Thanks for taking the time to make that, the use of hose to protect the threads is a great idea too.
@markreilly4562 жыл бұрын
Great Video! I have an old Ford 555 with the same problem. After watching your video, I gave it a try. Worked like a charm! Thanks.
@Roubian1 Жыл бұрын
Thank you! This saved me hours of trying to figure it out.
@ASTAROTH136664 ай бұрын
I have a ford 550 from 82 or 83 and have a constant hidrofluid leak,the mechanism of it looks very similar to yours.does the leak happen because solely of thatt rubber boot/seal or it might be something else?also any idea if i need to drain the hidrofluid? Totally new to ractors so any tip is greatly appreciated.
@falarequestretvjorgecarval42637 ай бұрын
Hello . Could you help me ? Bought a 1975 Ford 5000 and did all the recovery myself . But there is no power in the arms . Cant lift a 300 kg hay bale. Have no leaks on the arms and replaced the rubbers of them. I was told it was the hidaulic pump. Where is it the hidraulic pump ? And what can I do . Thank younso much
@krishritsumret35583 жыл бұрын
Good job.
@juanhernandezreyes89512 жыл бұрын
Great job!
@stevec96533 жыл бұрын
The inner part of the boot needs to be pushed another 25mm up the rod it sits in a recess
@almightyamateur36483 жыл бұрын
kzbin.info/www/bejne/eJ28imScm8Zjj7cm40s
@nickmaggio40192 жыл бұрын
what is the part number and where did you get it ?
@mrmobius20002 жыл бұрын
I am doing this job on my 4610SU. The left side seal replacement went just as is shown in your video. I have ruined 5 seals trying to replace the right side seal. Using calipers, I have determined that the right side hole in the rear axle housing is about 1/10 of an inch too small. The relevant OD on the seal is 1.977 inches; the ID of the hole is 1.875 inches. I believe the hole in the rear axle housing is out of spec. Have you or anyone else encountered this dilemma? It seems my options are give up and get a different tractor; find a replacement rear axle housing and install it; remove the rear axle housing and find someone who can machine the hole to spec. Replacing the axle housing or having it machined are both huge jobs that I am pretty sure my local New Holland dealer would decline to perform, citing staff shortages and the cost/benefit of fixing a 1981 4610SU. Any other options are welcome. So far this debacle has chewed up a week for a job that should take a couple of hours at most.
@almightyamateur36482 жыл бұрын
No sorry, did not encounter any problems like that. Looks like it’s the same replacement part number aswell for both models so something seems off with your specimen. And there is nothing left over like a ring from another old seal or something stuck in the hole? All I can think of is to somehow squeeze the seal a little bit to reduce it’s size, but that might ruin it aswell. Or maybe another seal with a smaller diameter for another tractor model. It’s a long shot.
@donames69417 ай бұрын
Put your seal in the frezzer overnight, and press the seal in after it warms up push the rubber over the shalf
@juanhernandezreyes89512 жыл бұрын
Does all the hydraulic oil need to be drained or not? I have Ford 6600 80'
@almightyamateur36482 жыл бұрын
Can’t say because I’m not familiar with that model. This one had already lost quite much rear end oil. You could drain a gallon or two and put it back in after, if it looks clean and usable. You could also park the tractor on some wooden blocks to tilt it sideways that way you get more space to work with and the oil flows to the other side. Just be safe.
@emmanuelmutai46032 жыл бұрын
How do get ford 5610 manual??
@timtalaski59042 жыл бұрын
I need a video on how to repair the PTO brake on a 5000
@pashootist53542 жыл бұрын
These might help some. Ford 5000 PTO clutch pt1 kzbin.info/www/bejne/iJesgYhth7Sdf9k Ford 5000 PTO clutch pt2 kzbin.info/www/bejne/pmfJhXWriq2UbLs
@timtalaski59042 жыл бұрын
@@pashootist5354 thank you for the info, will give me a lot of confidence when I tear into mine. I appreciate it
@kedronpful3 жыл бұрын
Yes seal needs to be pushed way on up the rod and seated in the groove.... That's gonna leak
@almightyamateur36483 жыл бұрын
kzbin.info/www/bejne/eJ28imScm8Zjj7cm40s
@kedronpful3 жыл бұрын
Yes that's it!! Didn't see that before.
@jackdurham5601 Жыл бұрын
@@almightyamateur36484:40
@donames69417 ай бұрын
You didnt show pushing the seal on to the rod yor way it will leak