Everything you need to install a new fork for Razor MX500 & MX650

Comment any questions and I’ll try to answer everyone. Here are all the parts mentioned:
29" Front Forks
www.amazon.com/dp/B0C98LXNB2?...
PGN (2 Pack) Bearings
www.amazon.com/dp/B07BTG15BM?...
12mm / 220mm Axle
www.amazon.com/dp/B0BRN6PHHW?...
Suspension Grease
www.amazon.com/dp/B09FTJXZK1?...

[@memesquad9608]

God bless you. Most people in this community would claim the have "custom forks" and try to resell them for $350 or something.

[@lukeb4687]

very helpful video thanks!

[@TuckerBlack]

Thanks man this helped a lot with finding parts

[@kelteckiller]

What front brake and caliper kit did you go with for the front fork? Is it hydraulic and did you order it from Amazon?

[@vojtechcisar1867]

Im looking to build something like this and i'm probably gonna build my front of off your build. Which brake calibers did you end up using?

[@godfreybrown633]

What was the specifications on the bearings

[@briancgd8498]

Awesome video dude! And the Lowe's parts list is clutch! I bought the same fork set and would've been screwed without this. Longer axle is coming tomorrow. What front brake do you plan on going with? I'm gonna share this in the Modified Razor groups on FB. Lots of people have been asking how to do this properly.

[@mikebikehikeofficial]

Glad this helped! I haven’t gotten around to the break situation yet to be honest. Thanks for sharing btw🙏

[@anthonymoy4471]

You should have a bushing thru the head tube that takes up the distance between top and bottom bearing or it wont feel as it should good work tho

[@aadricallan8651]

Do you know the best way to get that and what the size is?

[@anthonymoy4471]

@aadricallan8651 put the bottom bearing in and the top bearing and stick something in the hole to touch the other bearing lip and mark the piece you stuck in hole where the top bearing starts and measure and go to hard ware store and get a bushing to go on the inside to take up the distance it will feel so solid then run your bolt through it all and tighten down. May have to trim the bushing down accordingly

[@aadricallan8651]

@@anthonymoy4471 thank you!!

[@emilio7605]

What size forks for mx350?

[@Vmaxfodder]

How long is your neck tube ? Can I ask

[@engineeringiscool1951]

Please do mx350

[@jennifersanmartin2021]

I’m new to this how did you get the forks through the black triple tree

[@jennifersanmartin2021]

Nevermind I had the clamps on wrong great video bro.🎉

[@Vmaxfodder]

Why did you get rid of the stem?? I used Harley-Davidson berings cups conversions . It needed a 50.2mm -43.8 mm shim. But seems a lot stronger?

[@mikebikehikeofficial]

When I did my research it was the method that seemed easiest but if you found a better way than absolutely go for it!

[@Vmaxfodder]

@mikebikehikeofficial I don't know, but in my situation I need something that will take 12kw abuse but eventually 🤔 28kw of pull power . My set up is a total of 56kw . 56,000 watts, but 40kw for now. I'm using 13 in scooter tires 6ply . The smaller tires might take a little more abuse?. It is 2 fardriver 84530s. The power snapped the other fork. Actually it exploded. So I'm hoping for a lot stronger? 😕 any Ideas helpful.

[@matthewlizardi1148]

Hey so I have the same set up as you but stock bearing. I can not get the bolt to fit through the headset. There is a tube inbetween top bearing and bottom bearing that is slightly skinnier than the bearings themself. I can’t seem to figure out how to remove the bearings to get the tube out. Did u have this same tube in your headset? How did you remove your bearings? Any suggestions?

[@mikebikehikeofficial]

I used a flat head screw driver and hammer to tap out the bearings on the headset. Hope that helps!

[@eunipla]

hey i got those same forks but they're super stiff have u figured out how to soften them?

[@mikebikehikeofficial]

I haven’t, sorry.

[@nicholasharutunian707]

When you push down and pull up is there a clicking noise?

[@mikebikehikeofficial]

Yeah a bit

[@DioniTorres-sn5me]

Will these front forks fit on a razor 350??

[@mikebikehikeofficial]

They'd be too big I think

[@cameronrogers7577]

That stem is not 10” 1/2 it has to be longer mine does not even come close to clearing the frame

[@mikebikehikeofficial]

@@cameronrogers7577 🤷‍♂️

[@Ksu_ju]

Do you think this will fit on a hawk 250

[@mikebikehikeofficial]

I think it’d be too small

[@dogdronesearchdd3782]

Will this work on a razor sx500?

[@mikebikehikeofficial]

Yeah I think it’d work

[@claudiohernadez1928]

How did you take those bearings off?

[@mikebikehikeofficial]

Flat head screw driver and mallet

[@claudiohernadez1928]

So I got some new shocks from ride or die and I was looking at some new rims. Can I put any type of rim on them as long as it’s a 12mm hub hole ??

[@claudiohernadez1928]

Forks my bad

[@michaelg8191]

nice vid. direct links to the parts list from lows photo would be appreciated by anyone watching the video

[@junkybuilt8990]

Not hard to copy and paste into Lowe’s search bar

[@ThatGuysGarage1]

What rear shock did u go with?

[@Rippinandfishin]

240mm

[@mikebikehikeofficial]

I have a video with all that info

[@Max-tc6tq]

How much mm is the rear shock

[@Rippinandfishin]

240