F30 used EPS programming ... No Current Coding Data Stored

[@dragos002]

Same procedure is in case to change a tms module ?

[@heshamessam8042]

Yes ... if same fault .. also may need to do on frm itself ... also may need to initialize with ista

[@dragos002]

@@heshamessam8042 i have a coding error on diagnose.

[@heshamessam8042]

@@dragos002 ok ... cafd missing... go firstly with esys

[@dragos002]

@@heshamessam8042 thank You sir i will try

[@JaysonFlores-d1p]

is changing istep needed? If so how do you determine it needs to be changed since I just see you change it but nothing to explain it though.

[@heshamessam8042]

@@JaysonFlores-d1p you can do if you want ... not necessary

[@JaysonFlores-d1p]

@@heshamessam8042 Thank you Teacher for the answer. I just flashed and egs and now i can shift. ISTA is asking me to encode it. Just follow what you did to code it? Right click on egs and code?

[@heshamessam8042]

@JaysonFlores-d1p yes ... or perform on tal

[@JaysonFlores-d1p]

@@heshamessam8042so it means that i need to remove patch files , replace originals and update egs to latest version

[@thorsoldier666]

One more question??? Can that coding be done with the engine runing?

[@heshamessam8042]

Yes ...

[@thorsoldier666]

@@heshamessam8042 thank you!!! Your video helped me a lot!!! Now i cant start programming the EPS

[@heshamessam8042]

Thanks

[@thorsoldier666]

When im doing the calculation for the TAL file appear a message telling me 3 TAL LINES HAVE BEEN SENT TO STATUS "NOT EXECUTABLES" DURING TAL CALCULATION...[C384]

[@heshamessam8042]

@@thorsoldier666 and then can't continue performing tal?

[@terencedegree9079]

How did u get ya battery volts to show mine wont can you please send me your link

[@heshamessam8042]

Tell me a second too see battery voltage

[@AntonioArsuta]

Hi Hesham, can I use this method for flashing other ecu's? kombi bdc etc etc? thank you for the videos

[@heshamessam8042]

Yes thanks

[@AntonioArsuta]

@@heshamessam8042 sorry I wanted to understand if it is also good for the Mini F series

[@heshamessam8042]

@@AntonioArsuta yes

[@AntonioArsuta]

@@heshamessam8042 hi, sorry for asking for more information. I flashed the ecu but not all, then today I went back to connect to flash the rest of the ecu but it doesn't allow me to do full flash anymore, it gives me not available on i-step Target and shipping, what's wrong?

[@heshamessam8042]

@@AntonioArsuta make sure to choose correct istep shipment ... also newer data (target) ... or maybe wrong fa or wrong isteps written on fem

[@Samafolife]

Hi brother, I would like to update the DME module in my BMW, should I use ISTA or is safer to do the update with ESYS? Thank you

[@heshamessam8042]

I prefer esys

[@Samafolife]

@@heshamessam8042 okay. Thanks👍

[@thorsoldier666]

Ok after thinking and looking in the codes i found what i need and i programmed succesfully thank you sir !!!! Thanks to your video now i have coded EPS🎉🎉🎉🎉🎉

[@heshamessam8042]

😃😃😃

[@joker8541]

Hello I flashing ecu with esys new have overboost🙈

[@heshamessam8042]

What do you mean by overboost? I don't understand clearly

[@joker8541]

@hesham essam sorry for my English not very good 😊 my turbocharger start working no no good.have overboost .After flashing ecu.i flashing because have stage 1.i trying return original software

[@heshamessam8042]

@@joker8541 never mind me too ... i think now all ok ... because esys use original stock files

[@joker8541]

@hesham essam but now after the update ecu the turbine is not working properly

[@joker8541]

@@heshamessam8042 before that everything was fine until it was stage 1

[@asefali5926]

Hi, I have F20 BMW 1 Series 2018, when I check ISTA it shows there is no communication with EPS, do you have any idea what the problem could be?

[@heshamessam8042]

Check.power ground ... maybe eps.itself

[@WuJacket]

Hi hesham, very good video, do you know how to flash a HU module,with Esys, I got a constantly rebooting issue.

[@heshamessam8042]

Hello ... thanks ... will be same way as i think

[@zumiezskater122997]

are you using ICOM or just Enet

[@heshamessam8042]

Icom

[@zumiezskater122997]

@@heshamessam8042 original?

[@heshamessam8042]

@@zumiezskater122997 orange one ... icom a2 ... chinese as i think

[@zumiezskater122997]

@@heshamessam8042 orange one works with G series cars ?

[@heshamessam8042]

@@zumiezskater122997 yes

[@林鋒碩-e4j]

你好棒，我喜歡

[@heshamessam8042]

Thanks

[@mrplay145]

Thanks!