SE is not spin error then. 5 E . Output error: check the filter. Your video was more useful than Samsung's website! Thank you.
@eSpares8 жыл бұрын
+gears5665 Thanks for the comment, hope the video has helped.
@shawnlucpicard5 жыл бұрын
Thank you so much all I had to do was open the drainage and clean it out. Thanks a million
@Ellerocks017 жыл бұрын
Thankyou so much for this video, I have had the 5E error code for months, thought I would have to get thee repair guy to come take the thing apart and clean the filter, i haven't been using it because of that. I didn't realize how easy I could do that myself, man it was full of dog hair I think.
@eSpares7 жыл бұрын
Thanks for the comments Michelle, remember to 'like’ the video if you enjoyed it or it helped.👍
@kylewenning50145 жыл бұрын
thank u. helped me fix it in less then 5 minutes.
@eSpares5 жыл бұрын
Hi Kyle, thank you for your post and glad we could help.
@manitarun24348 жыл бұрын
THANKS BRO we were confused with our error code and by watching this video we solved our problem
@eSpares8 жыл бұрын
+mani tarun You are welcome. :-)
@georgiafan66184 жыл бұрын
My washer displayed the “fN” code before dumping its entire contents into the washer pan below unit. Prior, we cleaned debris trap, removed, inspected and cleaned pump and it’s associated lines, cleaned door boot gasket/reinstalled spring assisted boot wire retainer. All appeared viable. Both Inlet Hoses replaced with braided SS. Unit ran well for 2 weeks until it dumped its water contents last night (pan prevented dire situation). Observed steady leak from bottom front panel, left side. We did clean detergent/softener drawer prior. I’m thinking boot gasket. What do you think? Thanks for video.
@happyboysngals96274 жыл бұрын
thanks buddy, you just fixed my machine (code 5E). subscribed.
@eSpares4 жыл бұрын
Hi happy boysngals, glad we could help and thanks for subscribing.
@nazikalgenied77646 жыл бұрын
Hi,my washing machine model no.WD0704REW make an errorF3E on its scr een and stops working after start.what is the solution
@eSpares8 жыл бұрын
Reply to Fred Morgan: Error 4E or 4C relate to a water supply or filling error. Check how quick it is filling and how much water is in the drum when the error is showing. If the water level is not reaching the correct level within a couple of minutes (slow filling) it times out and shows error. If the water is at a high level check the hose to the pressure switch as these can rub on the drum and make a hole. The pressure then escapes and the machine thinks it has not filled.
@anilkumar19718 жыл бұрын
Hi I'm getting error code 4C2? What is that? Is it anything serious with the washer? Its brand new washer (USA)..Please help..
@eSpares8 жыл бұрын
You have not given a make and model number, however on Samsung washers 'This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicate's course'. You may have to reduce your water temperature fed to the hot supply on your machine.
@anilkumar19718 жыл бұрын
MODEL NUMBER WA50K8600AV/A2 TOP LOAD WASHER..PLEASE HELP...
@eSpares8 жыл бұрын
Check that water temperature, you could try pouring some cold into the machine first as this may help if your supply is to hot for the machine.
@jenniferlove55667 жыл бұрын
eSpares and uui
@dsmatheny37904 жыл бұрын
Do you have a video on how to open the washer and replace the temperature sensor?
@eSpares4 жыл бұрын
Hi DS MATHENY, we don't currently have a video and we don't have your model details but most machines will have screws holding the top on at the back and an access panel on the back cabinet so start there.
@dsmatheny37904 жыл бұрын
@@eSpares Thank you sir. I hope you have a good day.
@eSpares4 жыл бұрын
@@dsmatheny3790 you too and please let us know how you get on.
@marciamunoz70746 жыл бұрын
Thank you thank you thank you thank you!!!!! You are my HERO!! I watched your video (several times lol) and got the courage to try and fix my less than a year old Samsung front loader washer. I couldn’t remember the error code my washer displayed so I did another cycle and saw 5E then went back to your video and saw what to try...omg I couldn’t believe what was in there!! Mind you I have 3 young kids. I found a baby sock water bottle caps nestle crunch wrapper and rubber bracelets. Oh and like 3 gallons of water! Hahaha! Then I turned back on (thank you for that safety step I would of completely overlooked otherwise) and I prayed it would work because I had all these wet towels now and PRESTO IT WORKED!!! Spinning like a Maytag hehe. And my boyfriend told me to call Samsung customer service for a technician visit Ha! No thanks I found and watched espares instead 🤗
@eSpares6 жыл бұрын
Hi Marcia, well done that's made my day that we were able to help you fix it yourself, remember to like the video and subscribe for even more useful videos.
@Estelle0011005 жыл бұрын
Hi! I need assistance please. Samsung error dE1? What is the problem? We did 2 test runs without any problem.
@dsmatheny37904 жыл бұрын
Thank you so much for the information. I really do appreciate your time.
@eSpares4 жыл бұрын
Hi DS MATHENY, thank you for your post and glad we could help.
@FredMorgan-18 жыл бұрын
Great video and very comprehensive, I just bought a WW70J3 machine and it keeps stopping with error code 4C. Checked all the pipes and water supply which all look fine. Cold water feed only. Any suggestions would be great....Thanks
@FredMorgan-18 жыл бұрын
+Fred Morgan Just came across some more info so looks like 4E = 4C
@eSpares8 жыл бұрын
+Fred Morgan Check how quickly the machine is filling. If this seems normal check the pressure switch hose is not blocked as the machine will not see the water level and shut down.
@FredMorgan-18 жыл бұрын
+eSpares Thanks for the comeback but now realise that the actual water pressure must have been too low. Previous machines have worked ok so thought that would this one be ok. Fitted to water main supply and now working ok
@eSpares8 жыл бұрын
+Fred Morgan :-0
@FahadAhmad-n9v5 ай бұрын
What model is it?
@danielwashington96655 жыл бұрын
hi I have a Samsung ww90j5456mw and when you put it on a programme nothing happens and it displays DC thanks
@non142007 жыл бұрын
Hey thank you for this great video , could you please tell me what is the solution with 8E error in my Samsung washing machine
@eSpares7 жыл бұрын
Hi Abdullah, this is explained at 2:02 (BE) and the problem is likely to be the control board.
@jessicali97734 жыл бұрын
Very good tutorial thanks
@eSpares4 жыл бұрын
Hi jessica, glad you enjoyed the video.
@aracelymoreno58595 жыл бұрын
Can you please help me, my Samsung DRYER is displaying DC?
@adamornelas18824 жыл бұрын
Hello! Do you have any advice or help for error code, "nF"? This is on a Samsung front load washer, model number WF316LAS/XAA.
@eSpares4 жыл бұрын
Hi Adam, error code nF means the machine has detected a problem with the machine filling up, check you are getting water to the machine and test the inlet valve.
@ask63785 жыл бұрын
Hello there, i search for " Samsung WF81F5E5P4W Washing Machine control board " any help ?
@djreaction17 жыл бұрын
NF1 is a popular one from my machine, but I didn't hear you mention that code, any help would be great! Thank you!
@eSpares7 жыл бұрын
Hi Richard, We believe this is a fill problem (possibly due to the hot water hose connected to the cold input). Check the water fills correctly by selecting a cold wash or rinse and it fills to the correct level in the allowed time (usually less than a minute).
@djreaction17 жыл бұрын
eSpares any ideas of why it only shows me the error code when it's on the bedding setting though? I did a quick wash setting and all went fine.
@eSpares7 жыл бұрын
Your machine will fill with different combinations of water depending on the cycle. Check your water supply is filling correctly and see another video for more information: kzbin.info/www/bejne/jISXaXqVmNx2jtE
@kiran11126 жыл бұрын
Hi Matt,how to access the motor in this samsung washing machine (b1245a) for checking carbon brushes.There isn't a removable back panel,do we need to use the shipping bolts to secure the drum before placing the machine on its side?
@eSpares6 жыл бұрын
Hi Kiram, do not use the shipping bolts just gently lower onto a soft surface. You can lower the machine down as shown in this video here: kzbin.info/www/bejne/rWqplWuEjL2UZqMm14s
@felixedgardosantia27695 жыл бұрын
thanks for your video. It served me a lot.
@eSpares5 жыл бұрын
Hi Ministro Felix Edgardo Santiago , glad you found our video helpful. Remember to like and subscribe for more helpful videos in the future.
@karinamanning95925 жыл бұрын
Mine was showing 06 or U6, don't remember. I turned it off, open the door but close was still very wet. What does it mean?
@debbiewilliamson25237 жыл бұрын
Hi Matt. Could you please tell me what a flashing red drum symbol means on my Samsung Ecobubble? Many thanks Debbie
@eSpares7 жыл бұрын
If the machine 'appears' to be working normally we believe the symbol is reminding you to do a tub clean. Check your instruction book for details on this.
@easyclearpool4 жыл бұрын
Mine currently will not unlock the door and unplugging it overnight and back in it is stuck on 13 minutes still and door continues to be locked once powered on. After 3 to 5 minutes of it nothing it says AE6 each time. Thinking about replacing control board, and see I'd I get lucky, any thoughts?
@eSpares4 жыл бұрын
Hi Berry, not an easy one to sort as the machine has detected an communication error between the main board and the inverter board, you will need to check the contacts and any signs of damage to either board.
@ayhancapan6 жыл бұрын
Thank you... So it was the filter. And i've fixed it as how you showed... Thank you...
@eSpares6 жыл бұрын
You are welcome Ayhan.
@jeffhollis53685 жыл бұрын
SAMSUNG WF306LAW/XAA SHOWS dr code , replaced the pump and checked hoses for clogs and still will not drain, what could the problem be? Thanks
@eSpares5 жыл бұрын
Hi Jeff, we can't find a dr fault code on the Samsung service site, can you hear the pump working? if yes then check the drain hose and plumbing but if no then test the drain circuit with a multi meter
@jessicaludivina30357 жыл бұрын
Hi... my Samsung front load washing mashing (WD146UVHJRA) doesn't give me any error code but it displays Hot and the lock symbol and it won't open the door... after a normal cycle of "quick wash" ... I didn't even used the drying ... could you please tell why is it doing it? And how can I stop it? Please!!! Thanks!
@Dk-de2ff4 жыл бұрын
Sir I lost my fan belt of Samsung front loaded washing machine and I can't find the model number and how I identify the model number please sir reply fast
@jennifiercools98666 жыл бұрын
This is an excellent video! My error code says E3, I just would like for you to spell the type of coil you referred to in the video. I googled how I thought it was spelled and got some vehicle car part. Thanks.
@jennifiercools98666 жыл бұрын
So I found in the comments you spelled it "tacko" coil. I followed the link you provided, but mine doesn't seem to have those problems described. I just put my Samsung front load washer model number WF56H9100AG/A2 in diagnostic mode (by pushing "spin, soil level, power" at the same time). Went to "TST" mode and immediately blinks "3E2". Any ideas? Thanks in advance.
@eSpares6 жыл бұрын
Hi Jennifier, the tacho coil fits in the motor usually at the top but you need to check it as it may just be loose, here is a link to show you the part www.espares.co.uk/search/ca1236/washers-and-dryers?SearchTerm=tacho
@jennifiercools98666 жыл бұрын
eSpares thank you!
@eSpares6 жыл бұрын
Hi Jennifier, no problem we are always here to help.
@mrsflash1007 жыл бұрын
I have a Samsung front loader WF1752WPC, This morning set it to a cotton load pushed start button and display panel board lights just started spinning around in three circles. I thought it may be a waiting to start thin but cycle didn't start. Any ideas? No codes came up just the spinning digital display on the timer panel.
@eSpares7 жыл бұрын
Hi Marion, many machines now 'weigh' the load by checking what power is needed to turn the drum. If the load was either heavier or lighter than the expected load for the cycle or giving unclear results (possibly a large single item tumbling unevenly) the machine may keep retrying to identify the weight. Try on a different load or a different cycle before assuming a fault on the machine.
@jenelynmahilum96795 жыл бұрын
hi....can u please tell me what to do with the machine cause it isn't working ...it appears DDC....What could be the problem?
@eSpares5 жыл бұрын
Hi Jenelyn Mahilum, it means the machine has detected the add wash door has not been operated correctly, make sure the door is closed and restart the machine.
@georgecarlson30337 жыл бұрын
Hi - I have a Samsung 8.0kg SW80SP top loading wishing machine with error dE - please help ! Ive read that this is a door problem but there are no locking mechanisms for top loaders
@eSpares7 жыл бұрын
The door may not have a lock but there is usually a switch that recognises it is closed. There may be a magnet on the lid on some models that can come off causing this problem.
@MariaHernandez-go8te8 жыл бұрын
I have a Samsung top loader washing machine. I am not getting any error codes but it is not washing. The door is locked and can't I get it unlock or start washing. Have you ran in to anything like this?
@eSpares8 жыл бұрын
+Maria Hernandez Many machines have a thermal door lock that prevents the door unlocking when water is in. Try unplugging the machine and waiting for three minutes. if this does not work see another video: kzbin.info/www/bejne/qV7CqWWqiNKXZqM
@hmdosti75207 жыл бұрын
Hi I have a Samsung washing top load it fills with water then shows 4E and drains right away
@eSpares7 жыл бұрын
Hi, this is where the machine 'thinks' there is a filling problem. If it is filling to the usual level (or above) just before the error check the pressure switch hose as on some Samsung washers it can wear a hole if it rubs on the drum during spin. For more information see another video: kzbin.info/www/bejne/aKGsh553rbyGjsk
@lxx67005 жыл бұрын
Fe code please tell me what i have to fixed thanks
@praveenbalodi44937 жыл бұрын
My Samsung wf8558nmw8 front load washing machine is showing error code Uc and Un. Can u pls tell me whats the real problem.
@eSpares7 жыл бұрын
Hi Praveen, this sounds like you have an unbalanced load especially if the errors occurred at the end of a cycle and the machine has either shook on spin or not finished spinning. For more information on balancing your washing see our video: kzbin.info/www/bejne/q3ylqmBvg6p5a6M
@doemugyvandoe72886 жыл бұрын
eSpares Uc code what is it
@darylhoskins56967 жыл бұрын
Please help , have not seen any other vids for code of LO door locked and will not open , Samsung stainless , power foam , steam n night wash
@eSpares7 жыл бұрын
Hi Daryl, if your door lock is a 'solenoid' type door lock (makes a loud click when locking and unlocking) turn the machine off then on again. As long as the handle is not loose select the spin cycle and start, then pause and when the machine double clicks 'bump' the door to try and help the lock release. For more information see another video: kzbin.info/www/bejne/qV7CqWWqiNKXZqM
@dianes80484 жыл бұрын
My front loader has a 4C2 error code and an alarm. Any ideas as to how to resolve this? Thanks.
@eSpares4 жыл бұрын
Hi diane, 4C2 means the machine has detected an issue with the water temperature, check the water hose is connected to a cold supply and test the heater.
@dianes80484 жыл бұрын
@@eSpares Thanks so much for your response. I have had this washer for almost 2 years and it has never done this. Thanks, again!
@himatullahkarokhil45056 жыл бұрын
Hello, can you you please tell, What does "b2" error code means? on samsung washing machine 7kg diamond.
@eSpares6 жыл бұрын
Hi Himat, B2/BE2 refers to a control button issue so check the buttons as they may be sticking.
@katerinaivanovska91157 жыл бұрын
hi I have Samsung diamond 6.2kg and I also have SUD error. what does that mean? thank you
@eSpares7 жыл бұрын
The error SUD is to indicate an excessive amount of foam or suds in the drum. This can be caused by too much detergent or a build up in the machine. . If this happens run a rinse and spin cycle and reduce the detergent quantity on future loads.
@thehardtailhero695 жыл бұрын
Relating to an LE code, how might I find the leak and where is it probable to be?
@eSpares5 жыл бұрын
Hi The Hardtail Hero, make sure you check the level of the drain hose first as if it's too low it can cause the error code, if it's a leak there will be signs of water on the floor underneath or at the back and water trails may indicate where it's coming from.
@mitzimatsumoto39936 жыл бұрын
Is it possible to put a video on Panasonic washing machine??
@eSpares6 жыл бұрын
Hi Mitzi, we will try and produce a fault code video for Panasonic machines in the near future.
@waveyynishlmg3994 жыл бұрын
What does dC mean?
@keithmitton45589 жыл бұрын
I have a Te2 error appear on my machine display. You haven't identified how to fix this issue in this video. Can you please provide me with some insight and some instruction.
@eSpares9 жыл бұрын
+Keith Mitton We believe TE2 is a temperature sensor error so check the NTC sensor on the heating element and the wires/connector. If you cannot see a problem it is possible the sensor is faulty and would require replacing..
@keithmitton45589 жыл бұрын
thanks for that... where would I find thw sensor. Is there a diagram I could look at
@eSpares9 жыл бұрын
+Keith Mitton We do not have a circuit or diagram you can access but we have a video showing the sensor when replacing the heater at: kzbin.info/www/bejne/pWHdfYeqeMeeodk
@kristimontgomery62337 жыл бұрын
My samsung front load washer is displaying the error code EE, but the top portion of the first E is missing. What does this mean?
@eSpares7 жыл бұрын
Hi Kristi, the only information I can find on this error indicates it may be a eeprom error (the control board programme memory) so it may indicate you need a new control board.
@moaathalmaani30585 жыл бұрын
God bless you that was soooo useful
@eSpares5 жыл бұрын
Thanks Moaath, glad to know you enjoyed this video. Remember to like and subscribe for more helpful videos in the future.
@reissmason19908 жыл бұрын
hi great vid i have a samsung ecobubble with SUD code how do i fix this please?
@eSpares8 жыл бұрын
This is caused by to much foam from excess detergent. Use a washing machine cleaner like: www.espares.co.uk/product/es1566874 and then reduce the detergent used.
@neil_digital5 жыл бұрын
Could you let me know where the SUD sensor is in the Samsung ecobubble
@hhhhhjjj2345 жыл бұрын
thank you for your video you forget to add in case of 5E code it could be the sewage pump. after checking for clogged filter then the blockage in hose . to dismantle this pump we schould remove the front panel all you need is screwdriver, remove the door seal also , the pump is the right bottom , chech the inside hose too
@eSpares5 жыл бұрын
Hi Gadouche Brahim, thanks for the post and helpful comments. We have mentioned 5E error code at 1:05. Thanks for tuning in.
@hhhhhjjj2345 жыл бұрын
@@eSpares yes i know thanks to your video i have just repaired mine a samsung wd j1255 5E error code i changed a new drain pump and it was ok the electric resistance was good i powered the pump it works guess what ? the pump was weak under load when i filled the drum it stops from time to time and if you rise hight the drain hose the pump won t work so if you find the resistance good it doesn t mean the pump is good
@eSpares5 жыл бұрын
Hi Gadouche Brahim, thanks for your comments. Glad you were able to fix your appliance. Well done :)
@imanmk5315 жыл бұрын
Hi I need your help in error code lc1 for Samsung washing machine
@eSpares5 жыл бұрын
Hi Iman MK, error code LC1 means the machine has detected low water levels inside the machine, check the drain hose is not too low which can cause syphoning and make sure you haven't got a leak which will cause it as well.
@Yaz2id7 жыл бұрын
THANK YOUUUUUU MATH
@eSpares7 жыл бұрын
😊
@aviewfromsouthafrica26805 жыл бұрын
Hi there, please assist me, I have an "OE" error on my samsung. I noticed also that the water level was very high at some point inside the machine
@eSpares5 жыл бұрын
Hi A view From South Africa, OE refers to the washi9ng machine has been unable to drain the water during the wash cycle, check the drain hose, filter and drain pump.
@carlabozzano7 жыл бұрын
Thanks for your videos. Please, could you tell me how to sort out the error Uc on Samsung WF0700NCW? Thanks again.
@eSpares7 жыл бұрын
Hi Carla, error UC is a voltage supply error and may be caused by a 'bad' connection to the electrical supply. Check it is not UE error as this is a balanced load problem.
@carlabozzano7 жыл бұрын
eSpares Thank you for your answer. I have already checked the balance of the load in it. I clean all the filters, emptied all the canes, changed the connection of the power supply and still persist the problem. Also, I re-calibrated the machine. In any case, I am thankful for your answer. Keep it up ☺
@eSpares7 жыл бұрын
Your problem could be a loose connection anywhere from the machines power switch to the fuse board. If it is a poor connection it is likely to occur when there is an increase in power used ie when the machine heats or spins. This may even show if you plug a light into the socket next to the machine as it may cause a standard bulb to flicker if the power is the problem.
@carlabozzano7 жыл бұрын
eSpares Ahaaa! You are right, because, most of the time, the machine stops after heating the water or spins.. What should I do? Shall I call a technician? 🤔
@eSpares7 жыл бұрын
You may need a house wiring technician not an appliance engineer. Can you try the machine on a different power point?.
@bijeeshkk48165 жыл бұрын
I have wf b1061 2 E error wt the problem and how wil..
@mdavis0868 жыл бұрын
I have a Samsung wf330anw/xaa with a LO error code and keeps locking as soon as you close the door and keeps triggering the lock like 7 times and comes up with LO code..any info would be great..
@eSpares8 жыл бұрын
Check nothing is stopping the latch locking the door and replace the lock if required.
@kamalayash87918 жыл бұрын
Hello. I have samsung WF1602W5v and its showinng (SUD)..how could we solve it? thanks in advance..
@eSpares8 жыл бұрын
+Kamal Ayash The reason for a SUD error is the machine has detected to much lather. This is likely to be due to excess detergent or the wrong detergent type (must be for 'Automatic or HE high efficiency machines). If using the right detergent run your machine empty with a washing machine cleaner product to remove detergent build up and reduce the amount of detergent you are putting in.
@blakeriley35907 жыл бұрын
Just had a repair person out to fix the latest recall - when he left he started a self clean cycle then it stopped and there is an error code flashing SC - what's wrong ?
@eSpares7 жыл бұрын
The SC is likely to be the fact it is in a Self Clean cycle as this is not a recognised error code. If EMPTY you can check the pump filter is clear (use a towel or tray for the little water in the pump). Then if the cycle has finished switch off and restart with a 'test cycle' on a short wash to see if it has a problem.
@rafiaabeke38996 жыл бұрын
my Samsung washing machine WF1124 showing 8E pls show how to replace the sensor.
@eSpares6 жыл бұрын
At 2:02 we say 'Now if your machine is displaying EB all BE this is a motor triac error. And this is normally to do with a fault in the control board. We do not have any other information on replacing this part.
@butterflyzavala787 жыл бұрын
hi thank you for sharing this information but my washer show it like mesajes not like codes in my case sometimes show sd or sud msj please if you can help me I will appreciate your comment.
@eSpares7 жыл бұрын
Hi Blanca, your machine is showing sud to indicate there is too much foam from excess detergent. Run a rinse cycle and use less detergent on your washes and the problem should be resolved.
@butterflyzavala787 жыл бұрын
Thank you so much 👌
@eSpares7 жыл бұрын
😊
@eSpares7 жыл бұрын
Your Welcome.
@georgiahirakis2706 жыл бұрын
what about error door open, we order a new latch for the door it was replaced and it still says door is open any suggestions?
@eSpares6 жыл бұрын
Hi Georgia, if the machine is showing a door error then check the door lock.
@henryxavier37514 жыл бұрын
Thank you E3 👍
@eSpares4 жыл бұрын
Hi Henry, E3 means the machine has detected an overflow issue which is usually caused by too much detergent in the system.
@henryxavier37514 жыл бұрын
Thank you
@dsmatheny37904 жыл бұрын
What does tE mean and what does Cb mean sir?
@eSpares4 жыл бұрын
Hi DS MATHENY, tE means the machine has detected a temperature sensor error so test the sensor with a multimeter, Cb is for calibrating the weight sensors in the machine which has probably been activated by mistake.
@FaaTi7 жыл бұрын
wd90j6400ax Shows LC1 just as it draws water bought only a week ago?
@eSpares7 жыл бұрын
LC1 error is indicating the machine has low water level (it has not filled to the correct level in the allowed time). Check the water supply is turned fully on to the pipes and the hose is not trapped. Also check the drain hose is not lower than the water level in the drum or the water may be running out as the machine fills. For more information see our video: kzbin.info/www/bejne/jISXaXqVmNx2jtE
@erastongamilaga80158 жыл бұрын
Hi my washing mashine is samsung 16kg it has probrem water overflow over the soap drawer I dont know what could be the probrem .please support
@eSpares8 жыл бұрын
This usually happens if too much powder has blocked in the hose to the drum. Check and clean if required.
@paulsingh29128 жыл бұрын
I have a Samsung washing machine type WF1124XAC 12 kg I turn on electricity Switch on the power switch It gives display Accepts the washing programme After placing clothes and open the water tap when I press start does not work Stay for two minutes and then appears on the screen - Voltage Control - U/C call for service What should I do and what is the solution?
@eSpares8 жыл бұрын
The error suggests there may be a problem with the electric supply to the machine. Disconnect the supply and check the power connection and wires are all tight and not arcing or burning.
@kitkatwelshlady84656 жыл бұрын
I am getting a flashing 3E or 33?? drum is shaking not washing clothes at all after 25-30mins?? 🤔
@eSpares6 жыл бұрын
Error 3E is a motor 'tacho' error. this is a coil or sensor on the motor that identifies the drum speed as it turns. Check the motor connections and see our video: kzbin.info/www/bejne/emakqGp5d6p6hqs
@wahyuroberts23308 жыл бұрын
Hi.. I just bought washer Samsung WA45K7600A/WA45K7100A.when I tried to used for the first time during after the spin the machine was drain but the water filled again and has code Ur..what should I do?
@eSpares8 жыл бұрын
We do not recognise an error UR but UB refers to a balanced load problem. For more information on that see our video: kzbin.info/www/bejne/q3ylqmBvg6p5a6M
@sergiomaunze33928 жыл бұрын
I have a problem with my samsung washing machine WF8500NHS It starts then after 3 minutes stops and shows a lock,please how can I take the lock off?
@eSpares8 жыл бұрын
To release the child lock if it has accidentally been set press and hold the spin and the option buttons together for over two seconds. Pressing again for two or more seconds will turn it back on.
@mystylemystyle1985 жыл бұрын
Thank you so much
@mystylemystyle1985 жыл бұрын
My machine showing b62
@mstinamichele8 жыл бұрын
Our error code is nf. I understand this is a filling error as well?
@eSpares8 жыл бұрын
+Tina S. If the machine is filling but you get NF then check the hose to the pressure switch. If it is not filling check the valves and water supply. See our video: kzbin.info?o=U#
@christopherhollinger63954 жыл бұрын
What is a 3C code?
@shrekas29668 жыл бұрын
i have a problem on samsung ww60j3083lw/le i think its a code 4h. it wont take water. maybe its something with water presure but i use open water source that has alot of presure becauss when i take off hose it just bursts water so the presure is fine. it has something to to with water taking into machine itself because it operates without water so i turn it off.
@eSpares8 жыл бұрын
+Shrekas 2 Thanks for your comment, we recommend you have a look at our diagnosis video: kzbin.info/www/bejne/jISXaXqVmNx2jtE
@MdIqbal-tc4jb5 жыл бұрын
Thank you sir
@eSpares5 жыл бұрын
Hi Mohammed, thank you for the post and you are very welcome and have a lovely day.
@sasacvetkovic1277 жыл бұрын
I am having no error code. Machine is working normaly than from 9 minutes goes to 10 than to 9 and like that until eternaty. It may happen on 31 min, etc... Any solution?
@eSpares7 жыл бұрын
Hi Sasa, If the machine is washing normally it may be when it gets to the heating that it then starts to recalculate the time due to it, not heating, you will need to test the heater first and we have an advice article and video to help www.espares.co.uk/advice/symptom/washing-machine-is-not-finishing just copy and paste into your browser and let us know how you get on.
@Fernando-ew6eo7 жыл бұрын
Hello my washing machine samsung eco bubble presents the following error code ss 3 1400 and orange padlock flashing greetings and thanks
@eSpares7 жыл бұрын
Hi Fernando, we can't find any ss3 error listed, however it sounds like the child lock may have accidentally been activated. Look at the controls for an image of a child's face or a padlock with marks to two buttons. By holding the two buttons at the same time for 5 seconds it should release the lock if this is the case.
@AKCenglishbulldogs7 жыл бұрын
My washer has the hour glass icon on... and seems to be frozen.. it doesn't let me select a different cycle, or start... do you know what the problem is?
@eSpares7 жыл бұрын
This usually is indicating it is weighing the load as the drum rotates. Give us the full model and we may be able to help further.
@AKCenglishbulldogs7 жыл бұрын
SAMSUNG wf42h5200AP/A2 --- Thanks! :)
@eSpares7 жыл бұрын
Try calibrating as shown in the instructions: For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps: 1. Turn on the washer. 2. Press the Temp. button and Delay End button simultaneously for at least 3 seconds. 3. Remove any contents in the tub and close the door. 4. Press the Start/Pause button. 5. The drum rotates clockwise and counterclockwise for approximately 3 minutes. 6. When Calibration Mode is finished, the “En/End” appears on the display and the washing machine turns off automatically. The washing machine is now ready for use.
@HS-re7dw8 жыл бұрын
Hi! i 've seen ur video of HE1 which concern heater ,but i have this prob by even using cold water .why so
@HS-re7dw8 жыл бұрын
I forgot to mention when the machine is stopped and started again it usually does not stio.Thank you
@eSpares8 жыл бұрын
+Hamish Sampai It is likely the heater is failing or it has resistance to ground. This could cause it to be intermittent.
@HS-re7dw8 жыл бұрын
Thank you very much for ur response!
@eSpares8 жыл бұрын
+Hamish Sampai :-)
@sonjaemery8 жыл бұрын
The error code I get is 8e. Any ideas would be great. Thx
@eSpares8 жыл бұрын
This sounds like BE not 8E and that is likely to be a PCB problem see 2:02
@crisrx777 жыл бұрын
Sonja Emery did you get your washing machine fixed
@merrilljohnson9376 жыл бұрын
eSpares
@rolfwolter50265 жыл бұрын
please what is "LC -1" ? (its blinking "LC" and "-1") of my samsung ww80j3473kw
@eSpares5 жыл бұрын
Hi Rolf, it means the machine has detected low water levels in the machine, you will need to check the drain hose and make sure it hasn't dropped causing the water to siphon out. You should also check for a water leak.
@rolfwolter50265 жыл бұрын
@@eSpares directly on start bevor water come in? Th answer from service: " -Water loss at / below the unit - Microswitch defective due to moisture - Sensor triggered by a lot of moisture" You know where ist the sensor /Microswitch of LC1? The sensor in the base, inside on the floor panel, I removed it, this can't be the reason. No water leak, inside is it dry
@eSpares5 жыл бұрын
Hi Rolf, thank you for the information ☺
@rolfwolter50265 жыл бұрын
@@eSpares I found the error source of my "LC-1". The water-/pressure sensor st-545 is the problem! If I remoe the tube + conect another short part and I suck it (I meah the lower water level) all ist fine, without suck or blow in, I have the LC-1 Error. Maybe its helpful for U. best regards
@takotako80906 жыл бұрын
Hello , my samsung error code is Sud what it means ? Please help me , what can I do?
@eSpares6 жыл бұрын
This is too much detergent (suds) so reduce the amount used and run a rinse cycle on the machine before using it again.
@backdarxkmgamingxx81198 жыл бұрын
I have a problem Samsung washing machine type WF1124XAC 12 kg They work well Now do not accept any order panning After placing clothes and open the water tap And operation of electricity And operation of the power switch do not work Stay for two minutes and then appears on the screen - Voltage Control - U/C call for service What should I do and what is the solution? T.U
@backdarxkmgamingxx81198 жыл бұрын
+eSpares Thank you
@eSpares8 жыл бұрын
+albahr m :-)
@broshak93845 жыл бұрын
I have a 3c2 code will drain and fill, tub will move slightly while filling but once filled stops moving and sits there
@broshak93845 жыл бұрын
Also motor tests fine and as I manually spin the drum I have signal from the sensor
@eSpares5 жыл бұрын
Hi lsxroshak 12, Samsung do not list 3c2 in their error codes but everything starting with 3 refers to the motor or motor PCB.
@mffdesigner7 жыл бұрын
I got a WF328AAW/XAA which was showing error ND. I called a technician. He suggested to change the control board. How I changed that and it's showing error E3. What do you suggest? Also I didn't see this error code on this video. Tks.
@eSpares7 жыл бұрын
Hi Marcos, "E3"could mean the door is not closed properly. Either there something preventing it from closing properly (blockage) or there is a fault with the locking mechanism.
@eSpares7 жыл бұрын
If that does work try a machine reset as follows: 1. With the power on press and hold down the start button. 2. While still holding the button down turn the dial one click anti-clockwise (15-minute cycle on mine) 3. If it shows '8888' on the display then skip to step 5 if it shows 'E3' turn the dial back to the off position. 4. Press and hold the start button down and again turn the dial one click anti-clockwise (15-minute cycle on mine) 5. With '8888' now displaying hold the start button in for 1 minute. 6. Stop pressing the start button. 7. Return the dial to the off position.
@israelsanchez28918 жыл бұрын
Hi great video, the display of my samsung machine marks E3 what is the problem there?
@eSpares8 жыл бұрын
Your error is indicating the control board cannot identify the motor turning. If the drum does not move check the motor brushes. If it spins fast and stops check the wires on the coil on the end of the motor.
@jorgedeleon96854 жыл бұрын
hi, I changed water pump,but still not draining,what should I do
@eSpares4 жыл бұрын
Hi Jorge, was the drain pump faulty? the usual checks are the filter, drain hose and plumbing blocked stopping the machine from draining.
@jorgedeleon96854 жыл бұрын
@@eSpares shows this error bE can you help me with this
@Fa6aMiTheAdubber8 жыл бұрын
I thought I saw 'SC' on my washing machine (WF602U0BHSD) but I can't seem to find anything about it and so I assume its 5E since I know the door won't open since it's full of water
@eSpares8 жыл бұрын
The error 5E is a drain error and is likely caused by debris in the drain pump. Lower the drain hose to a shallow bowl to let the water run out and when empty pop a towel under the filter at the front. You then can take out the filter and remove any foreign objects.
@jasonthacker21584 жыл бұрын
How do I fix code CL6 ?
@srishtisingh86207 жыл бұрын
hi, my machine is not showing any error..it is showing 69..but red is indicating just below lock indicator..wat can be the issue?
@eSpares7 жыл бұрын
Hi Srishti, we do not recognise this problem symptom. The best way to identify what is going wrong is to watch some of our diagnosis videos to establish what parts of your machine are working. For more information watch this video: kzbin.info/www/bejne/h4qzoqOggbtqqZY
@lupesalinas21234 жыл бұрын
The screen show a key And a T-shirt, what’s the problem.
@eSpares4 жыл бұрын
Hi lupe, Garment + The t-shirt with a + icon indicates you can pause the cycle to add more clothing.Some front load washers have an Addwash door which makes it even easier to add more clothing during a cycle.
@Neophoria8 жыл бұрын
Thank you
@eSpares8 жыл бұрын
+mohammed j :-)
@annrodriguez24607 жыл бұрын
please help. my washing machine is giving me an OE code. i did what u said and its still doing it.
@eSpares7 жыл бұрын
DE is a door error have you replaced the door lock?.
@lupesalinas21234 жыл бұрын
Is not pouring water when it supposed to
@فوفو-ه1ف9ص6 жыл бұрын
My washing machine model WD0754W8EH Show me code error FE, what's problem and how can i fix it ? Help me please,,, Thanks...
@eSpares6 жыл бұрын
If this is a washer dryer check the drying fan motor turns freely and runs correctly.
@ranjitdas24257 жыл бұрын
My samsung washing machine wf f-861 did not work in day time .. its auto matically shut, dont turn on same time , some time later i can power on the machine but after few swc its a agian power off automatically,, but its a proper work in night time with out any problem .what can i do sir..
@eSpares7 жыл бұрын
Check the power connections are not loose as this suggests a power fault. Is the electricity supply good?.
@mastertry19357 жыл бұрын
My Samsung Washer loads up with water first then after few cycles, it stops and motor seems to hum instead of putting in more water. Then it shows LE error code and nothing happens... WHY IS THAT??
@eSpares7 жыл бұрын
LE is the machine thinking the water is not at the correct level. If your machine has two fill hoses (hot and cold) the machine may initially fill with cold then open the hot and have a problem then time out with LE. Check both supplies if fitted.
@EL_C0N3J07 жыл бұрын
Hi Fernando My Samsung Top Load Washer Model WA40J3000AW/A2 and am having a issue It makes a gear grinder sound during the wash cycle grinds and stops and grinds and stops and so on.. I've tried it with and without clothes and still the same The Ligth(Normal/No bedding Cycle) flashes on and them of and so on...it sounds like he tried to spind but stops also stays full with water inside, I check for any dirty stuff but is clean Need help Thank You!
@eSpares7 жыл бұрын
Open the door and try rotating the drum. If it is catching or grinding it may have something stuck between the drum and tub. We are not too familiar with this machine in the UK but believe there is a bolt in the centre of the drum that once removed may allow the drum to be taken out and anything caught under accessed.
@EL_C0N3J07 жыл бұрын
OK First of all Thank You for helping me, I did what you ask me to do I open the door and I spin the drum with my hands and sounds ok no noise but I forget to tell you that the company did the Re-call on this Washer machine few moths ago after that they send me some service repair company (Because the warranty) And this is what they did. On the First visit they replace the Main PCV, Called CX back after a Cycle. According to them shows this : Defect Code ARCS , Also Repair Code CR01 Factory Modification.(Repairs were made no change) The second visit they Replace Main PCB,Condenser, and Dampers According to them shows this Defect Code APPR and also Repair Code ALEL Aligment, Electrical. (Repair were made no change still the same) On the Third visit they replaced Clutch and Motor according to them shows this Defect Code DISP and also Repair Code ALME . Repairs were made no change still the same until now all this information i got it from theirs Service Orders they provide me.
@eSpares7 жыл бұрын
I thought this was a 'new problem' not something that has been ongoing. As we previously stated we are not familiar with this model but it appears to be direct drive drum. On wash if the noise is still present it is likely to be a main motor problem or drum bearings/suspension. If the problem occurs when emptying i is more likely to be a pump related problem. Sorry we do not have more information to narrow it down more than this.
@EL_C0N3J07 жыл бұрын
Understood ... I checked the pump is clean and working this issue happens in between 2 o 3 Min after we put the washer machine to work on normal Cycle flashes and not move the noise i heard is like the motor try to work for one second and cant make it and so on . But thank u for your help!
@roamrioedwards45288 жыл бұрын
hey my machine is showing like a reverse 6 or upside down p can you explain that one?
@eSpares8 жыл бұрын
+Roamrio Edwards If the machine isnot starting check the door lock as the machine may be indicating d for door lock.
@roamrioedwards45288 жыл бұрын
+eSpares No its not the door because when the machine is filling up the water it just stop I think it's the motor problem you talked about in the video
@eSpares8 жыл бұрын
+Roamrio Edwards To help identify your problem have a look at our diagnosis videos: kzbin.info/aero/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ
@roamrioedwards45288 жыл бұрын
+eSpares. Okay thanks
@maffoo89617 жыл бұрын
My samsung dryer has t0 or tO and I'm not completely sure what it means
@eSpares7 жыл бұрын
Hi Mathew, we believe this is a dryer sensor that has failed and requires replacement.
@raymondelledge92526 жыл бұрын
Mine shows an nd code even after I cleaned filter drain runs a cycle an stops with water still in it and won't wash