HOW TO DELETE GRID HEATER ON 6.7 CUMMINS

[@UpNorthDiesel906]

👍👍

[@EVERYTHANGDIESEL]

UpNorthDiesel thanks man appreciate the support!

[@jasonbullis9256]

I know it’s an old video, but I watch a lot of the videos you post. You do great work to help guys like me work in our trucks. Keeping more money in my pocket…

[@natebowen3959]

Thanks for the help on this video. I just did my grid heater delete and your video helped me know what I was getting into. Knocked it out no problem. Thanks again

[@philmontana6847]

Catch can, grid heater delete, some more leds for the bed, and a wiring harness for 5th wheel coming up this weekend yooooo!!!! Oh yeah and CCV delete. ALL THIS BECAUSE I WATCH YOU MY MAN!!! Thanks sooooo much for being REAL!

[@EVERYTHANGDIESEL]

No worries man! U got a lot going on

[@philmontana6847]

@@EVERYTHANGDIESEL thank you.

[@dannywilliams7917]

I used your video to do my install. Made it faster watching yours lol. Good video man

[@EVERYTHANGDIESEL]

Danny Williams glad it helped your install! No one had a how to video on KZbin figured I would do one haha.

[@jonathanlaskiewicz2841]

Just finished up my grid delete, but added a throttle valve delete with heater. Although it was far from easy and I have a leak on my rail in the back. Praying it isn't cracked. Thanks for the video and for your service. Happy 4th of July

[@mannyguerra320]

Very informative video, helped me out a lot doing my install. Thank you! Keep doing what you’re doing brotha

[@EVERYTHANGDIESEL]

Glad to help! Thanks for the support! 🙌🏽

[@KidinDaBassement]

Hey man love the vids, been watching you for a long time but there's a big problem with this video. That "negative ground wire" you said goes to the grid heater, IS NOT A GROUND! Lol I found out the hard way... I tried just grounding it to the block since it just looks like a ground and almost caught my truck on fire. It's a positive cable from the positive solenoid near the battery. Might want to add that in the description or something because it's dangerous, I was about to leave the battery charger on over night and 15 mins later positive cable melted started smoking and cooked both battery's to 0volts. If I would have gone to bed It would have caught on fire 🔥

[@Up-hill-Battle]

I think he misspoke. Because he said “power for the grid heater” as well as “ground” In sure he meant power wire.

[@kordobez3978]

@@Up-hill-Battleand I dont think heater grid will use ground to heat up, lol. Good video.. going to do mine tomorrow

[@Reyzar.]

Thank you for making these videos. I like all the camera shots and how detailed you are, this will help me with my 5.9 12v , unjust bought a custom intake horn that comes with a new plate

[@EVERYTHANGDIESEL]

Rey Rosario thanks man for watching. 5.9 cummins is even easier doing it. Just 4 bolts and your done haha. Good luck man

[@derekgillis48]

Thanks for the vidio only thing is people need to cover. Intake up if anything fall in there you will dnd up takeing top end apart again great vidio

[@enriquenerissanchez6566]

I have a 2008 6.7 with a minimax tuning, if I do that removal, will a code or a light appear on the dashboard? very good video thanks

[@goguardianfence6922]

Parts ordered, definitely a confidence booster!!

[@redpoole9323]

Well Damn good to know your a good ol NC Boy. We Neighbors. Just got my 2018 done yesterday. Didnt do the Grid delete but mabey in the Future. Hot Custom EFI live Tuning, Mechanical Gauges and Glacier Diesel Intake Horn. 5 in Turbo Back Exhaust. Trans Tunning also. I freaking love it. U got good videos bud take care.

[@BurgaBea_Stro]

nice very informative, looking to swing a 6.7 into my '06 ram mega cab and will be deleting as well thanks looking forward to seeing the rest of your vids God bless God is love

[@gustavogarza33]

Legit im gonna do this asap cause i got that battery thing happening. appreciate your tutorial. it was clean and God Bless.

[@EVERYTHANGDIESEL]

Thanks man!

[@marvinmartian3671]

Love your channel man I'm getting a 3rd gen tomorrow and I've been watching alot of your videos

[@EVERYTHANGDIESEL]

thanks man!! i appreciate the support and you will get tons of ideas from my channel, enjoy and have fun!!

[@johnmccord3395]

I’m a new subscriber and really enjoy your videos you do a great job explaining things

[@EVERYTHANGDIESEL]

Thank you I appreciate it!!

[@hookb4363]

I just deleted mine and its still running bad so im ordering the parts so I can do this because my egr bypass valve cable broke so soot literally clogged up my whole system, dpf, intake, etc. I'm hoping this will fix the problem. I'm also not mechanically inclined so this video is awsome and gives me a little ease knowing that it's not that hard to do.

[@coreyadams4646]

Excellent job, good step-by-step instructions. Im installing a 4inch monster Ram but keeping my factory grid heater. (2) Thumbs up on the video.

[@EVERYTHANGDIESEL]

Thanks man! Appreciate it monster ram intake is good too

[@EVERYTHANGDIESEL]

Changing the intake manifold wont make a crazy noticeable difference but it definitely will aid in better flow into your engine which means better combustion and potentially better throttle response and mpg.

[@jaredbrown66]

Did you need pipe dope on hardware holding the grid heater plate down or the horn? Are those bolt holes straight through requiring to be sealed asswell?

[@joselobato5429]

Hey bud, love the videos. The cable that you’re holding at 14:29 of the video is a a ground of some kind? I grounded to one of the bolts used to mount the heater plate and it smoked my hot terminal. Made me think that it wasn’t some sort of ground

[@billycook2026]

Love your videos from the start old ram diesel man WV. 1:24

[@BEASTProjects]

Great Video! I’m contemplating the grid heater delete right now. Any issues on start up on those cold mornings?

[@EVERYTHANGDIESEL]

Naw bro I've cranked her up low as 20 degrees and fires up. Grid heater is more for warming up air going into the cylinder. Get the eng warmer faster vs startup. My truck turns over fine.

[@EVERYTHANGDIESEL]

Thank you!

[@BEASTProjects]

EVERYTHANG DIESEL Thanks bro, appreciate the info. I’m going to do it.

[@EVERYTHANGDIESEL]

No worries man.

[@BladeHammer1]

Thanks for the vid. I just ordered a Grid Heater delete today! I will use this info as I attempt the replacement.

[@EVERYTHANGDIESEL]

Nice man it's easy trust me. Follow the steps in the video and you will get it done!

[@dpbjjp]

I replaced the air horn today and the checked engine light is on. The MAP sensor is plug in, the only thing that was left unplug is the plug that pug into the throttle plate. Is the throttle plate plug required to turn off the CEL? What do I need to get raid of the CEL? I have 2011 6.7 with the EGR delete. No CEL before I replaced the air horn. Great video by the way!!!Thanks for great information.

[@givmiabrke]

Great video!👍 Can’t do it to mine I see temps at 50 below ambient in northern mn🥶🥶 need block,grid,steering wheel,seat and lots of other kind of heaters here!! My grid heater was packed with soot at 38,000 miles shop vac cleaned when I upgraded to afe intake!! 😃

[@joeltaylor8814]

Thanks for the simple explanations on you videos. I bought a 2015 Cummins brand new. Only thing I have done has been a s and b intake... dont want to void my warranty. Any advice you can give one the things I can do that wont void my warranty would be great. Keep up the great work

[@ryoshi_versX]

Great video Marine. Now I know it may take a weekend to do this job.

[@EVERYTHANGDIESEL]

john kierepka thanks I appreciate it! And I wouldn't say a whole weekend. Dedicate half a day and it's possible

[@timothyharlan4734]

SEMPER FI.!!

[@illestk24civic]

What about winter cold weather? Grid heater delete will your truck start?

[@EVERYTHANGDIESEL]

Yes my truck still starts in cold weather. It until u get to minus weather will it effect it but u can always use a block heater.

[@angelmreyes89]

I did mine works real good but the only thing is the engine light keeps coming back telling me is the grid heater code p206 how do I delete the light completely from coming back

[@871jamie]

What do you do to prevent codes and a check engine light?

[@ApacheGarage]

Did you end up finding out how to prevent the codes?

[@spencerrose8238]

That wire is the positive to the grid heater, not negative, take that off before it grounds on something, thanks for the video

[@FURFEELINGS_3]

Do you have to seal up the injection lines? With anything? Also do you have to have to use rtv or gasket maker for in between the plenum and grid heater delete plate?

[@jarmmss]

Looking at doing a Banks 3.5 intake and keeping the grid heater. Just want to check and see what your thoughts are about they. Any thoughts or help are greatly appreciate Boss.

[@EVERYTHANGDIESEL]

Jim Russo banks intercooler is good! I didn't get it because you get a better deal with mishimoto and its excellent quality. I recommend getting the intake manifold too if your going that route

[@seove1]

I'm new at this. I was trying to find my heater grid on my Detroit diesel. 😂😂😂

[@EVERYTHANGDIESEL]

Under your intake manifold. Itz hard to see when everything is together just a thin little plate

[@seove1]

@@EVERYTHANGDIESEL I have a Detroit diesel. It has glow plugs.

[@jasondelapuente2592]

Can all do any delete to my cummins without a programmer to remove codes ... Will the truck still run fine ?

[@10-9USMC]

Ty sir getting ready buy what I need soon.😎👍🏽

[@seanchristophergrove790]

Best Deisel do it yourself channel on you tube.

[@mattcollins2023]

you did a great job showing and telling

[@EVERYTHANGDIESEL]

Thank you!

[@joetruitt8502]

Looks great I used a 4" banks monster air ram it sounds great it has a deep exhaust sound I didn't do the heater delete yet. I have a 2016 ram 2500 6.7L love the proformance acceleration fuel mileage and the sound of the 5-inch straight pipe. Thank you for your video of this delete because the videos help me when I do mine. Thanks again and God bless

[@EVERYTHANGDIESEL]

Joe Truitt thanks man I appreciate it! I'm glad this video helped you out! Check out my other videos they may help you out in the future and feel free to subscribe

[@EVERYTHANGDIESEL]

Joe Truitt banks makes a good kit too. I wanted it just to expensive haha. But mishimoto and pusher make good products

[@seove1]

How do you clean your engine bay? Do you have a vid on it yet?

[@EVERYTHANGDIESEL]

Not yet I'm gonna be doing a video on that

[@hardcorechampionshipjasonm5806]

Nice job brother , got the same intake horn, and would love to do the grid heater delet too, but I live I norther B.C. Canada , its - 3 and got snow yesterday, love your work, sure helped me build my 2017, 3500. Peace brother!

[@donlewis5990]

Thanks mate , I’m in Australia,so big help 👍

[@herculesinwyoming]

man i think i have fuel line PTSD after doing the banks monster ram and intake heater. which that coil heater works great 😮😮. i wasnt terrible but a fella was sore the next day .

[@sbjennings99]

Awesome informational educational video experience Y'alls

[@EVERYTHANGDIESEL]

Thanks bro!!

[@sbjennings99]

You're Welcome

[@ericanderson2149]

Post a link for the parts needed as in the beginning of the video. Great video👍

[@alldeisel2208]

Did you reuse the old gasket?

[@worrdogg]

Hey wassup bro, great video..!!! One question. About the longer bolt that came with the pusher, wasn’t that for mounting the pusher? I was thinking that it’s for the mounting hole under the double pipes. I just got mine and plan to install it soon.

[@EVERYTHANGDIESEL]

worrdogg I all the mounting bolts are the length. I dont remember a longer bolt lol it's been a min

[@rickbrown8865]

I got a question. I’ve never owned a Cummins I’ve been a power stroke guy. If I try to start my truck with out the glow plugs, it ain’t going to happen. How is this going to start on a cold day now?

[@TheEdster1981]

Thanks for posting all these videos bro 🙏

[@EVERYTHANGDIESEL]

Yessir

[@camping1947]

I do like your videos. I have 2008 cummings 3500.

[@EVERYTHANGDIESEL]

Nice I love my cummins

[@plebe817]

I delete my grid heater also I put the 3.5 intake manifold and they throw some codes p0381 p0107 p007d that’s normal?

[@Hazie345]

BANKS IS THE WAY TO GO !! Your Chanel is DOPE !

[@EVERYTHANGDIESEL]

Thanks man!

[@marnienrichaaron5813]

Thanks for posting, just got my Pusher intake and grid delete today. This video gives me a good idea of what to expect. Hope you did not have any issues with Florence blowing thru. I lived in Raleigh when Hugo blew thru in '89 and still remember what a mess it left behind.

[@EVERYTHANGDIESEL]

yeah our house was fine after the storm. grateful. those will be good installations for the cummins. will help open her up to breathe.

[@CIA_Alien]

I completed the EGR / DPF delete on my Cummins and am getting 22 mpg now. What is the benefit of deleting the grid heater? Thanks!👍

[@EVERYTHANGDIESEL]

better air flow, and not having to worry about the nut on the back of the stock grid heater falling off into your engine.

[@dennisprior2825]

Great video !! can you tell me if you torqued the high pressure fuel lines, and if so, what torque value did you use ? I've checked online and get a bunch of different values, Thanks man.

[@EVERYTHANGDIESEL]

I just made sure they were nice and tight and checked for leaks. Had no issues since then from those lines.

[@franciscohunter4422]

I have a problem with p2609 I need little help with that 🙏🏻

[@youngsemcitychris2614]

This video got me out a jam! Props to you 💯

[@That_Guy_JL]

Bro this video helped me out sooooo much today 😫😫😫 thank you bro!

[@EVERYTHANGDIESEL]

Np man!

[@skidoo31]

How do you like that intake? I'm thinking about picking one up off eBay for when I delete later this month.

[@EVERYTHANGDIESEL]

JPeters331 I love it! I bought the unpainted one for 170 on eBay. You can notice a slight difference when you open up on the pedal it's not suffocated. It's good for lower egts and better flow. I got a link in the description below where I got mine from rudys diesel

[@JJard88]

Nice work, good step by step vid. 👍👍

[@armadellos]

Thanks for the video. You mentioned that it took a bit of time to get get the truck running after the install. How many tries before it started back up?

[@EVERYTHANGDIESEL]

Turned the key and held it for 15 seconds 2 times and she fired up 2md time. Just needs time to build fuel pressure up

[@billywoodard8633]

hey bruh how can i reach out to you??

[@russellmoore6705]

Banks makes the best flowing he has a lot of time invested into it

[@EVERYTHANGDIESEL]

This is very true!

[@mater4562]

Been doing some reading and I’ve seen where tuning is required. What do you know about that and is it just so you can keep the air to fuel ratio where it should be?

[@tristen2264]

I need your help I did the grid heater delete and my truck runs but then the idle messes up in the truck dies

[@hunterlee3969]

I just did man I was throwing a code. I didn't put the MAP sensor back on. Thanks to your video you saved me a huge headache. One question though. What did you do with the prob that was in the side of the intake elbow?

[@hunterlee3969]

Thank you so much brother!! I appreciate you more than you know!@@EVERYTHANGDIESEL

[@juiceda6]

EVERYTHANG DIESEL From the day i got my truck i went and ordered literally everything you have done and love my truck. Only thing is, i left the original plug that went into the intake plenum and left it hanging, your saying i can just unplug it? I also had it tuned on the raceme tuner. Any other suggestions id like to get good gas mileage when i want and crank it up when i need. What u think my next step should be? Thanx keep up with the videos and if your ever in las Vegas done hesitate to holler.

[@Bena0616]

Hunter so what did you do with the probe? I’m kind of at that stopping point myself

[@daAUburnit]

Any details of the paint you used? Was it a high heat? What was total time of install?

[@EVERYTHANGDIESEL]

Vht engine enamel paint

[@TheKnightquest]

what about the little pick looking probe on the back side of the intake where does it go?

[@EVERYTHANGDIESEL]

Michael Eagan from the stock manifold?

[@TheKnightquest]

EVERYTHANG DIESEL yes sir. It's hooked into the backside facing the firewall. Just wondering when you put the new intake manifold on where this pick went to.

[@EVERYTHANGDIESEL]

Michael Eagan that probe looking pick on the back side of the manifold is for the old one. It has to do with some egr component. Idk what it's for. Maybe some air probe to sense inlet air temp for regens I dont have it on anymore.

[@charlesreeves3140]

Where did u get this grid heater delete kit

[@EVERYTHANGDIESEL]

Ebay

[@stariontransport7991]

So I'm just guessing...did you just remove all the ground wires..hot wires etc and the relay by the turbo and basically just discard all that..??

[@EVERYTHANGDIESEL]

Not even all that I just disconnected the negative cable on the grid heater and tucked away

[@anthonyprats8095]

Looking to do this to my truck here soon now do you still have the check engine light for the open circuit for the grid heater or does it go away with everything taken out?

[@EVERYTHANGDIESEL]

Everyone once in a while if it's really cold yes, but once I completely removed the wiring harness I dont get it no more

[@MisterIcool]

Is that the Milwaukee 3/8" ratchet I always see you using in your videos?

[@EVERYTHANGDIESEL]

yeah man i love that thing, had it for 4 years no issues!

[@kwdoss56]

Nice video! Thanks dude.

[@jet0577]

Sweet. Looks easy enough

[@EVERYTHANGDIESEL]

It is man very straight forward

[@detectionhobby1113]

Hello. I bought my first diesel and comes with intake air heater deleted and still throwing a p2607 and a lot of other codes like p0299 and I dont know how to fix it. Any ideas??

[@zack2008100]

Did you have any issues with the fuel lines leaking? I'm having hell with mine. My pickup is a 2018 3500

[@EVERYTHANGDIESEL]

no i didn't u may need to clean the threads also tighten them good when installed

[@robertthibodeaux4435]

Thx for sharing! Did you have to relieve the fuel pressure somehow before you started taking off the injector lines?

[@EVERYTHANGDIESEL]

Robert Thibodeaux no worries man and no I didn't I just cracked the line. There is no pressure if the pumps aren't working and it doesn't hold prime pressure when off. You will be good.

[@robertthibodeaux4435]

Thank you for the reply sir and keep them good videos coming!! I appreciate your efforts!! Thanks to you and your videos I am soon ordering air dog and sump, pusher intake with h grid delete,Mishimoto intercooler and glowshift fuel pressure gauge on my 2007.5 6.7 Cummins that I bought new in 07! I’ve been Deleted and voided my warranty since 16000 miles and have almost 60000 now! My upgrades are Banks Cold Air intake,Smarty Jr,(running 60 hp tune constantly)Mishimoto Radiator,Deep trans aluminum pan,Mag Hi Tech rear diff cover,Pillar pod gauges with Trans Temp,Boost And EGT’s!! I have gotten as much as over 25 mpg on my 2500 quad cab 2 wd!!! Love my Cummins!!!! THX!!! Also 4” exhaust pipe with spincast muffler,5”tip!

[@EVERYTHANGDIESEL]

Robert Thibodeaux NICE stuff man! Haha I like the list of to do mods you will be happy when you do the loft pump and intercooler. Also you got some good stuff done already to your truck! Are you running stock tires getting that mileage?

[@robertthibodeaux4435]

Yes running stock size tires!

[@m9b7v5]

What about heater wiring?

[@EVERYTHANGDIESEL]

Just remove it.

[@drummerguy676]

Good job bro I’ll be doin this to my welding rig

[@EVERYTHANGDIESEL]

Yeah man its worth it! She can breathe normal now lol

[@jturquette]

I have watched this video 3 times and will watch it again a few more times in the coming month as I prepare to delete my grid heater and switch to the throttle valve grid heater from glacier. quick question: when you re-installed the fuel lines from the common rail to the injectors, how tight did you go? I imagine there was no torque wrench used. just curious, would have to strip something or "F" something up. Thank you for showing this.

[@EVERYTHANGDIESEL]

no worries man. when i tightened the lines i just used a regular wrench and got them tight. probably like 1/4 in turn past the sharp rise of torque. you'll know when there tight haha

[@jturquette]

EVERYTHANG DIESEL well, I got the grid heater delete done last night. It took me about 3.5 hours. I did not even try to remove the #6 injector! Ha ha. No diesel leaks (yet). That was my biggest concern. I will check it again in a few weeks. What I did was buy the Glacier diesel Grid heater relocation (goes where the air inlet valve used to be). That way, no cold starts for me. Quick spin around the block last night and it feels a lot mor responsive! Thanks for the video. It helped me overcome my fear about doing this.

[@EVERYTHANGDIESEL]

Congrats man! Glad I could help. This is the only video on KZbin showing how to do a in depth step by step grid heater delete.

[@kodagaming9437]

Did it throw any engine code after you did that?

[@EVERYTHANGDIESEL]

No sir

[@jet0577]

What was on top of the old intake and what happens to it when you replaced it with the intake elbow?? It also had a brass bar that went across the manifold in the front. Was it completely removed or rerouted?

[@EVERYTHANGDIESEL]

Are you talking about the blue plate? Also for brass bar not sure what your talking about?

[@freddiesantander7510]

I'm new to the channel and late to the game. I bought a ram intake and boost tube upgrade. My question is do I still need to do a throttle body delete? I also cause of your channel bought my heater grid delete also. Could you help me

[@EVERYTHANGDIESEL]

If your installing a aftermarket intake horn u don't need a throttle delete.

[@freddiesantander7510]

@@EVERYTHANGDIESEL Thanks I appreciate it

[@paulisadora]

What are you standing on to reach into the engine bay?

[@EVERYTHANGDIESEL]

a cooler lmao

[@noahbeijer3107]

That cable the goes to the grid heater is not ground, it’s actually a live wire when the car turns on the grid heater relay, the grid heater gets its ground from being mounted to the engine. It also isn’t fused so definitely disconnect that or take it out.

[@EVERYTHANGDIESEL]

Already took it out.

[@noahbeijer3107]

@@EVERYTHANGDIESEL awesome man! Thanks for the video too! Gonna do my delete sometime soon’

[@nealhess6770]

Amazing video....thank you 😎

[@EVERYTHANGDIESEL]

No problem man! Thank u!

[@TheRealBrandonMartin]

How much of a difference did this make? And what did you notice the most?

[@EVERYTHANGDIESEL]

Not really a hp mod, but it does make a difference

[@davesshop4519]

With a Bone Stock 2016 Ram, Can you do all the deletes on the Right side of the motor[Heater, Race Plug, Air Ram, EGR] and not anything thing else? Would that work with a Stock OEM Tune and Exhaust pipes? or What deletes would be recommended on a stock tuned truck in conjunction with the Heater delete only?

[@EVERYTHANGDIESEL]

if your emissions are removed you can do all of these mods with no issues. if your emissions are intact you cannot remove your egr or dpf without tuning it will cause a check engine light and your truck will go into a limp mode.

[@austenazevedo6078]

Can you remote start the truck without the grid heater? Does this not throw an engine code?

[@EVERYTHANGDIESEL]

Not sure I dont have remote start. I would assume no but not 100%

[@rawcummins1665]

Where did you get the grid heater delete plate from?

[@EVERYTHANGDIESEL]

Ebay

[@rawcummins1665]

@@EVERYTHANGDIESEL any one? Witch you recommend?

[@EVERYTHANGDIESEL]

I got the 2nd to cheapest one lol

[@badkarma2369]

Does it sound any different without it??? Driving??

[@northwestcustoms6663]

Just curious why delete the grid heater? Do you live in warm climate all year?

[@EVERYTHANGDIESEL]

Where I live it doesnt get cold enough to require a grid heater, in winter cold here is like 40 degrees. Grid heater puts a strain on your alternator and you have the potential of that nut on the bottom side of it coming off and going into your engine.

[@northwestcustoms6663]

@@EVERYTHANGDIESEL ahh. That's what I kind of thought. We get -40f and colder here sometimes so it is needed.

[@daniellujan3302]

If I do this grid heater delete. I’m gonna have trouble starting it in colder weather? Is their a solution to it like a add on to the intake and acts like a heater?

[@EVERYTHANGDIESEL]

Yes gdp makes a gird heater relocation for the intake manifold

[@EVERYTHANGDIESEL]

You won't have trouble starting the truck unless its below like 10 degrees

[@RobRocker09]

Banks 3 1/2 is better look at the engine and your new intake. one is round and the engine is rectangle. Banks is rectangle, the injectors not a straight shoot and the injectors ports are not mixing right. Where the meet at the lower end of the elbows. only one tube is getting the injected mixture, Otherwise great video.

[@paramedicbenmedic7276]

So my question is if you delete the grid heater what makes the glow plugs heat up

[@anthonyvaughan8002]

Cummins is too superior for glow plugs..

[@EVERYTHANGDIESEL]

Cummins don't have glow plugs

[@brockbauer4919]

Great video man! But why did you decide to delete the grid heater?

[@EVERYTHANGDIESEL]

Brock Bauer better flow it's very restrictive. Plus I don't really need. I dont live where it gets really cold. If I was up north then yeah I would keep it. But I seen cummins start up in the teens with no grid heater. Sorry for the late reply I didn't even know you commented until I randomly came to the video. Thanks for watching

[@Badboyzz-zw7iy]

Everythang_Diesel, love your channel! I recently bought my 2014 Ram 2500 Crew Cab truck. I'm a new Diesel owner and I have a question. 3 Weeks into my Cummin's and a get a check engine light. I took it to the dealership and they tell me the Turbo Actuator is going out and needs to be replaced. This one is on them and I don't need to pay but with the limited warranty, the next one is on me. Can I do a CCV Delete like you showed on your CCV Delete video and not get a check engine light? I don't have a tuner yet and haven't put any deletes as of yet.

[@EVERYTHANGDIESEL]

Thanks for watching man. Yes u can do a ccv delete but it will void your warranty. That would definitely extend your turbo life! A 2014 ram having a bad turbo in 4 yrs is kinda short? Sucks that happened. Make sure you running some clean preferably synthetic oil. Good luck man! Congrats on the cummins

[@1984hydro]

Yes you will get check engine light, i tried , i have since had a delete amd tune , havnt tried again but the shop said it should be turned off amd i could deltet the ccv now

[@seanyboysean]

Thanks to you, I fired my cummins mechanic 👍 #ImTheMechanicNow 🦾

[@MMAfighter32732]

How do you like the intake ypu put on?

[@EVERYTHANGDIESEL]

It was good man!