Axial Wraith - Upgrade your Axial RTR Wraith vol 2

[@CromagnonCommando]

You're gonna get me to buy this dang Wraith Kit I keep seeing and hearing so much about. I am anxious to see the third video with the Upgrade Progress. Will keep watching and keep up the good videos. I only recently got into R/C and have already picked up a couple of tips from your episodes. The Rock Crawlers I have are nothing like this Wraith. I want to get into Scale now instead of just ROCK CRAWLING.

[@EvolVillainRC]

@CromagnonCommando HA! Damn I need to make some commission from Axial for selling kits for them..lol Yea the Wraith is cool for sure. It's kinda scale, but it's kinda more of a basher, but it's 100% fun. I was actually thinking of shooting vol3 this weekend if it's nice out. I got all my links in, I just need to install them.I appreciate you watching and I'm glad I can help out here and there:) Get a scaler, you wont regret it!, that is unless the wife finds out!

[@EvolVillainRC]

@450hp202turbo Good stuff to know! Thanks for sharing that. I hoping with a properly setup slipper I wont have any transmission problems since that's what it's there for. I'll post up if I have any issues.

[@EvolVillainRC]

with brushless you always gear by temp, but you can use a chart to get at a starting point. This is my friend Josh's thread on RCC. It's pretty much the Wraith Bible. rccrawler*com/forum/axial-wraith/346212-choosing-motor-esc-your-wraith-gearing-added.html replace the * with a .

[@EvolVillainRC]

@Hillingdonway The stock pins will not work. The MIP's are much more heavy duty so they (the grub screws) are much larger. I had the exact same thought and was dissapointed when they didnt work. As for tools these i'm using here are Dynamite.They have a hardened tips which have been holding up pretty well to me torquing on them. Stripping grubs probably means the tool you're using is worn or doesn't fit properly. I have never stripped one, just snapped tips off of allen drivers.

[@EvolVillainRC]

It's a Kimbrough. Should be all over ebay. I think I picked mine up at CKRC.

[@450hp202turbo]

i have the same motor ecs 13.5 the gear box striped out fast , so i fitted a Hot Racing billet alloy all metal gear gearbox shafty.com sell these custom main shaft allows you to run a Robinson racing 32p slash rwd steel v3 slipper clutch. and pinion ,steel drive shafts from rc4wd .axial stronger diff gear set = bullet proof wraith , the noise is not bad from steel spur

[@EvolVillainRC]

@stardocker haha its not snowing here, just cold and wet! send your parts list on over!

[@EvolVillainRC]

I do, I just added a link in the notes.

[@PowerhouseOffroad]

Thanks evol! Nice vid. Could you use the stock axial through pins and shave the length to stop them from bottoming out on the mip's? Almost a half lock? What tools are you running there for the pinion grub? You mentioned torquing down on it. I've always had problems stripping the grub. Any thoughts?

[@TheFordf650]

hi saw those hex drivers that you used with your drill not the red one but the 4 in the case. where did you get those i have been looking for those forever. thanks

[@Traulus83]

nice rig man,but wanna know what spur is that?

[@benmara8139]

Sorry for all the questions, just getting back into RC after 10yrs. Im slowly building my wraith to brushless, how did you come to the ratio of Pinion and Spur geard?

[@EvolVillainRC]

@rezra38 No I usually shop at RPP, TCS or just on ebay.

[@stardocker]

Hey man in kuwait its not snowing at all you can send it right over and ill test it. Just kidding. Im ordering mine in 10 days i gotta parts list imma message you. I want you thought on them and what else I should get.

[@Traulus83]

i figured that,i have found the pinion on amain,but i didn't find the spur.who is the producer,or do u have a product # ?

[@bobaque70]

Great video once again!can you please give me m.i.p driveshafts part number for the pair front and rear for wraith.i can only find individual and hobbyshop cant find any listing at all

[@EvolVillainRC]

www.miponline.com/store/mip11116.html

[@EvolVillainRC]

@TheFordf650 They are made by Associated. I picked mine up at my local Hobby Town, but just Google Associated Factory team hex driver bit. I've seen them from amain hobbies to ebay. They are like 25 bucks but an investment well worth the money!

[@Dbigpinoy]

The 56 tooth 32p Kimbrough spur is no were to be sold

[@EvolVillainRC]

55T 32P

[@stardocker]

SEnt already lol Darn almost had it.

[@benmara8139]

Do you have a build thread of your Wraith?

[@craigtreeguy]

It's of a slash 4wd

[@TheFordf650]

@ev0lash That so much just bought a pair for $20