EP.28 DT Swiss 240s Rear hub service

[@김석완-e7g]

정말 고맙습니다... 이렇게 상세히 허브 베어링 정비 동영상을 올려 주셔서 전세계에서 최고의 영상 입니다.. 새해 복 많이 받으 십시요 ... 대단히 고맙습니다.....

[@schilhartrobin]

1) You forget to put the washer back under the ring nut requiring special DT Swiss tool HXTXXX00N5027S. 2) Do NOT use dense grease for the ratchet (probably Motorex 2000 in the video). DT Swiss Special Grease is required (TP-42 + 5%mineral oil), which is even thinner than Sram Butter..

[@dvdwillingtons1266]

Thank you very much for this excellent video.

[@thelampire]

There are 28 comments, but nobody mentions that the process you are doing is completely faulty. Once you hit the inner race of the bearing with a hammer, it's scrap. The removal process is spot on, the install process is spot on, but you don't re-grease the bearings after you take them out. You throw them in the trash and put in new ones. You could re-grease the bearings without taking them out, if you really want to do that. (If you have put in some sort of special grease in brand new bearings, I guess that's ok, except for removing it with a blade.)

[@quintusblack9112]

The remark is correct, but beside this the entire process was well done. The sharp cutter blade may also cut the rubber sealing, so a better approach is to use a sharp conic tool or a flat and very-very thin screwdriver.

[@quintusblack9112]

One can use the bearings that were pull out by using the press but not the one pulled with the hammer removal tool

[@cervgda]

Good luck with re-greasing bearing on the drive side (under the ratchet) :D

[@andymerrison883]

Would you really discard Ceramicspeed bearings at $200 each?? I certainly wouldn't go anywhere near them with a hammer.

[@thelampire]

Bearings are wear and tear parts, after a while you need to discard them no matter hpw much they cost. Ceramicspeed is a scam anyway, it's only better than the steel high quality bearings in the first 100km. It's quite good for bragging how much money one wasted on something lile a bearing, though.

[@iranacosta9942]

Qué herramienta uso para extraer los rodamientos quisiera comprar una igual puede dejarme el Link de comprar. Gran video felicidades

[@artgonzalez45]

Perfect! Those special tools though.

[@Marcelo_Harenza]

Perfect, tools kit complet, show every bearing, others videos show only freehub bearing, the more easy for change.

[@finallap2987]

Grazie mille fantastico lavoro 🔝

[@vivesinpermiso]

Muchas gracias amigo, me ha sido muy útil 👍👍👍

[@nyxsplitter7168]

Great tutorial video.Can you please share the link for the bearing press tool you use.Many thanks.

[@timeriderx]

When I see this much fine work I just want to grease it all up and put it back together and ride! It is not that bad and I live in a very dry climate. So now I will try to get it back together with just new bearings. Cost me $18.00. Oh Well.......

[@慎一郎二宮]

非常に参考になりました！

[@ukaszsl.6242]

What grease do you put into bearings?

[@bikereparo5358]

Parabéns sem falar nada você dia tudo, fiquei seu fã, parabens

[@hainman1]

Excellent breakdown on the process,im due to do my rear hub,with the ratchet system are the main hub bearings as prone to wear as the freehub ones?would the RRP kit be suffice to press bearings in

[@kyriacosvassiliou9385]

Καλημέρα από Ελλάδα. Πολύ λεπτομερής καθαρισμός, σε εμάς δεν τα κάνουν γιατί είναι χρονοβόρα διαδικασία και αναζητούν το εύκολο χρήμα.

[@jgbarre]

Excellent!

[@jorgemexf]

Goes to deep, the problem is I don't have many tools

[@gaetanocrispi1271]

Super video 👏👏👏👍🔝🔝🔝

[@simonwarmer8777]

Nice job&vid, but way too much and wrong crease on the ratchets?

[@TheGazavman]

Wooo nice job !

[@brackenlong3732]

Amazing i loving it

[@renemorale2094]

Exelente tutorial amigo

[@pinoybikers8834]

can you tell me what toolset i need in order to do that?

[@richardjeanneau303]

Hola donde consigo la herramienta para extraer los rodajes del hub? // Hello where do I get the tool to extract the shootings from the hub?

[@aleccejkraftcoff5145]

Hello! Thank you!

[@daclown3]

Is that steel bearing or ceramic bearing?

[@coverstem]

bearings as the same measures front/rear?

[@megearbikeshopd.i.y.2883]

DT Swiss 240 Bearing size 6803 for front hub Bearing size 6802 for free hub body (rear hub) Bearing size 6902 for rear hub

[@aynakolzincir3372]

@@megearbikeshopd.i.y.2883 Thank you!

[@Themilkmanskid.]

Type/name of grease used on the ratchets please? The engineering of design and fit of things like this always blows my mind!

[@Tntdruid]

DT Swiss Special Grease.

[@Themilkmanskid.]

@@Tntdruid I bought some. Looks nothing like what you are using in this vid.

[@BMWPROGRAMMINGJAMAICA]

Yo bro, omit out the seals band the hub wheel turn over faster without the seal rolling resistance.

[@ssirany]

what is your gold press bearing tool kit (name brand)

[@megearbikeshopd.i.y.2883]

ENDURO

[@zach_geale]

Anyone else have to mute the sound at the start of the video, due to their cats freaking out about the crying kitten? Haha 🐱

[@sergeykasparov3860]

what lube are you using? looks good. but you should always use DT swiss special grease for the rachets.

[@megearbikeshopd.i.y.2883]

I use Shimano premium grease for all cartridge bearing lubrication and also use for rachets too. Thank you for your advise.

[@anastasiospattakos6650]

@@megearbikeshopd.i.y.2883 the premium is still thick for freehub mechanisms. Shimano also has a specific freehub grease, I use this. The colour is more towards the white-yellowish.

[@HarryPotter-wm3kf]

Why are there first 5 bearings ??? and then even 6 bearings ?? I am confused ???

[@megearbikeshopd.i.y.2883]

During cleaning process is included front hub bearings.

[@davidecirillo6681]

hello sorry I wanted to ask you but where can I find a press like yours?

[@megearbikeshopd.i.y.2883]

The press tool I use is ENDURO or you can buy in many brand. Please see below link for ref . activesport.co/Enduro-BEARING-PRESS-F/-HUBS-AND-BBS th.aliexpress.com/item/32961453060.html

[@Joekow888]

Great video! What tools did you use to remove the bearings from the freehub body?

[@megearbikeshopd.i.y.2883]

I use enduro bearing extractor (someone call blind hole bearing tool set) to remove the freehub bearing.

[@balazsnovak81]

@@megearbikeshopd.i.y.2883 Dear friend, please give more exact details even manufacturer or link to this freehub body bearing removal tool. Thank you in advance!

[@megearbikeshopd.i.y.2883]

@@balazsnovak81 please see below link. soshanger.com/ENDURO-sealed-bearing-extractor-kit

[@александрнечаев-р3ц]

give the sizes of large cups(pancakes)

[@megearbikeshopd.i.y.2883]

OD 45mm / ID 35mm / H 45mm

[@ilyakonovalov3119]

Is this dt swiss tools? Or universal?

[@megearbikeshopd.i.y.2883]

All tools in the VDO are universal and some of them is DIY tool

[@lo_1]

As if the thread ring goes ou easy 😅

[@Tntdruid]

They never do 😂

[@SmileyBoy84]

Miau miau

[@edermariosanchez2120]

What are the measurements of the body bearings?

[@Алексей-ж3ч7ы]

MEGEAR BIKE SHOP D.I.Y. 4 месяца назад DT Swiss 240 Bearing size 6803 for front hub Bearing size 6802 for free hub body (rear hub) Bearing size 6902 for rear hub

[@edermariosanchez2120]

@@Алексей-ж3ч7ы thanks!

[@schnuppich]

Diese Sorte Lager hat eine Schmierfettfüllung, die reicht für die Lebensdauer des Lagers. Man sollte diese besser ersetzten und nicht öffnen.

[@tanks5261]

using a knife not a proper way to open the seal. It will damage the sealing

[@megearbikeshopd.i.y.2883]

Thank you for advise.

[@dangnation5378]

Lol another French mime video with no talking or subtitles.