Definitely one of my favorite quads. Wish it had a bit more kv but it's durable. Yours should have the updated tune. The filters where setup wrong for bidirectional dshot so you may want to check that.
@MiniMicroFPV3 жыл бұрын
Oh hey thanks for the tip! I’ll check that. I wonder if that’s where some of the small vibrations were coming from?
@RubyS.13 жыл бұрын
@@MiniMicroFPV yeah I had same thing which is what got me looking. They had the motor poles set to 14 should be 12 and the notch width they had at 8 should be 0. It's good to go now
@MiniMicroFPV3 жыл бұрын
Fantastic, thanks! I will change those.
@bradleybeaudry89353 жыл бұрын
I like how you always show the quad taking off, and landing. I did not know this has anti collision strobes installed from the factory. It is nice to see manufacturers offering expresslrs in BNFs. Great review, and flight. Thanks for the great content.
@MiniMicroFPV3 жыл бұрын
Thanks! Hehe yep, it's a neat one!
@kendrickfpv41393 жыл бұрын
Thanks for the review!
@dragonclawfpv3 жыл бұрын
Nice little quad👍
@SpikeJonesTheCr0oked3 жыл бұрын
Hey will you be reviewing the Gnarlyfpv Zero? I have been loving the 40mm version, but would be interested in your take on it....
@MiniMicroFPV3 жыл бұрын
Hey thanks for the question. I've actually been thinking about it but I need to get some gear to run in the frame first. I was looking for a Mobula6 with ELRS to get the electronics from but it's not in stock at the moment. EDIT: Actually I take this back. After looking closely at the Mob6 ELRS components I don’t think it would be a good fit for this frame with the motor plugs and USB location. The intended Nanohawk gear swap would be much easier so that would be the path I take if I do.
@turboomni8483 жыл бұрын
Nice review. I just got one and get around 5 to 6 minutes on a 450 mah. Mine does not have the white flashing leds. Maybe I have them and have to turn them on??
@MiniMicroFPV3 жыл бұрын
Oh cool, thanks for the info on your flight time. About the lights, hmm. I didn’t do anything to turn them on in BF or elsewhere. Mine just seemed to come that way. I’ll investigate.
@turboomni8483 жыл бұрын
@@MiniMicroFPV Although I got my Nano only about a week or two ago my frame is different than yours in that I have no provision to change the battery to the other position as there are no tangs for it. Also I see that mine has different pids than yours but it was set on profile 2,,profile 1 has the updated pids and I will try. So I wonder if the strobe LEDS are new and not on mine. No biggie though it may help to find it in grass. But be that as it may I got many flights in today on apparently profile 2 pids and this thing is a hoot. I will change to the updated pids and see what happens. Also just to add on the config tab I found on the right side near the top a setting for motor poles and a number you can set. It is set to 14 [14 magnets] I counted only 12 on these motors,,, I set it to 12. Will it make any difference,,who knows.
@MiniMicroFPV3 жыл бұрын
@@turboomni848 Hello. Yes it seems the change to the battery strap mounting, etc came in the 1.2 version of the frame. Also you are absolutely right about the number of motor poles being incorrect. fpvgirl pointed this out a couple posts back and there is also the Dynamic Notch Width should be set to 0 instead of 8. I've changed these things but haven't tested it yet but will do a follow-up video once I do. I'm pretty sure switching from 14 to the correct 12 poles will eliminate the vibration I was having at low RPM.
@turboomni8483 жыл бұрын
@@MiniMicroFPV Looking forward to your results! I have also heard about Project Mockingbird doing a tune on this little rascal too.
@TheAleman033 жыл бұрын
Where can i solder crossfire receiver can i use pads labeled tx2 rx2?
@kxdmotovlog68982 жыл бұрын
If I connected my drone to the Fs-x14s transmitter, can you tell me the next step? Do I need to keep the receiver on the drone or is it ok if I take it off?
@kxdmotovlog68982 жыл бұрын
ut i have big problem with drone because I put the battery in several times the lights do not turn on and if I wait 2 hours and the lights come on Please tell me what to do to make myself?
@TweakRacer3 жыл бұрын
Great review. Given how wide this frame is, maybe the stock longitudinal lipo mounting makes more sense balance-wise?
@MiniMicroFPV3 жыл бұрын
Hehe it's possible but the battery wires were too short on the GNBs so I kind of had to run them sideways~~
@TweakRacer3 жыл бұрын
@@MiniMicroFPV Just finished watching the full video and you totally mentioned that. Like you said, maybe the "Flywoo" branded lipo has longer leads. Very thorough review, as always. Cheers!
@kxdmotovlog68982 жыл бұрын
Hello, i have big problem with drone because I put the battery in several times the lights do not turn on and if I wait 2 hours and the lights come on Please tell me what to do to make myself! please help meeee i need!
@ChrisParayno3 жыл бұрын
I wasn't aware there was a v1.2.
@MiniMicroFPV3 жыл бұрын
Yeah I think it’s mostly small changes to the frame and the addition of GNB27 connector. Oh and the tune might be slightly updated~~
@ChrisParayno3 жыл бұрын
@@MiniMicroFPV thank ! I stumbled on to your channel a few weeks ago. Great info. You got my sub.