F150 Crank No Start Diagnosis

F150 Crank No Start Diagnosis
Link to my Amazon Affiliate Shop:
Amazon Shop - www.amazon.com/shop/aaronrose

[@marioalbertog.8305]

15:47 ... "oh dude shut up" Jajaja.

[@r8r4life36]

You gonna get on here tell old dude shut up.. gonna watch his video trying to help people.. learn some Respect ..

[@scottcecil8106]

Thank you very much, you helped me determine the same issue, my brother's truck was sitting for 2 years, trying to get it running, watched your video, and was easily able to find the problem, bad fuel pump. Thanks again.

[@che2335]

Check the fuel pump inertia switch behind pass side kick panel press the red button down.

[@shawnnance3670]

Video of a crank no start on a truck that cranked and started

[@eddyrodriguez6909]

Did you watch more than 2 min?

[@r8r4life36]

Thanks for all the tips it could be !! Mine did same thing

[@rorybellamy2533]

i had symptoms like this on E 150 van , after a fuel filter and pump , it was more in the IAC.

[@dexterbell7017]

Super helpful video my 01 f150 was having the same problem that I couldn't figure out until watching thus

[@fokuz02]

My 01 Super Crew has been a strong workhorse with 207k and counting. That thing is dead nuts solid!

[@billywalker8375]

fokuz02 257 k on my 01 super crew other than normal maintenance I have put on a alternator and a egr

[@Maniaco.Dee.23]

😂😂😂 i got 435k+ extended cab and she just went out in me

[@texxs01]

Diagnosis doesn't stop at "fuel pump doesn't work" the question is why it doesn't work. You didn't check for a clogged fuel filter for instance. There's also a unique problem with this generation F150's , a wiring harness on passenger side of engine rests on a hot pipe - it's insulated but still hot melts the insulation off the wires and then the power from somewhere doesn't get to someone where and if you fix or replace those wires, it works again.

[@17HOM]

Acabo de reconstruir el cableado que se quemó con el escape, pero sigue sin encender solo da marcha y como. Alos 3 intentos de marcha se sigue descargando, tienes algún diagrama de cableado?

[@texxs01]

just like my 2002 F150, that damn chiming makes itr hard to hear. Why does it even need to chime (even with the door closed and seat belt on) when I start it?

[@Vidmr2407]

Great video! My 02 5.4L is doing the same thing and all fuses/relays are ok. One odd thing I wanted to ask about is I was assuming it was the fuel pump and no pressure at rail, then all of a sudden after checking every day for a week one day it started and ran fine up to full engine temp. When I turned it off and immediately tried to re-start, got the crank, NO start again. Just seems like a weird way for the pump to be intermittent. Any ideas guys? - update: yeah it was the pump of course :)

[@aaronsrose]

The truck from this video was intermittent as well. I would try to swap out the fuel pump relay for a known good to see if that could be the issue. If there is not change, I'd go for the fuel pump. Thanks!

[@hearsejr]

You dont have to suck the gas out. Open the fuel door remove the screws holding the fuel neck to the bed, remove the bolts the hold the fuel tank side of the bed on the frame, losen the other side of the bed bolts thst hold the bed to the frame but don't remove them completely. Get a friend to stick a 2X4 to prop the bed up and then you can the fuel pump out. While the fuel pump is outplace clean towel over the fuel pump hole in the tank. It tskes sbout 30 minutes with an electric impact gun.

[@leroysmith2821]

Not a rusty one in northeast,bed rails would disintegrate.. removing bolts.

[@locknload9143]

I have a 06 F150 5.4L . Has spark, hear fuel pump come on, checked all fuses and relays. "Crank No Start". I have no Schrader valve, so I used Quick Start. Check 4 of 8 coils all have spark. Battery alternator starter all seem to be fine. Think I bought a truck with a Gremlin. Any suggestions? Oh yeah, battery died so no codes! Had previously camshaft positioning sensor codes. Changed both out.

[@aaronsrose]

I think these trucks started using a fuel pump control module in about 04. It's usually under the floor on the frame around the front of the spare tire. I think it controls the speed of the pump. If that is crapping out maybe it's not allowing the pressure to get to where it needs to. I'd see if I could find and test the fpcm.

[@Vidmr2407]

Great video! My 02 5.4L is doing the same thing and all fuses/relays are ok. One odd thing I wanted to ask about is I was assuming it was the fuel pump and no pressure at rail, then all of a sudden after checking every day for a week one day it started and ran fine up to full engine temp. When I turned it off and immediately tried to re-start, got the crank bo start agsin. Just seems like a weird way for the pump to be intermittent. Any ideas guys?

[@dawildcatz87]

My 02 is doing the exact same thing right now. When it does start she will run for hours like a top but if I shut it off and come back there's a high chance it just cranks and never fires. Did you figure yours out?

[@Vidmr2407]

@@dawildcatz87 yup, was intermittent fuel pump operation. I got one cyber Monday from NAPA for like $120 and paid a local guy $160 to drop tank and install. No more problem. Hope it’s an easy fix for you. Happy new year!

[@lillianasanchez5028]

@@dawildcatz87 same exact problem here g

[@dawildcatz87]

@@lillianasanchez5028 fuel pump replacement fixed my truck. Eventually it got so weak it wouldn't prime at all

[@dwatson4]

2001 XLT sport no power to fuel pump. When testing voltage at relay socket in key off there is 12v on one side, key on 12v 2 sides and 7.7v on the fuel pump side. How’s that happen?

[@aaronsrose]

If the 7.7V is through the relay, I'd swap it with another to see if it changes. If it works better with another relay, I'd put a new relay in it and continue. If the 7.7V (should be 12v I'd expect) at the relay socket is not making it to the hot side of the pump, I'd start running down the wires from the relay to the pump to see if there is a broken one or short somewhere. And for grins, I'd make sure the fuse is happy as well.

[@alphaadrenaline7537]

I can hear my fuel pump and it has all new plugs and coil and cranks string but won’t start, has died once in me before but started right back up and lasted another hour before I was home with no issue and now it won’t even start at all

[@aaronsrose]

Still could be fuel pump failing. This 03 would sometimes start and run a little and then die when the pump stopped producing pressure. A fuel pressure test would confirm that.

[@jakemason9436]

Part two.....

[@dawncoates3667]

My 1997 ford expedition 5.4 liter at first will start for a second then die, then no start, but will crank no problem.

[@aaronsrose]

That's exactly what this truck would do. The pump would work a little when it was cool but it would then heat up and stop. If there is no fuel pressure with the key on, I'd look at the pump and filter. Thanks!

[@405544]

Have similar problem on 03, 4.6L except the fuel pressure goes to 40 psi with ignition on, then drops immediately to zero. I am also getting no fire, or rpm reading. I am wondering if the ecm is sensing zero fuel pressure and shutting off the ignition to spark. It seems there may be a bad check valve in the fuel pump, even though it was change not long ago. Any idea why there would be no spark following what appears to be fuel bleed off after initial ign on?....thanks

[@r.c.1314]

Check your Crank Position Sensor

[@rodneybrand8521]

Check fuel driver module..could be a corroded connection..it's mounted by the spare tire..

[@aaronsrose]

Excellent thought. Will do. Thanks!

[@samdorsey4590]

Isn't one on the 2003. Started in 2004

[@WallyJ2K]

But wouldn't a faulty Fuel Driver Module throw a code? I have a Crank but No Start situation but I'm getting a "Pass" with no codes fired.

[@aaronsrose]

Howdy! The FDM failure may throw a separate code, but they didn't start being used until 2004 in the second generation of the triton engines. The black F150 in this video threw Lean Bank codes when it's pump failed. But my 97 never coded at all when its pump died last month even though it ran really badly for a fair bit of time. Best check for the pump is the schrader valve on the fuel rail. If it's not spraying everywhere when the key is on, the pump is seriously suspect. Thanks!

[@WallyJ2K]

@@aaronsrose How do I know it it's the FDM vs the Fuel Pump? Also, I tried the test where you spray starter fluid to check for missing fuel, and the engine still didn't fire up at all, not even for a couple of seconds, which makes me think it's a spark issue. I can't find my Shrader valve to check for pressure. Found one valve that spewed green liquid. That wasn't it.

[@raymondmiller3057]

my f150 is dead the battery is charged but wont do anything. you can jump it off and it will crank,but when you remove jumper cables it dies.

[@aaronsrose]

That's different. I'd start by confirming that the battery is good and then check to make sure the alternator is charging. Thanks!

[@dannypalmer7701]

It petered out!

[@bigbear4133]

Was it a bad pump??? Mines doing the exact same thing

[@rogeliodominguez4298]

Did you figure it out if it was the pump ?

[@johngates8892]

1996 f 150 in online 6cylstarts but no power whenever accelerations engine runs really rough hascomplete. New. Tune up and. Distributor.

[@richardtaylor9367]

What about the fuel module?

[@aaronsrose]

The fpcm only started in the f150 in 2004 with the 3v. Thanks!

[@elicaraballo8990]

I have a 2004 Ford F150 5.4 L heritage edition.. At times, it won’t crank over. The only method to successfully turning it on, is to disconnect the inertia, turn it on and then reconnect the inertia switch. When it doesn’t turn on, the inertia switch is not tripped. I have since replaced the switch with a brand new one, but the problem persists. If anyone has any idea as to what I should do, I would really be appreciative! Thank you.

[@aaronsrose]

That is weird. Have you tried to bypass the inertia switch completely by wiring around it? It could be intermittent contacts in the connector to the switch.

[@elicaraballo8990]

@@aaronsrose hm not quite sure how I would do that.. I was going to try to splice in a toggle switch but not certain which of the two lines to tap into??

[@kevinswindell8062]

Fuel filter

[@Thatbluef150]

Pretty sure mine is my fuel pump mine started at first but than it died than It cranked and wouldn’t stsrt

[@aaronsrose]

Yep. That is a very common symptom.

[@beemerkon]

If that was your test to determine the fuel pump you better go back to school

[@it3897]

This helped me a bunch with my 2002 f150

[@kalegarfield2346]

Fual pump relay switch 😂

[@anthonyrosanelli.]

Was the fuel pump the problem?

[@aaronsrose]

Yes. My next video showed changing it and its been running well since. Thanks!

[@samdorsey4590]

@@aaronsrose nice fix Aaron!! My 2003 F-150 4.2 L V-6 will crank but will NOT start or even act like starting like your 2003 4.6 L V-6. It ran fine when I parked it the nite before. I'm NOT getting any spark & CANNOT hear the fuel pump running with the key on! Any ideas would be greatly appreciated!! I did replace the coil pack but no luck!! All the fuses are good! I checked them first! Maybe PCM relay or the PCM itself? Any help Aaron would be greatly appreciated. I did some research here online & found out there is NO Fuel pump driver module on the 2003. Ford started putting them on in 2004. I even crawled under the rear, with the spare tire removed & only thing there is a canister. I have MS & NOT able to do as much as I use to! I'll be waiting to hear back from you! Thanks!

[@aaronsrose]

Sorry to hear that. If you have no pressure st the fitting on the fuel rail, the pump is either not running or has failed. Unless it's always been loud enough to hear the pump. You may not be able to. If the fuses and relays are good and the truck cranks over with the key it could be the pump and/or filter. If you've checked for spark by pulling a coil and plug and cranking the truck while grounding the plug on the head and saw no spark, especially on multiple coils, that's a different problem. I'm not sure what controls the firing of the plugs but I would check to see if the ECM is getting power correctly. Good luck.

[@samdorsey4590]

@@aaronsrose thanks Aaron! I'll get those things checked out.

[@samdorsey4590]

@@aaronsrose just a update Aaron. So I went out today to see if I had spark with the new coil pack I put on yesterday! I do! I got zapped! Lol anyway I put the plug wire on & it started right up!😳 I let it run for 30 minutes. It never stalled out!! It idled smooth except a time ot two it slow down then back up!! I'm thinking fuel pump as per your video! But I'm gonna just cut a hole in the bed! My truck is rusty some what the heck! Lol

[@sogent56]

Get to the pump by sliding the bed back.

[@jeremiahn3014]

Dude your funny 🤣🤣🤣🤣

[@user-bx5rx8lk1s]

Check crank senor

[@Sawmill3872]

02??? CHECK BATTERY IN KEY.

[@samyza2005]

my truck ran out of gas I put gas that was in my g can now wont start

[@aaronsrose]

Definitely check for fuel pressure at the rail. Could be the pump. Good luck.

[@longdongsilvers1784]

Same bro it was sitting with no gas for almost a year. I recently replaced the fuel pump fuel filter and nothing I can hear the pump come on but I’ll try what he did

[@waynes8226]

Ignition switch $25

[@samsonkabelomolekoa2871]

I want to no why nissan fuel pump not working

[@aaronsrose]

Could be age. Depending on how old it is these parts certainly can wear out.

[@johngates8892]

1996 Ford. F

[@truth409]

Mine is 2001 Lots of water on the passenger side in the carpet it cranks but won't start

[@SanchoGracie]

The famous windshield leak. Disconnect your PCM & inspect the harness on the firewall & the unit for corrosion/water damage.

[@user-ij5gi6be8g]

This wont start at all replaced crank sencer still wont start

[@aaronsrose]

Does it have fuel pressure?

[@josiemarroquin2736]

Cranks don't start

[@kalegarfield2346]

Check crank relay fual pump relay switch them out it will start

[@truth409]

2001 no start...no codes....water in carpet passenger side???

[@aaronsrose]

No start if it cranks certainly could be the fuel pump. The water might be either the AC evaporator drain is plugged, of the heater core is leaking.

[@truth409]

@@aaronsrose It's got water on both sides even the rear view mirrors got water From it's been raining a lot lately now it's running again for some reason

[@SanchoGracie]

Need your windshield resealed. Pull the PCM. Inspect the unit & harness for water damage/corrosion. PCM maybe toast.

[@bigwo56]

Easier to lift the bed than to drop a fuel tank with 12 gallons of fuel! Just sayin..

[@davidlambert7937]

I cut the bed

[@elcepe1609]

Inyectors

[@potatosalad5355]

There is not fuel pressure on the fuel rail... and then the engine sometime start... so...go back to School

[@beemerkon]

Absolutely wasted my time with this video

[@Mr77boxChevy]

Check your crankshaft sensor

[@coopergt500twin5]

It’s not the problem I have the same exact truck lol change bank 1and bank 2 cranks and starts when truck is cold she drives beautiful but when I turn off truck won’t start back up fuel pump could be the problem and yess just changed both sensors because auto-zone said to haha played me ain’t the problem but they were dirty tho