FIRST START OF MY CHINESE 10 HP DIESEL !

[@oldironsfury]

Nice!!! No more gummed up carbs from the corn sauce we run in the old kohlers! Good choice, Diesel is the way to go ! 👍👍

[@dreamingbigcustoms9860]

Oh yeah and no messing with fuel mixture screws

[@lollife9203]

Did you ever figure out a throttle set up

[@franciscoaguirre6402]

Did you install the starter? If so what starter is compatible with this engine?

[@nascarsimracing1]

FINALLY SOMEONE ELSE WITH AN IDEA LIKE MINE!!! I'm wanting to put one of these on my John Deere 210!! And i want to remove the pullstarter, and instead have a huge ass flywheel to hand start it, like starting the 1940's john deere model A!!!

[@texaspoontaper5813]

I wanna do it to my 212 did you finish yours yet

[@nascarsimracing1]

@@texaspoontaper5813 i haven't done it yet, I'm sorry. Ive been having a ton of life drama, shit's been hell lately. I currently dont have time to work on the deere. Right now i gotta focus on keeping myself afloat.

[@texaspoontaper5813]

@@nascarsimracing1 more power to you man good luck

[@ciocanarusebastian6812]

Diesel Power😈

[@TROUROCKS]

i had to shorten the battery cables.. cut into them to find 9o percent rubber 1 percent copper .. nice big looking cables tiny little wire inside . im gunna open up the starter motor ill be looking for a rubber band

[@billbradley649]

Hey nice build !

[@dreamingbigcustoms9860]

Thanks but it's not even close to done

[@corndogextreme8887]

@@dreamingbigcustoms9860 where did you get the engine?

[@dreamingbigcustoms9860]

@@corndogextreme8887 ebay

[@courtneymurdick2055]

Where did you get the starter for that

[@BRIANVANDUYN]

Did you import this motor? Or ?

[@dreamingbigcustoms9860]

Bought it on eBay but it definitely came from China

[@matlombardo7415]

What pulley did you use?

[@TROUROCKS]

these are a 500 hour motor the Japanese one is a 3000 hour motor

[@logenanderson5825]

Where can you find a Japanese one?

[@kodisteffes8699]

Got close to 2000 on mine it’s a Chinese clone engine like this bought it in 2007!

[@jonnysnipes3123]

What happens when you get close to its end life, does the motor runaway and scream to the moon

[@GageLaBarber-q5z]

Fucking china

[@Waterboi-kd8bq]

Lawn mower engines cost $2,000 and dont last that long😂

[@jeanbaptistevallee4500]

Volume control on the next video would be nice...

[@2steelshells]

Please music needs to go or it least lower vol. Nice project!

[@brucebonkowski7253]

Why didn't you rotate the recoil to start from the seat

[@dreamingbigcustoms9860]

I'd like to see you pull that from the seat even with the compression release on it takes alot of strength to pull it over. If it was a 6 hp gas engine than I would have but no Way you are pulling that sitting down

[@kidddogbites]

​@@dreamingbigcustoms9860 You can, seen it done.

[@robertclark4929]

Diesels run at much lower rpms than gas.That would make everything like a mower deck turn much slower.

[@williamfurniss6442]

Easily countered by fitting a bigger drive pulley

[@Wingnut353]

Old mowers like this often had a low speed Briggs 10hp or something like that on them, in other words its already fine.

[@KuntalGhosh]

not the best idea to have all that exhaust blowing into your face , extend it with a flexible heat resistant pipe.

[@thewobblywelder8362]

Like an ‘exhaust’ pipe?