Great video as always. Can't wait for the next on.
@clifrusso21743 жыл бұрын
Very informative and detailed! Thank you!!
@terrymutant35814 жыл бұрын
I called my local BMW indie mechanic he seems trustworthy. Coding is different from Registration. If I replace my old battery with the same type i.e Lead acid, Coding is not required . The computer already knows how to charge to battery based on the last coding input. I can do a Registration with my cheap scanner.. But now I upgraded to an AGM . Since I don't have the proper scanners. I need to have the new AGM battery coded by him. He says I need to drop off the car for maybe 2 hours. (Lame ) He charges 1 hour labor $125 .
@abc123-d2t10 ай бұрын
Thanks for showing.
@maxford276 жыл бұрын
You do nice work.
@giancarlobonazzi3702 жыл бұрын
Thanks. But i need to know if is possible to change the Ah registered for a different value. The original was a 105Ah and the new is 92Ah. Then displays message about consummer disabled. My case is in a 2013 640i F06.
@FlashPerformance2 жыл бұрын
kzbin.info/www/bejne/hp-5mGuBeKtqgac
@achristian70152 жыл бұрын
1:27 it does not call for the CCA of the battery. It needs the Ah, the capacity and as shown at 4:36.
@napboy812 ай бұрын
Thank you.
@werlisadle18 ай бұрын
Geschafft..Austria💪😘
@E2SPerformance Жыл бұрын
What about kimbolen? Can you do a reset with that? Say like the k6 k7 or k8? What about all the launch? I need a scanner but want one that can do this reset and also keys
@TattedTommysTv7 ай бұрын
So is this sane as basically what they say a reset cause I replaced my battery in my X5 and it keeps going into limp mode someone told me I had to register my battery would this cause it to run poorly?
@a.c.e.75682 жыл бұрын
At 4:33 it would have been nice if you selected "Enter battery replacement: Higher/lower capacity" to see if you can actually enter a 2 or 3 digit Ah rating and then the battery type (wet, AGM, etc). instead of a list of Ah that Autel provides. By the way, those scanner screen shots look identical to that of an iCarsoft. These scanners are like batteries, made by a couple of companies.
@FlashPerformance2 жыл бұрын
Here is a video I did with the MS908P that I did change the battery type and Ah.
@a.c.e.75682 жыл бұрын
@@FlashPerformance Were you supposed to add a link to the video?
@FlashPerformance2 жыл бұрын
@@a.c.e.7568 kzbin.info/www/bejne/hp-5mGuBeKtqgac
@achristian70153 жыл бұрын
3:06 what do you mean by "it charges the battery harder"? You can only set the battery charge voltage and this is dependent on the battery type (FLA, AGM, etc) and temperature. All these companies are over thinking this. I can bet you you'll never get the 14 and 16 years battery life cycles I got in my cars and I did not have a BMS in them.
@eoinhenderson18196 жыл бұрын
top marks great video,,
@mplscarsales66522 жыл бұрын
Hi I have a 2013 Cadillac ATS AWD Premium the Battey saver 70k miles light came on dash I. Took battery out had it fully charged checked load tested it was good .Do I have to have this scanner to reset BMS ? Also will this Scanner show if alternator has failed so I don’t have to go wasting time on other parts like fuses ect ? If it’s not reset will battery level just keep going down cause BMS thinks it’s still old battery in there ? Thank you
@FlashPerformance2 жыл бұрын
You only need to do this process if you are replacing with a new battery, just charging the battery will no require a reset of the BMS. For the Alternator you will need a battery tester, I use this inexpensive one from TOPDON, www.topdon.us/collections/battery-testing/products/bt-100
@kodygomillion59832 жыл бұрын
Just bought the new mx808, Would you be willing to help me re register the battery through this specific product ?
@FlashPerformance2 жыл бұрын
If you need help with the process you can reach out to the Autel support team. They can assist with the process. Here is a link of someone else using the Autel to do a battery registration as well. kzbin.info/www/bejne/f2nVdnysYt2Cm7M
@chefenriqueavargas33265 жыл бұрын
Great video my friend, very informative. Question? If I installed the battery last week, and just bought the scan tool today, would I need to unplug the battery and reconnect it in order to register it? Because it's not letting me register it as is. Thanks
@FlashPerformance5 жыл бұрын
No need to disconnect the battery, you can do the BMS registration anytime. The sooner the better. Make sure you do all of the updates on the tool before attempting the registration.
@chefenriqueavargas33265 жыл бұрын
Thank you so much, I was able to do it. It showed that a battery has never been registered on it. It's amazing, the day after I registered the battery the car was driving better, and a lot of the little problems I was dealing with are gone. Thanks again for the amazing video.
@ksg78214 жыл бұрын
Good.
@ricardorodriguezortiz24514 жыл бұрын
Question will this scanner work with valvetronic relearn system on X5 2009 30i xdrive n52 engine
@3lsalvy4life5 жыл бұрын
With a TS608 can I write a TPMS sensor ID into the PCM. Like on a Toyota? Or do I need a MaxiSys, looking not to spend a lot on a MaxiSys... thanks
@FlashPerformance5 жыл бұрын
Yes exactly, this tool will take the sensor IDs and write them to the PCM. It is a simple process. You can also do it with the TS508 kzbin.info/www/bejne/baPWq4aigLCtl8k
@hansnilsson82363 жыл бұрын
Is it any option for AGM type battery instead of Lead acid
@FlashPerformance3 жыл бұрын
To change from a Lead Acid to AGM you would need a more powerful tool to code that to the vehicle. MS908P, MS908SP. MSElite, MS909, MS919, Ultra can do that feature
@joseloslopez9855 жыл бұрын
Thank you so much for your video, I hope you can help me flash performance, my costumer call me and tell me, him replaced his own batery, but not use scan tool, now in this car, power windows turn signals, high beams, interior lights is not working, is 2013 BMW. I need reprogram some module or I need do some prosses?
@FlashPerformance5 жыл бұрын
Did you do the BMS reset as I showed in the video? If not It could be because the battery wasn’t reset and now the car thinks the battery is bad and it’s conversing power to make the car drive.
@joseloslopez9855 жыл бұрын
@@FlashPerformance thank you so much for your help. I have other cuestion this Autel ts608 in your video, ts608 can read codes and and see life data for engine? Thank you so much again. 😊
@FlashPerformance5 жыл бұрын
@@joseloslopez985 Yes, Read and clear codes and view live data in all modules.
@tromponist5 жыл бұрын
@@FlashPerformance $295 per year
@jasongins5 жыл бұрын
Does the "enter with higher/lower capacity" function work?
@FlashPerformance5 жыл бұрын
Yes, I didn't have any problem with it. After this video I installed a better battery in the vehicle on this video: kzbin.info/www/bejne/hp-5mGuBeKtqgac
@JosephusXIX4 жыл бұрын
Are MaxiSys and Autel the same company?
@FlashPerformance4 жыл бұрын
Autel is the manufacturer and engineers, Maxisys is the tool brand name. It is the Autel Maxisys scan tool. This tool is the MaxiTPMS brand from Autel.
@JosephusXIX4 жыл бұрын
Flash Performance Ah okay. I bought an Autel unit earlier in the year, and the interface looks the same, and then you mentioned the name.
@unemployedgamers15734 жыл бұрын
Won’t let me register the battery please help :( I followed your steps and it keeps saying ibs causes
@darylkitchens31493 жыл бұрын
Did you get it to work? I tried this morning and having the same issues. I can see the voltage and the first battery info.
@darylkitchens31493 жыл бұрын
I figured it out. Thanks.
@darwincabrera15675 жыл бұрын
Is this key programmable also??
@FlashPerformance5 жыл бұрын
Very little. It has an icon for key and immobilizer but it is very limited.