FORCE Nitro Engine Break in Process | VRX 1 Truggy | banggood.com

[@TheRCBiker]

Be sure to check out this car. Link is in the description - Plus a Discount Code too!

[@Gavs_rc_hobbies]

One little tip for engine break in. Before you start the break in, take the glow plug out, slowly turn it over untill you can see the piston at BDC, then mark that point on the flywheel with a permanent marker, so then after each run you know exactly where BDC is. 👍🏻

[@TheRCBiker]

Nice idea!

[@bartoszabratanski3425]

Nice truggy! Great video, the break in process does take a bit of time but it’s worth it in the end !!

[@TheRCBiker]

Sure is! :)

[@BcHmF]

Nice! The Force Engines are great. Looks like you did not got much of a problem with this one so far.

[@TheRCBiker]

yes I like Force engines :) no issues so far

[@guinnessdublin4669]

Another great video, it’s great when the new engine suddenly comes into life after proper break in! 👍🏻

[@TheRCBiker]

It sure is! :) Thanks for watching

[@amanvirdi3305]

You have been going strong for 10 years well done 👏

[@TheRCBiker]

Nearly 12 years actually!

[@amanvirdi3305]

Wow that’s amazing 🤩

[@xl_itzdieselz_lx8617]

how do i know what type of gas to put into that rc vehicle ?

[@harout1211]

Hello thercbiker can you please help me with the factory reset settings for this engine . I can't run my engine and want to put back to normal Thank you so much

[@TheRCBiker]

I don't know them off by heart but this is the Force 28 engine so if you search for the factory settings online you will find them :)

[@BlvlWmpower]

The two things about nitro: setting up your throttle/brake linkage so it doesn't stall. when giving brake or idle. Air you have any problem starting the rc cold, unscrew the glow plug and pull the pull start a couple times to "spray out semi burnt fuel". Put plug back in and a finger over the carb, pull 2 times to start fuel flow into the engine, it should just about start in 2 pulls if you do that. Needs that fresh fuel to ignite much easier and not have to burn off oily burnt fuel left from the last drive. If you can't start after running through a tank, your engine is probably overheated and burning off fuel from the heat, faster than the engine can suck fresh fuel in. Once you do all this, you will get a better experience than spending most of your time fucking with batteries and chargers that costs multiple hundreds of dollars if you get decent batteries and charger. This doesn't even count programming cards or more than three batteries. I haven't done it in a while, but used to drive kyosho 1/8th. Just make sure to get a good engine, because .21 race engines can often be faster than significantly bigger engines in that their powerband kicks in more like a dirt bike pulling wheelies at 30 mph across a grass field.

[@chrisracer2007]

If my car has been set for a long time is it good to break it in

[@TheRCBiker]

No

[@RudeboyMoto]

Need to get some bashing done to see how it holds up as thinking about getting 2 of these, one for me and one for my son.

[@TheRCBiker]

Yes bashing video will come soon

[@zachh3293]

How long did each tank last?

[@TheRCBiker]

10-15 mins

[@ryze7810]

i bought a force .32 nitro truggy, the engine exhaust gasket is half cut and it doesnt prime the carb however, when i blow in the fuel tube it works and nothing seems to go wrong when i use it, is it ok if i leave it how it is right now? because it seems to work fine

[@TheRCBiker]

If it's working then fine, you don't want any oil leaking from the back onto the pull starter though. Leave it and run it but have a new one on order!

[@ipperurc5216]

Nice that you are back! I have loved your reviews and content!

[@TheRCBiker]

Thanks! More coming :)

[@alexcrosse9970]

How do you buy replacement parts for this?

[@DYLLY0456]

On banggood.com

[@TheRCBiker]

Hi Alex, banggood have a good spares supply. or, Nitrotek in the UK used to sell this and have good parts stock

[@TheRCBiker]

@@DYLLY0456 Yes, or Nitrotek

[@GrimReaper-sl9zo]

Where would i get gas for a force .18 engine?

[@TheRCBiker]

It runs on Nitro :) Online, model shops

[@flurpmcderp6807]

Do you have to put the engine piston at the bottom every time or only during engine break in ?

[@TheRCBiker]

All the time is a good idea :) Especially if not using it for a while. It prevents the piston from becoming seized within the liner.

[@flurpmcderp6807]

@@TheRCBiker so you just pull the cord until it becomes harder to pull ?

[@RonanKearney1]

ooooh I want one. Canny wait to see how this one bashes. Thanks dude

[@TheRCBiker]

Hopefully coming soon!

[@josephromo4497]

Can you do a quick video on how to set the End Points on the throttle servo? I had to replace the servo for my exceed forza.. and cant quite get the servo dialed in properly.. I really enjoy watching your videos and I think you do an amazing job on explaining issues and solutions

[@TheRCBiker]

Hey! Thanks for the kind comments. I can... But it depends what radio you're using. EPA is simply just a turn knob adjustment on many radios which lessens the travel of the servo. What issue are you having?

[@guinnessdublin4669]

What glow plug make/type did you run this engine on my friend?

[@TheRCBiker]

I can't remember but most likely a cold one with 25% nitro

[@tonycruz7596]

Love that truggy!

[@TheRCBiker]

Me too! : )

[@rajivk4705]

What happens if we dont do these process and we just run it on full throttle?

[@GODLIKEZ490]

your engine wont last long

[@TheRCBiker]

It'll lose compression and won't last long! having said that, I have read stories of people not breaking in their engines and yet they've been fine

[@tonycruz7596]

Hello, I need some help picking a new clutch bell. I have a Hobao Hyper 7 with a dynamite big red .28 I use it for bashing on and off road. I had a 13t Hobao clutch bell on it but every tooth has a perfect cut out from the teeth of the spur gear. Idk how that happen but it did, do you have any recommendations?

[@TheRCBiker]

Hi Tony, I'd stick with the Hyper one as the clutch bells are car specific rather than engine specific, I can only assume maybe the gear mesh was set incorrectly, probably too loose, which has caused what you're describing!

[@tonycruz7596]

@@TheRCBiker ok I'll do that, and I'll check the gear mesh. Thank you so much your awesome

[@TheRCBiker]

no worries!

[@joshchatwin8179]

Yes bro keep it up brother waiting for that kyosho video to drop bro

[@TheRCBiker]

It won't be just yet ;) I need to catch up with all the ones I've got sat waiting to bash first!

[@orozimbogoulart7297]

Where do you find this empty car parks in England? Im sure is not in London 😁

[@TheRCBiker]

You do during lockdown! 😁

[@curtiscrick8837]

Music to my ears 🤟

[@TheRCBiker]

Sounds nice right! :)

[@plewsford]

Great vid. What engine temperature have you been working to on these warmer days? I've seen between 85 and 98c. Do you think that's too hot?

[@TheRCBiker]

Anywhere between 80-100 is fine. 100-120 also OK but I would be keeping a close eye on it . Over 120 and you need to worry :)

[@plewsford]

@@TheRCBiker That's great. Thought as much. I've been running the engine with a bit of smoke on low and top speed so it shows that the engine is getting enough lubrication. Question about the Rovan Baja. How long did it take to arrive?

[@TheRCBiker]

Well I got lucky and managed to grab one that was available at their warehouse in Spain, it literally came within 48 hours, I was very impressed especially with all the COVID associated delays. They sent me this truggy which came from the China warehouse and it took between 2-3 weeks I believe.

[@adamlitho6448]

hi again great video

[@TheRCBiker]

Hey, thanks! :)

[@hypercriticalone]

I thought you would comment on the rc copter i finally got

[@TheRCBiker]

I didn't see the notification, I'll check it out now :)