How I removed the broken off antenna threaded shaft that screws into the antenna assembly on a Toyota vehicle.
Пікірлер: 69
@anthazar85673 ай бұрын
Yes, thank you for this video. I found it useful for my broken antenna on my FJ Cruiser. If I can add just another little helpful tip... my dad told me to use a reverse 5/64 drill bit instead, and that worked in 1 try! As I was drilling in reverse because of the reverse drill bit, as it was catching on to the broken piece of antenna, it was being pulled out! 😮 by the time I realized it was already sticking out, and I could manually finish taking out the broken antenna piece. So, just another helpful tip for everyone 👍
@LeeB10225 жыл бұрын
Thanks for the tip. Went through the car wash the other day and forgot to take out my antenna! Low and behold it snapped and this video helped me out and saved me money! Replacement rubber stub antenna in place. Thanks!!!!!
@alivekicking5415 Жыл бұрын
Wooow! ThankYOU for making this video 👍 6 years later it's still helping people LIKE ME 😁
@krug77772 ай бұрын
Thanks for sharing this! So much better than taking apart my truck and replacing the whole antenna. And even better, after I sprayed a little penetrating solvent around the shaft, i didn't even need the extractor; the reverse drill bit threaded it out on its own!
@tonydee61094 жыл бұрын
Paul Eident you are a genius!! Toyota dealership quoted me just shy of $600.00 told me it was impossible to fix without a massive undertaking. I went on you tube and watched your video, then a quick trip to ace hardware $5 drill & tap set. 20 minutes later I,m on my way to pep boys, low and behold $16 antenna. $21 and I have am/fm again. THANK YOU.. Patience and perseverance paid dividends!!!
@pauleident18334 жыл бұрын
Great! I'm glad it worked out.
@yourlocalidiot694203 ай бұрын
The hell kind of ripoff quote is that?
@petekoutoulas91615 ай бұрын
Thanks! I had no idea how to get that sucker out, but using your method took only about 10 minutes.
@logansmith14995 жыл бұрын
Worked great on 2018 Tundra TRD. Save me lots of money, thanks!
@yourGhostrider5 ай бұрын
Thanks for the video man! I had the same issue and I saw your video and did exactly what you did and replaced my antenna. Thank you Sir, you’re the man! 👍🏻
@josephm405 жыл бұрын
Great video. I followed your directions on my 2013 Tacoma. Success!
@liquidsteel81315 жыл бұрын
That black piece is called a bezel.
@yoyatz5 жыл бұрын
Thanks! Drilled the hole off-center close to edge, but after finding the right gripping pliers I was able to unscrew it and install new antenna... on 2013 Tundra.
@jonprinceton79863 жыл бұрын
Instablaster...
@62WILDCAT2 жыл бұрын
WOW !! easy peasy ! Even I can do this ! 78 years on Earth 🌎 here ! Have used a drill & those vise grips too.
@TruckerBobKirby4 жыл бұрын
If your going to drill any right handed fasteners always use a left hand bit. They are available at any good industrial supply house. This way the fastener will reverse out with the drill and avoid ramming it further in.
@bobbyvillareal62839 ай бұрын
Same thing just happened to me. Thank you so much for posting this.
@windowpainter3 жыл бұрын
under 10 MINUTES! Thank you for the trick.
@billkuhels72255 жыл бұрын
Thanks for the video. This looks a lot easier than replacing the entire antenna assembly (or whatever you'd call it). I'm definitely going to try this.
@pauleident18335 жыл бұрын
Replacing the entire assembly is a PITA.
@MrMrfreedom15 жыл бұрын
@@pauleident1833 I tried to drill very carefully and slowly. Broke two bits and rounded out the top of the broken bolt vs. getting a nice hole drilled. Im screwed. What happens if I remove the silver slotted thing?
@pauleident18335 жыл бұрын
@@MrMrfreedom1 You may not have been using drill bits made for metal. The drill bit I used went into the metal very easily. You could try using a very small bit to get the hole started, then work your may up to a larger bit. I don't think the silver slotted thing comes off. If you try to take it off, let me know what you experienced.
@MrMrfreedom15 жыл бұрын
@@pauleident1833 Thanks Paul
@MrMrfreedom15 жыл бұрын
@@pauleident1833 for what its worth my antenna is broken of below the silver slotted thing. Ill go to the hardware store and find some small bits for drilling metal. Thanks again.
@toasty925 Жыл бұрын
There’s a lisle brand tap socket adapter that uses square drive that also works on those screw extractors. Works great and doesn’t cause wear and tear on the extractor.
@donjardon21034 жыл бұрын
Thanks, drilled about 1/4" deep with 5/64 bit and used a small extractor to easily remove broken bolt. Worked perfectly!
@maverickhistorian64884 ай бұрын
My first car had a broken ariel, I used a wire coat hanger to fix it. 😁
@marioconcepcion36943 жыл бұрын
Thanks for the vid. 98 4Runner all good to go now. 👍🏽
@johnvang55813 жыл бұрын
Which antenna did you go with? 2000’ 4runner here.
@yourlocalidiot694203 ай бұрын
Good video! Will try on my car
@jackjones94602 жыл бұрын
Well done! Thank you! That’s exactly what I need for my ‘02 Odyssey!
@62WILDCAT2 жыл бұрын
Thanks SO MUCH !!
@robertpalomarez4443 жыл бұрын
Good info on that.
@daleg93555 жыл бұрын
This happened to my Tacoma. I went through a similar process, but after removing the broken piece I found that none of the numerous thread adapters supplied with my new antenna would screw in. That seemed odd, so I tried the broken piece and found it wanted to fall into the hole, rather than screw in (fortunately I didn't let go). It seemed too small for the hole. But it definitely screwed out, wasn't pulled out. It's hard to tell but there appear to be thread grooves in the hole. So this is a mystery to me. I'm thinking some inner part must have dropped further down.
@pauleident33505 жыл бұрын
Bummer. I did not have this issue. I've done this on several Toyotas from 2000 to 2014 without an issue.
@belzeubub4 жыл бұрын
What size of drill bit did u use to drill and size of screw extractor. Stupid me got my antenna broken when i when to a new car wash in town..
@murrayent1able5 жыл бұрын
Is that an easy out tools?
@R3Elle2 жыл бұрын
just making sure before i try this, do you set your power drill into reverse gear when drilling into the center of the broken screw?
@pauleident18332 жыл бұрын
Forward(clockwise) when drilling the hole, then reverse(counter-clockwise) when backing out the screw. Don't use the drill to back out the broken screw, just your hand.
@douggray70134 жыл бұрын
Thank you
@randypantz90195 ай бұрын
Can you tell me what mm extractor you used? Im not sure which one to buy. Thanks!!!
@joebella86ify5 жыл бұрын
What is the black plastic piece called?......mine actually ripped off
@pauleident18335 жыл бұрын
kzbin.info/www/bejne/jpWpmXujqKaBipo
@MrBluesina4 жыл бұрын
well, as I drilled into the broken stud, low and behold, the drill bit caught on it, i was able to reverse the drill motor and it drew out the broken stub...didn't use an extractor bit. I guess I got lucky
@jhovanylopez18974 жыл бұрын
Joel same... just did. it right now😎💪
@Kana77825 жыл бұрын
What size screw extractor did you use?
@yoyatz5 жыл бұрын
I just removed mine with 5/64" drill bit and #1 extractor bit from Ryobi.
@mckinnoncharlie5414 жыл бұрын
Nice .
@brettsmith61145 жыл бұрын
Do you believe this method will work for a 2003 sequoia?
@pauleident18335 жыл бұрын
Possibly. It will work if it’s not a power retractable antenna.
@youdagoob2 жыл бұрын
Great in theory. No go for me. The antenna metal is too hard to drill dead center. After I did get a hole the extractor just cracked my brass housing. Oh well. I think I’ll try some plumbing fittings instead.
@zekeram1295 жыл бұрын
Why fix it when you can recreate it into a Gaia Beam
@kermitalexander66552 жыл бұрын
Cat wash got mines just noticed 😵🤔😵🤔😕🙄
@dougwhatmore71754 жыл бұрын
Or buy a 8 inch rubber antenna like I did. Never break again.
@pauleident47464 жыл бұрын
Good idea! Do you still receive a good reception with the 8" antenna?
@dougwhatmore71754 жыл бұрын
Yes I do. And look s cool
@linekona343 жыл бұрын
You have a link to the antenna?
@sairusk.h99963 жыл бұрын
Buy antenna wheel
@mikestephens8314Ай бұрын
If you drill it do it slowly
@davidw94034 жыл бұрын
That is dumb, but different! Congrats!lol
@gabicoful4 жыл бұрын
Did not work at all, had to get my money 💴 back, what a waste of time, got drill bit and extractor from Auto Zone and I just wait an hour trying to get the piece out 😡😡😡😡😡
@terrywinningham54052 жыл бұрын
Tried this technic and threads were stripped, had to cut off base and replace the entire antenna $205.00 at dealer. Terrible design by Toyota.
@suntzu9573 жыл бұрын
Yeah you dont want to scratch anything , then PROCEEDED to scratch the life out of the hood by placing a large heavy drill right on it. Couldnt watch after that.
@ThepDenNgoaiBien Жыл бұрын
is that a power antenna?? If power then ..it needs go up and down!! picture show you had power antenna then the motor run???.....If you let your radio ON all the time then..OK to do this way!