Use this link to buy anything on Amazon and it will contribute to the channel costs you NOTHING! amzn.to/2R0LGvD
Пікірлер: 46
@jameshatton4211 Жыл бұрын
Thank you so much for a fast speed time lapse. That's exactly what I needed! I have worked on so many cars in my time and this is the first one that I needed to look up how to pull it apart? Because it's a German car I was not aware how much stuff they have for the cooling system and how many attachments they have for plastics parts to make the car lighter but not vibrate to pieces? Smart engineering but frustrating to know that there is always a bolt or screw that hasn't been undone because it's somewhere you can't friggin see? So much work before even getting to the part that is the issue? I was given the car for $100 so I just have to keep reminding myself that the cheap price will be worth the frustration for a good car in the end? 🤞
@jeffmillsap81093 жыл бұрын
I need mine replaced. VW wants an arm and leg for it done. Where you located??
@henryrodier80243 жыл бұрын
Once you’ve done this 6 or 7 times lol this must make you an expert mine doesn’t have enough miles on it yet I guess a newby with 169,000 miles 2011 TDI
@Mikefngarage3 жыл бұрын
my dmf went out at 240k miles. but that was lots of highway... it will start rattling pretty soon listen for it when you turn the engine off it starts there with a little extra couple of light noises. then it starts doing it while idling. Also listen for the clicking when you put it in gear from reverse to 1st. or opposite. that will be the first signs of clutch wear. If I could turn back the hands of time I would have done the clutches at the same time. not hard to do while the trans is out. Keep up on those trans oil changes too.
@nicolastremblay75272 жыл бұрын
Mine went out at 150k miles. I like to slap the car a little bit and my girlfriends do a lot of Uber delivery with it, so I think we kinda killed it early. lol You might be near !
@hardcore44762 жыл бұрын
Mine started rattling at around 210,000 still driving it but need to replace soon and why I’m here..
@BrokenPilot-n7bАй бұрын
I have been experiencing a problem with the DQ250 gearbox for the last 10,000 km and it sounds like this: When the clutch engages there is a clunk, the gear shifts are very linear and nothing is felt, except a clunk and a little jerk. I have noticed this phenomenon also when I go, in any gear, take my foot off the accelerator and put it back on, a clank is heard. I'll leave some videos below with what I'm trying to explain. I'm guessing it would be the dual mass flywheel, the car having 210k km. The dog bone and mounts are ok. Replaced the CV Joints but nothing changed. The sounds appears when you try to reproduce the noise which gets louder and louder the more you try to reproduce it Also when i'm in idle i feel sometimes some vibratians and when i put it in D, the vibration dissaperes. On VCDS there's no errors from mechatronic unit. What do you guys think?
@mikecbrkdrvr88992 жыл бұрын
My 2013 JSW TDI needs a new dual mass flywheel soon and I'm still having nightmares about the on my daughters 2009 JSW about 5 years ago. I had watched some of Mike's older videos and this new one looks even better. I do have a couple of questions/comments. The 1st being can anyone recommend a decent and/or reasonably priced transmission jack to use while the car is on jack stands? I bought a cheap Harbor Freight model and had to combine with hanging trans with fender to fender cross brace to get trans back in myself and it still took me hours. 2nd I watched a bunch of other KZbin's and saw one other guy remove the (flanges?) that the axel attaches to at the transmission before he removed the trans, he claimed it made it easier, I am wondering about this and if is safe to do? does it require new torque to yield bolts. I seem to remember those flanges being part of the "hang up " in getting trans out ( I actually chipped plastic fitting where the electrical harness plugged into the trans).
@danielhowardDaniel123gamer3 жыл бұрын
So you need to recalibrate the gearbox after replacing the dmf?
@bpl08072 жыл бұрын
There is no recalibration necessary for a DMF replacement.
@untimelyconversations3329 Жыл бұрын
How do you change the transmission oil. I've been told you need a special pump for that job
@ShotGunner5609 Жыл бұрын
I just drains out the bottom, technically you have to refill it from the drain plug using a specific adaptor/pump. But i just re sealed everything and refilled from the filter port hole on top under the battery. Just takes alot longer but doable.
@patthebaker16402 жыл бұрын
So how feasible would this be to do without a lift? Would I be able to get the transmission off with just a jack and some cribbing?
@Mikefngarage2 жыл бұрын
did one by myself on the ground the first time. Was a little hard but not too bad.
@hardcore44762 жыл бұрын
Hey Mike what size extension did you use for driver side axle? 3/8”?
@javierm22037 ай бұрын
what are the sockets you were suggesting buying from amazon? I know the DMF has the same socket types needed
@marvin41ful Жыл бұрын
Can't you take that flange (for axle) off and reinstall when the transmission is back in. I just took mine out, and it was hard getting out because of that. I saw where one guy took it off and it made it a lot easier coming out. Also what do you think about the metal shim in between the transmission and engine? Kinda bent mine some
@neilg3364 Жыл бұрын
Taking the driveshaft flange off makes it much easier.
@surikka9143 Жыл бұрын
Mine is almost back together, I just need to know the sequence of the bell housing bolts, is the one going into the starter port longer??
@hardcore4476 Жыл бұрын
Mike really desperate here! Where do I find neoprene O-rings instead of rubber ones?
@user-re4jf2sb4q Жыл бұрын
Hi is the process mostly the same for mark 6 dsg?
@edwardclark857411 ай бұрын
There is a shifter lever on top of transmission what position do you put it in when reinstalling transmission?
@naruttaanime94713 ай бұрын
Is it common problem for the manual transmissions only?
@east01la3 жыл бұрын
Do you have/know the webpage of cascade, so i can check out the price, for the dsg wet clutch kit? I need to replace my dsg transmission Wet clutches. Thanks in advance.
@Mikefngarage3 жыл бұрын
www.cascadegerman.com/
@Mikefngarage3 жыл бұрын
absolutely the cheapest and the absolute highest quality parts for vw.
@east01la3 жыл бұрын
Thank you so much. I being looking for dsg wet clutches, everywhere else wants an arm and leg.
@theacademy17344 ай бұрын
How do you remove the flywheel nuts?
@Mikefngarage4 ай бұрын
long triple square socket
@ivanvega282110 ай бұрын
Awesome guide! Would this be similar to a 2012 VW Passat TDI?
@Mikefngarage3 жыл бұрын
Thanks for your comments and likes. thanks for watching.
@Mikefngarage3 жыл бұрын
lots of stuff to know
@edwardclark8574 Жыл бұрын
Where did you get torque specs for Jetta
@Mikefngarage Жыл бұрын
google there are guys who post them on TDI club. all over the place.
@dragospahontu3 жыл бұрын
How much does a DMF cost in the USA?
@Mikefngarage3 жыл бұрын
part is 400 usd
@dragospahontu3 жыл бұрын
@@Mikefngarage in Germany a LUK set (clutches & DMF) cost ~400$. I guess this is why Asian cars are so popular in America.
@Mikefngarage3 жыл бұрын
@@dragospahontu wow clutches here are 500 German original usd and flywheel LUK is 400usd. I dont think they sell them as a set here
@dragospahontu3 жыл бұрын
@@Mikefngarage well it's the same for Japanese cars in Europe. A friend of mine had to wait 2 months for a rear bumper of a Mazda 3, when he could get one for a Golf in a day😅.
@Mikefngarage3 жыл бұрын
@@dragospahontu wow Probably all the tariffs and restrictions from Europe. Canada stuff is cheaper too. That is why lots of guys get stuff from CIP1 for classic parts that come from Europe. its like they are the money launders for European parts
@upupandaway56462 жыл бұрын
Did you change the dual fly wheel too
@Mikefngarage2 жыл бұрын
OH yea did that first.
@ennengb20103 жыл бұрын
this is pretty useless if you are trying to learn how to take your transmission out.
@gregroles692 жыл бұрын
if you don't follow this video, then you should NOT be trying it yourself.