Hi, any advice or help to put the new engine back in and make it fit? I tried but I couldn't. I appreciate your help.

Great tips, super helpful! Gotta replace a rear main seal and I think pulling the engine will be easier than dropping the transmission.

Great video thanks! If I just want to remove the transaxle, I would use an engine hoist to support the engine, drop the subframe and unbolt the transaxle from the engine?

Hey can you show how to replace the litle motor which moves the light up and down?

Thank you for this one and the one taking the bumper off. Mission accomplished. our 2013 model is now 12 years old, so some of the plastic connectors broke on me but luckily I had bought some on Amazon, some of which worked.

Thanks for the tutorial. Got what I needed from it, and changed the starter on my dad's 2012 v6 automatic today in about 1hr. The top bolt was harder to loosen than the bottom one. Once I was in there, I thought I would need a deep socket (I didn't bring one) but my regular 13mm 6 point socket was able to fit snuggly over it (just barely, it bottomed out right at the flange) with my 3/8" 15" breaker bar. I jacked up the car pretty high. The front tires were about 6" off the ground. I was able to get the bottom bolt loose with just a 13mm straight ratcheting wrench. My dad was stoked to be back on the road and was happy that at least one of his sons knows how to fix cars. Lol.

Really helped! Thank you for creating it! I tried it today. But my issue that I have the wrong part. The years above 2010 maybe the same - mine has the diamond shape low pressure house inlet. And the hp is mounted sideways not on top. The banjo bolt sideways.

Thanks, but you keep saying excess like access. 👍

Very well done instructional video sir. Direct and to the point with good lighting and video with proper choice of tools and sizes. Thanks for sharing!

What was the torque tool you used?

Thank fuck you posted this video

Thank you

Hi. Should I leave the car in Park before disconecting the battery or put it in neutral?

Outstanding video! Thank you so much. Going to get at it in the spring!

I'm about to just destroy all of the plastic holders it's so annoying but this is a great tutorial

by any chance, do you know what size bolts are used for the starter? trying to install one on my mustang and need to know what size the 3 bolts are

Good

Any reassembly video? Would help out a ton of people, just saying 😊 thanks for the tear down video, great work!!

What to do if the clip which goes into the hole is broken off from the bracket below the fender

Thats very clever

Thank you

I'm getting ready to do this myself using your method. How long did it take you to change these out? My 2016 appears to be on the original spark plugs with 142K miles on it. So, it's definitely due.

Having just done this few times, small time saver for those just removing the headlights - no need to remove 8 bottom screws that hold the splash guards, they are elastic so once you remove all other bolts and clips you can just put the bumper down on the ground and they will bend without damage and you'll still have full access to the bottom headlight bolts. Thanks for the video, still super useful 11 years later.

Just wanted to thank you for the excellent video I have a 2015 toyota camry and my starter went bad I watched your video and I was able to replace my self thanks again

Excellent

This is the same for Mazda Ford fusion and Mercury Milan Mercury Milan. I think all the parts are pretty much interchangeable to.

I've done it just like you showed 3 years ago and today my ball joints seem tight still but when I did mine I removed the ball joint boots and really filled them them up with more grease than they came with and I preloaded all control arms as shown and when I had to change the intermediate CV Jack shaft I noticed after freeing up the top ball joint and taking the strut loose from the lower control arm to get the control arm down enough to move it to the side to get the CV shaft out that my lower control arms seem to move up and down pretty freely but the bushings look good but it's like the guide through the bushing has broke loose from the rubber bushing is that normal? I was thinking that they would still have some control to stand up without any pressure pushing down but they fall all the way down so I take a light and I'll look at that guide to see if it's moving but I'm moving the arm up and down it seems stationery but the rubber is free no longer bonded to it. I don't usually have a sense of loads on my front end pretty much just a driver.

Thank you! Your video was a lot of help with removing my Sienna engine!

do you have any diagrams. I can't find any online. the lowest wheel on my q5 is lose and I'm trying to find the correct part to order.

Hey one quick question. Some rear bumper have parking sensor are they the same as these one. Or does it have a plug I have to unplug ?

Good job, thanks for video.

Simply perfect. Well done.

Is this the same for 2014 Subaru Forester. It seems easier with this set up. Saw other videos without usung the swivel and having to pop off extension midway thru changing

Once every 100K kms, better get dealer to do it, doesn't look easy, especially if you are not skinny.

TY for video

It’s not getting replaced without removing stuff out of the way.

Nice illustrated video. Keep up the great work.!👍

4:55 that bolt is in backwards to begin with. It should go from front..to back. Turn the nut, not the boltm

Very straightforward and to the Point great video

Hello , is it possible to change the lights from Mazda cx5 and modify from mazda cx5 2015? The rear and the front??

I need you man , amazing

Speed at 1.5x just helping you guys out

Is that evaporator the same exact fot the 06 tsx?

Will the engine not fit out the top?

Is it the same procedure for 2023 model?

The cleanest video ever

Just did this, I didn’t have a a universal wobble and I had the stick a 1/4 ratchet with the m12 tq and get it from above, thankfully I have baby hands and was able to get in there😭🙏🏽

My daughter damaged the lower bumper (the black part). Is it possible to just remove that black piece without dropping the entire bumper cover?

Sir, thanks much. Really a remarkable video. God bless you

Thanks for the step by step instructions I wouldn’t have taken the taillights off if I didn’t see this video and this would’ve save me extra time and effort.