how much pressure should there be on the schrader valve. on mine gas did come out but didn't notice pressure... thanks!

[@jimthecarguy]

There should be any where from 35-55 lbs of pressure .Remember that you will need to cycle the key a few times to build pressure.When you press in the valve the fuel should spray up at least several inch high.Be carfeul with the fuel (no sparks)Some of the big auto stores rent equipment check if you can rent a fuel pressure tool.. Good luck

[@madblade]

Great video I have the same problem with the same car. I don't have power in the connector at 9:20 in your video, but I do have power going to the inertia fuel cutoff switch, and to the fuel pump driver module. What do you suggest?

[@georgemulder4452]

madblade JIM MAYBE YOU CAN HELP ME .MY 2L OPEL REKORD BERLINA WON'T START BUT WHEN I REMOVE THE TERMINALS ON THE INJECTORS IT STATRTS WHAT COULD BE THE PROBLEM

[@michellemotta6890]

I have a 94 mercury cougar and I have a new fuel pump and it cranks but won't start can anybody help me?

[@starcraftcoltd962]

your vdeo quite helpulmy Toyota Noah 2008 edition cranks but wont start, still NO power on EFI fuse yet all other fuses have power, where should i chek

[@rickyspangler7052]

my 1996 chevy 1500 5.7 engine cranks like it out of time iv,e put timtng chain andgears and cranking sensor and timed it

[@rickyspangler7052]

I need help I,ve tried ever thing

[@To-Masz]

My mazda cx 9 has a 3.7 Ford engine. For some time now, the engine of the night stop has been turning on and off. It starts the second or third time. Then it starts normally. I cleaned the fuel mesh filter. Is it a faulty fuel pump? Forscan shows error p0171 - poor mixture of cylinders group one. What is going on? please help

[@godsmackedyeah5834]

I have a 89 mazda b2200 that doesn't have spark coming from the ignition coil but the resistance test shows it to be good, engine turns over but wont start. It doesn't have a cps. I thought it may be the ignition switch but it is turning the engine over. Any advice? Im at a deadend,lol. Thanx

[@nathanielselvidge4157]

So what happens if I have spark and I have fuel pressure?? I have an 03 f150 that just won't start at all! Just cranks and cranks. And every once in a while (on a very rare occasion) it will start. But once you turn it off. It is back to square 1! Please help. Very very frustrating

[@Heatlifer305]

Hello, I have the same problem on my 1990 mustang, it died all of the sudden, seemed liked the fuel pump, so it was replaced, but still have the same problem it won’t start, you hear the pump running and won’t shut off. Help Please!!! Thank you.

[@garryanderson2710]

If you have the dizzy cap off and you try start the car is the rotor still meant to move?

[@TookMe20min2findThis]

Thank you Jim for your videos. Just one question: knowing you didn't have fuel pressure, why did you check the injector anyway? (routine check ?)

[@jimthecarguy]

Yes because if there was no pulse then I would need to check what the two have in common. Very good question.

[@TookMe20min2findThis]

@@jimthecarguyOK I see your logic. Indeed you want to make sure its really the pump and nothing else once you undertake this removal procedure! Thanks for the quick follow-up I appreciate.

[@likefollowandsubscribe516]

fuel pump changed icm relay always burned is it ECU problem and need to change??

[@kidsarcaderoom7316]

You did a awesome job :-)

[@jimthecarguy]

Thank you

[@delfis42]

Hello jim! i have a 2001 f150 with a code p171 i checked it and noticed it was a pcv hose. i replaced but now it does starts on but don't run. i checked for any unconnected hose and everything looks ok. i even cleaned the full throttle body, mass sensor, new air filter and still don't run.. what do you think it might be? it was perfectly fine and running before i noted the pvc hose had a hole wich i assume the reason for p0171 code. it starts on.. stays on but if i put it on reverse or drive it just don't have power.

[@jayp2326]

delfino Hernández catalyst converter try that

[@sjaxemaster11]

fantastic work jim. love your videos champ

[@OctoberBlues89]

I've changed the fuel pump and filter it started fine for 2 weeks but now it cranks but won't start Can you help me out?

[@johnedwin4995]

Cranks! But will not start. Starts after repeadely pumpin accelerator. Starts poppin a missin. After 30 seconds it begins 2 start. Haveim 2 pump it 4 a bit till it finally fires up! Once it gets 2 running! No more problens 4 the day !

[@davidgaleski5303]

horses get sick TOO LOL

[@jimthecarguy]

+david galeski Thanks for watching and for your input

[@rogerd4559]

I was told by others on KZbin that it is better to listen for a click from the injectors with a stethoscope

[@jimthecarguy]

Here is the link for the noid lights. amzn.to/2WdvYwz

[@carlhicks5999]

Jim, they put it on a diagnostics tester and the only thing it showed was a crank position sensor. Does that sound about right? Can you send me a video on how to change one on a 2002 accent.

[@jimthecarguy]

+carl hicks Most likely the sensor is no good if it show the code.I don't have a video for replacing the sensor but the sensor should be on the front left of the engine by the exhaust.(left is the driver side) keep me posted

[@seanwilson5916]

Does this work on a 429 big block

[@hatesTD]

Hi Jim I have a 99 crown Vic that I had to replace the gas tank a fuel pump my car was sugered...the mechanic who I brought it to put a used gas tank (not happy with that ) and a new file pump..I also replace two injectors and fuel filter. Blew out the lines as well..the 2 issues I have is the car runs fine but if I drive it after say 5-10 minutes a she'll stall out and it's hard to start..the second issue I have is I can actually hear the fuel pump whining when cars running when I open my trunk and stick my head in..I've checked out 2-3 other crown Vic Grand marquis and I don't hear the pumps whining at all..I was told that done aftermarket pumps will whine..what do you think?

[@jimthecarguy]

+motts722 Thanks for watching and for your input

[@richardsmith1289]

motts722 pop

[@hunkydude322]

how did u go about empting the tank, what did u use. good video.

[@jimthecarguy]

+hunkydude322 You will need to use a very thin hose to drain the fuel tank

[@dashtyATG]

Can somebody help i have Nissan tiida 08 Ger Ato it crank but wont start fuel pump has been tested all good, i have even cleaned the plugs ones it was gon fine for a day then same happened again! please help if you can

[@vatcheohanian2565]

Jim, a very important question... Do these mustangs have a fuel pump relay? I have checked in the owner's manual but found only a fuse for the fuel. The fuse was good but i want to check if the relay is bad (if it has one)...

[@jimthecarguy]

No on this car there is no relay I will attach what my repair program said. Good luck let me know how you do. Remember be careful with the gas and the fumes from the gas. Fuel Pump Relay is not serviceable. The Constant Control Relay Module (CCRM) contains the fuel pump relay, which supplies power to the FPDM. If any of the internal components of the CCRM fail, the entire unit must be replaced

[@robertorodriguez6772]

I replaced the engine in my 2003 Ford explorer 4.0 with a remanufactured directly from Ford. My question is does changing engine throw the vehicles computer off. It did start the day the new engine was installed but can't get to start again. Thank you for any ideas and help.

[@jimthecarguy]

I do a live stream on Sunday night I will talk about this on my jimthecarguy show tonight at 7:00 PM (EST).I hope you can stop by.

[@fernandojimenez7809]

2000 chevy astro van 4.3l wont star good compression spark and fuel pression no codes any sugestions thanks for your answers my name fernando jimenez

[@brendagarland386]

ok im baffled ...........bought a 1999 ford f150 been sitting for about a year had parking brake stuck and they thought rear end was out...got it home fixed the problem drove it about 6 miles noticed front brakes hanging up so it sat about a week until got the issue fixed went out to start it to move it to mow.. It started and died Started then died It cranks no spark fuel pressure is running about 38psi checked all fuses and relays tightened all grounds to firewall what can be the problem ............replaced cps and still cranks but no spark thanks for the help

[@spagsketti]

Fuel inertia switch fords have them

[@oldtwinsna8347]

Wow this seems incredibly labor intensive. How much would this job cost ?

[@rogerd4559]

probably more than the car is worth

[@dedicatedrecycle731]

jim,i have a 2000 ford expedition 5.4 it has a crank no start issue but it only does it sometimes.not all the time.most of the time its been cold weather situation.so im thinking crankshaft sensor,it was very dirty washed it power washer the next morning 25 degrees it starts right up,next day 27 degrees starts up,finally 50 degrees it wont...help

[@jimthecarguy]

+Dedicated Recycle It is possible but you will need to do more diagnostics before you replace it .Check out my videos for further advice.

[@gregorygambold3508]

I have a 2000 4.7 4 wheel drive that just died while I was driving. on my way home from work for a week it would put it self in to limp mode I would reset the truck and it would run just fine Intel I was on my home the next day. I replaced the starter the computer PCM the crank and cam sensors the water pump. fuel pump does come on gauges work but no abs light no check enige light and no secertiy light what could it be???

[@JohnGarnerIII]

swap your fuel pump relay with the blower motor relay and try starting. If that doesnt work than swap blower motor relay with PCM relay. Seems silly but worked for me. If it works than buy a few back up relays and keep em in your glove box.

[@1ciroloid]

Trade it in for a Kaiser Frazer.

[@hainistephen7759]

My hyundai elandra died out when I stop, what do I to plz help ,I'm not a mechanic

[@melodyjaques9671]

hey my 1996 chevy 5.7 cranks but won't fire what's wrong

[@georgenicholas3127]

where is the fuel shutoff switch on a 2002 Jeep Liberty

[@rogerd4559]

where can I find that test light to test the injector signal? I dont see it in the list of tools you posted

[@jimthecarguy]

Noid lights. amzn.to/2WdvYwz

[@garryanderson2710]

If your dizzy cap us off and you try start the car is the rotor still ment to move??

[@kristahunter1588]

not that I know of you can adjust it but it should not be moving loosly not sure if that helps

[@brianmitchell3330]

My truck has spark and gas to the tbi and still won't start it's a 1992 gmt400

[@luismontemayor5713]

I have the same problem and I replace the fuel pump cause I dirent have any pressure of fuel to the injectors.... Now I have fuel to the injectors but still no start I check all the fuses and rellays.. And the switch on the trunk and nothing

[@gordontrainer]

There a fuel shut off switch under dash driver side

[@dylanhill476]

Hey was wondering if anyone could help I got this truck almost a year ago it ran twice now anti theft is on ? looking at it and pretty sure an engine swap was done and things are spliced and fuel pump sensor is by passed then the engine block ground is snapped what and anti theft is on its got crank but no spark is it anti theft if so how do I rest it ?

[@joshwebber98]

Does your key have a computer chip? Crankshaft could have been damaged during engine swap.

[@joeclark1439]

own a 2000 BMW 740li. I parked it for three months. Went to drive it. Battery was dead. Replaced battery and the car will crank over but not start. Replaced crank shaft sensor, still no start. I have no fire nor fuel. Suggestions?

[@jenniferpeterson2868]

Joe Clark b

[@JohnGarnerIII]

check PCM and fuel pump relays. try swapping them out with relays from blower motor.

[@raoulwright4484]

I have a 2008 infiniti Qx56 and I have this problem. cranking but not turning over. any suggestions?

[@jimthecarguy]

+Raoul Wright You will need to do some diagnostic first.Follow the procedure in this video and you should be able to narrow it down.Let me know if you need and further advice.Jim

[@jerrymcclure5636]

hi I have a 2000 lincoln continental that well only crank if I jump start it with cables and another car, I know that battery is good, I have also tried another new battery in it, will not crank without putting cables on, everything looks clean please help. thank you jerry

[@jimthecarguy]

+Jerry Mcclure Hi Jerry ,When you try to crank without the jump start what happens?When you put jumpers on it do the car crank right up or does it sound like it is cranking slow?

[@jerrymcclure5636]

jimthecarguy hi jim, it turns over normal both ways,but wont crank unless cables are on it, strange, tks jerry

[@sqakdaddy]

i have a 1999 ford windstar. i put a new MAF in it. now the thift light flashes all the time. i turn the key. and it really flashes. for a min. then it stops flashing for a few secends. then it does that about 3 times. then it flashes i think it was 8 times in a row? and there's no spark? if you can please, help me with this? thank you for your time.

[@jimthecarguy]

+Donald Sanders Do you have a second key for the truck?If you do try that key .Keep me posted.

[@sqakdaddy]

i got it used, with only one key.

[@jimthecarguy]

+Donald Sanders Does the key have any broken parts on it .The reason I ask is because the key has a chip in it.

[@sqakdaddy]

no it does not

[@jimthecarguy]

+Donald Sanders You will need to scan the van for codes.

[@dylanhowbigistheliftonyour4883]

I have a 1999 förd Explorer söme öne put sömething in my gas tank sö i dröped the tank cleaned the tank öut put new fule pump. In blöw öut all the lines and new fule filter and still wönt start whats next????

[@jimthecarguy]

I'm happy to help. Live stream Sunday night at 7:00 PM on jimthecarguy.I hope you can stop by.I will talk about this problem.

[@zulnoon78]

good video , thanks

[@janicecarpenter1594]

02nissan sentra gxe..coils have no fire.replaced cranksensor.still no fire.any advice.car runs good parked 2 weeks.turns over will not start. coil pks dead.

[@1CoLoRz2]

could be a key issue. is there a theft system in your car? also check all your fuses.

[@victoriaburfeind9007]

My 1CoLoRz2

[@rogerd4559]

Im trying to find a way to hook up my compression gage up to the Shrader valve. I was told that if the pump is putting out less than 25 psi that it may not be enough to start the vehicle

[@jimthecarguy]

That is to low to run the car.

[@Butterflytaxidfw]

what if you cannot get to the spark plug wires, because they are under the valve cover?

[@jimthecarguy]

Butterfly Taxi DFW There should be a cover over the plugs that will have to be removed so you can get to them.

[@Butterflytaxidfw]

It is not just a cover, it is an intake manifold and it takes an experienced mechanic a couple of hours to change them out, so I can imagine how long it might take me. Thanks for replying.

[@jimthecarguy]

Good luck.

[@MrJusticemiles2003]

2003 fuel module replacement and location. Can't seem to locate mines

[@jimthecarguy]

+MrJusticemiles2003 The fuel pump driver module is located in the trunk above the left rear wheel.

[@MrJusticemiles2003]

+jimthecarguy Thanks, but I have a F150 2003 Lariat truck

[@w32x]

Question! I have a 92 Nissan pickup with the 4cyl and itll crank but wont start. Ive changed the plugs, ignition coil, distributor cap and rotor button, and the fuel filter. Any suggestions?

[@jimthecarguy]

+w32x Thanks for watching and for your input

[@tannerwear9101]

check your battery lines both positive and ground, to make sure the lines aren't corroded. was there a lot of corrosion around the + and - battery connectors??

[@w32x]

No there wan't any corrosion. We found out now that my timing is off and we're struggling to get the timing set with the distributor and the oil pump

[@tannerwear9101]

ahh ok cus I literally had the exact same problem and it was my battery lines. Both of them were more green corrosion than copper. looked like the statue of liberty I'm not kidding lol. once I replaced those and one relay fuse everything was perfect.

[@tannerwear9101]

Good luck! what kind of vehicle? sorry just re-read ur original comment. Good luck tho I've worked on my 2002 GMC Sonoma pick up and it has a stupid vortec which just creates a bunch of problems for my alternator, battery, fuel lines, I mean it has to be maintained literally weekly but I try to maintain it every couple weeks.

[@williamhaines856]

very good thanks

[@luismontemayor5713]

Now I got it fix it was a short on the car stereo... And I also change the cam shaft sensor

[@marloluevano5662]

Where was the short? My car radio went out. It turns in but no sound was coming from speakers. Now my car won't start. It just cranks .....

[@marthagarcia5279]

I hav4the same problemdid u solve the problem

[@luismontemayor5713]

Martha I did fix it i had a short on mine car ..the stereo wires were grounded.. And it could be alout of things like fuel pressure fuel filter ,fuel really, fuel fuse.. No spark ,could be your coil pack ..could be your fuel injectors!! Fuel pressure regulator.. your timing your little computer that controls your injectors if your not getting fuel in to the injectors

[@luismontemayor5713]

@@marloluevano5662 you could have a short in your wires.. check them twice.. And sorry for the late response

[@tobbyy125sammyy]

some good info here

[@davidvalencia1837]

tobbyy125sammyy

[@jamesmanous9608]

I do not have any Spark on the engine

[@jackieg9244]

We are having an issue like this with a 2003 ford mustang. It's stuck at a store until we can get to a shop. Any advice to get it going to get it to a shop or do we have to tow it. How much does something like this cost?

[@jimthecarguy]

+Jackie G If the fuel pump is the problem sometimes you can get it to start by hitting the fuel tank when you are cranking the car.This may cause the fuel pump to start to work enough to get it to a shop.Git it a try .Keep me posted.Jim

[@jackieacosta7031]

+jimthecarguy didn't work

[@jackieacosta7031]

+jimthecarguy didn't work

[@jackieacosta7031]

we tried to put a little gas in to see if that would work.... it didn't

[@dukeman7595]

Why don't they place the fuel pump access on the bottom of the gas tank with a drain plug. It would sure make life easier..

[@jimthecarguy]

+Joseph M Oh that's easy .The engineer who design the car just love to screw with us .Lol You know years ago they did do just what you said they put the float assembly on the side of the tank for easy removal but not any more.Happy new year and thank you for your input.Jim

[@luisabad7538]

Joseph M ex ed exCarr ebb

[@PIANOSTYLE100]

jimthecarguy I know that there is the push to eliminate the diyer., but if a drain was so easy to drain gas would be stolen easier and cars would messed with .. so I'm going to side with the designers on this one. I was talking to a old mechanic and I mentioned that some of the foreign made gas pumps were very cheap.. he said look for ones that have a long warranty.. That made sense if it was sketchy they wouldn't warrantee it for years.

[@dannyhampton711]

joseph M because they won't be able to screw you at the dealership!

[@tomasgaspar8065]

Joseph M some cars have easy access to the fuel pump by removing the rear seats....ive seen them on kia rio, nissan altima, maxima, dodge nagnum

[@petrokrasnov2967]

A great video! Thank you.

[@SamC379]

My 05 Ranger cranks and wont start, but i let it sit for an hour or so and it starts up. Whats up with that ?

[@thatslow2v686]

Samuel Adams my 94 gt does the same thing

[@fliguy41]

My 07 f150 does that especially when its been ran awhile Only when its hot does it do that

[@spagsketti]

on the distributor is a module that is gray in color that will go out and on occasion will intermittently cause that issue. Most of the time it will just not start but if you are lucky it will be like I described. Also you have a fuel cut off that malfunctions. My 1985 Ranger I got for $500 because the switch broke and left the old man stranded. I eliminated it and spliced the wires together.

[@iiatargetanalyst3046]

Lose wire to relay or fuse arched wire aka grounded wire cause this. Could be any number of things like Loose battery cables to starter to alternator or Eroded battery cables need replaced. ECM fuse may be faulting work not work off and on

[@Rod-vj6dd]

i did all that testing except the injector diod testing. but i have fuel pressure at the rail an i have spark at the plug boot. my ex sister inlaw said when she got in it started good. than oil pressure guage started to fluctuate an sounded like it was gonna stall so she gave it a bit of gas an it just died. than she an i tried turning it bak on an nothing. it is my work truck. i work construction an im a foreman. i need my truck for work. please help

[@venomx4093]

You need to check the injectors, then check the fuses and relays. If all is good, check the compression and timing. If it doesn't crank at all, then checking the timing and compression isn't going to work.

[@Rod-vj6dd]

I got it. Was the fuel pump. But odd thing was I had pressure at the fuel rail. But it's all good. Thanks for the info

[@michaelgeruldo394]

Sir, i have related problem my r33 RB25det, when i started the engine & warming up suddenly shut down my engine. when i started up again my engine having Crank normally but wont start... there complete ignition of coil pack and new spark plug, and also checked already the fuel pump and fuel filter are working good condition, so will you give m,e advic

[@jimthecarguy]

Did you check for codes?Did you check fuel pressure?

[@michaelgeruldo394]

yes sir fuel pressure i have but the codes not yet

[@iiatargetanalyst3046]

michael geruldo Pull crank shaft sensor [sensor a clip behind pullys where belt is above water pump to the upper left. Use a mirror find it] clean it with electronic spray only both ends two squirts. Check ECM fuse too if its blown it cause what ur saying. Always check fuses relays sensors first work back. Use test light it save hundreds avoid replace parts dont need to be replaced