Don't use a torque wrench as a breaker bar. That will ruin your very expensive torque wrench.
@hwystitch8 ай бұрын
I cringed every time he used his torque as a breaker bar....
@e-dub80818 күн бұрын
Also thanks a ton on the rubber boot trick.
@partytimexxx89312 ай бұрын
Really wish you would've posted what kit to use. I'm dealing with this same problem on a Jeep Liberty and tried four different kits to press the ball joint in that don't have the right pieces
@CFITOMAHAWK Жыл бұрын
Hell, Dont let that heavy caliper hang from the rubber hose. use a cord or wire to hold it, not the heavy caliper and pads. GEEE!!
@CFITOMAHAWK Жыл бұрын
I have the same 2007 LImited. Mine had noises while turning. for a hundreds miles until i noticed it. Dont drive with bad noises. Torque them back very well.
@gladylagy35653 ай бұрын
Since you have a Jeep liberty 3.7 i have the same vehicle and im Experiencing an oil leak to my spark plug, whay could be the reason?. Does the jeep has a spark plug Gasket ?
@CrookedMustache3 ай бұрын
It does, they're basically giant washers, almost always included with valve cover gasket set. As they age they get brittle and can shrink and no longer seal the gap, thats when the oil starts to seep down to the spark plug
@gladylagy35653 ай бұрын
@@CrookedMustache okay thank you
@bumbofet772 Жыл бұрын
great video! trust me dude, add a 4 pound sledge hammer to your tool set to slam those suspension joints loose.
@e-dub80819 күн бұрын
What size socket did you use for the spindle nut?
@CrookedMustache18 күн бұрын
I had to check to be sure 35mm kzbin.infoFG-z7Bikqs0?feature=shared
@e-dub80818 күн бұрын
@ mine turned out to be 36mm but has to be a deep well socket. It’s still stuck tho I need a longer breaker bar.
@CFITOMAHAWK Жыл бұрын
After losing my first ball joint i grased all grease cups all over with a needle injector from a grease gun. I love my lifted liberty.
@angelcarrion54893 ай бұрын
Is this a jeep liberty 2006 ?
@HARPO1ME7 ай бұрын
Tke the upper ball joint nut loose first then hit the knuckle to pop the stud out of the knuckle .Then take lower loose then tie rod ends then axle nut and pull the knuckle with the hub off all together. Then press out the lower ball joint,
@rickwaa291911 ай бұрын
Watching you swing that baby Carpenter's claw handle was tough to watch.
@billymorris479510 ай бұрын
What is the axle nut size??
@gavaldi436110 ай бұрын
36mm I believe. @@billymorris4795
@total360AMC Жыл бұрын
My lower passenger just snapped going 100km, lost all control after front end hit the ground, slid into ditch, ripped out the axle, and the front fender, broke rim. No tell it was bad, or getting bad. Just snapped. Beef those babies up boys.
@CrookedMustache Жыл бұрын
At a crawl the sound and clunking was terror, at speed, I don’t even want to imagine
@jamesm22148 ай бұрын
2006 Jeep Liberty. My lower drivers side ball joint just snapped the other day. I've never seen that happen before. Luckily was going slow over RR tracks and pulled over immediately. Hate to think it would have happened on the interstate.
@jamalthigpen81293 ай бұрын
Why do ball joints just break
@CrookedMustache3 ай бұрын
@jamalthigpen8129 Best guess, the “ball side” of the ball joint lost all of its grease over time, and the heat build from normal movement with no lubrication made the steel fail catastrophically. The over boosted power steering typical on older jeeps definitely masked the symptoms
@ibntheibn10 ай бұрын
why you cut it off wow
@markhouston2253 Жыл бұрын
Don't need a press beat it out then very carefully beat it back in even and on the edge....
@ibntheibn10 ай бұрын
bro you could have used the c clamp press pop that old pice out and just press new ball joint
@stephenoshaughnessy2279 Жыл бұрын
The audio is unintelligible.
@MarioyDally Жыл бұрын
That sucks
@CrookedMustache Жыл бұрын
Yea bro, it sucked.👎 But at least we got it sorted and fixed. 💪