In this video, we show how the vane oil pump on a p5at/p4at breaks and how to install the upgraded gear oil pump. Parts fitted www.yd25.com.au/index.php/yd2...
Пікірлер: 28
@sparke58520 күн бұрын
Hi, Firstly thanks for all your efforts with the great informative videos! I would really appreciate some advice, I am in Thailand and bought a 2014 ranger wildtrack 2.2 120,000km. The ford dealership just links to their laptop and tells me there's no problem. Symptons: - lose of power when starting to accelerate in low gears - twice i have been approaching/going up a steep hill changed down to 2nd had no power and then down to 1st and also had no power and the vehicles stalled - slightly rough idling (only a little) and also a shudder when turning off the engine From everything I have seen online I am thinking I need to clean and blank off the EGR cooler, but I would really really appreciate some professional advice! Thanks so much in advance!
@ruscador16 ай бұрын
getting mine done next week yipeeee
@EliasRivera-wn9ge Жыл бұрын
Consulta pera que elimina la cañeria de aceite que va de la bomba al block ?
@Mike--K Жыл бұрын
Nice instructional video. To be clear, is the new gear pump self-priming?
@yd2532 Жыл бұрын
Yes
@Mike--K Жыл бұрын
@@yd2532 Thank you!
@marcusbarnes592910 ай бұрын
Why do some of the geard pumps for 3.2 ranger retain the oil feed and some geard pumps do not.. Whats the difference of blocking off the oil feed vs retaining the oil feed back to geard pump?
@greg105 Жыл бұрын
So how do you remove the sump after removing all the bolts while the engine is still in the car? The sump is virtually welded to the block and almost impossible to break the seal?????
@ProperFNQ Жыл бұрын
Is that a yd25 oil pump?
@greg105 Жыл бұрын
Is it possible for you to do a video on how to do this job whilst engine is still in the car? Would be greatly appreciated. Thanks
@bundj12and36 ай бұрын
😂
@georgeliquor29315 ай бұрын
It is possible on the ford transit, a bit of jiggling about to get the pick up off then the sump slides out revealing the oil pump, not sure about other vehicles, it all depends on how close to the sump the cross member is
@RIPPERTONАй бұрын
But does the Standard engine have a oil pressure relief valve or does the new oil pump have one. Judging by the castings on the new pump there is an internally recirculative pressure relief circuit. 4:33 that cylindrical casting is a pressure relief valve ON THE OLD PUMP !!!!!!!!. Why T F does a variable oil pump have a PRV ?
@mwnciboo Жыл бұрын
Hold on... I fit one of these and no more 10minute *Panic* oil changes?
@yd2532 Жыл бұрын
Ye you can drain the oil for as long as you want
@vonlogan12 ай бұрын
Is the 12 mm bolt an M6?
@chillingwolf11 ай бұрын
Were do u get this pump from do you have a part no and a website or anything to buy cheers
Will this oil pump upgrade cause higher oil pressure at idle
@currencyjon0111 ай бұрын
im waiting on my geared pump to arrive, Had ordered that before i even picked up my Wildtruk, (2015 model, S/Hand} slightly higher would be nice but not too much to cause seals to leak.
@noahridesmtb588611 ай бұрын
I found out that the issue I was running into was that the vacuum pump was not engaging with the camshaft because when I reinstalled the vacuum pump it was not aligned with my camshaft and pushed the camshaft forwards 4mm in the head. that's why I commented asking if the pump would cause higher oil pressure as I thought that there was too much oil entering the vacuum pump causing it to not have any vacuum.
@nickybunka352910 ай бұрын
What's the part number of the pump your using please.
Can you do this job while the engine is in the vehicle?
@yd2532 Жыл бұрын
Yes
@georgebets4128 Жыл бұрын
Let's see you do that?? I believe cross member needs cutting or engine removed. Love to see it done with engine in car and I will be doing it next week😊
@sername1793 Жыл бұрын
Так то и любой сможет заменить, а ты на месте не снимая двигатель попробуй!