Can am renegade 1000 assembly

  Рет қаралды 24,563

Four wheeler Doctor

Four wheeler Doctor

Күн бұрын

This engine came off a 2016 XMR 1000 can am renegade. This engine would run but acted like it had a lower than stock rev limiter. It also had some noise coming from the bottom end that sounded like it was coming from the rear cylinder but it was actually the front piston's rod bearings that were spun. I had the crankshaft machined and new bearings installed. I also installed some MR RPM drop in cams. This engine is very similar to any of the 1000cc engines that can am puts in the outlander and the commander.

Пікірлер: 26
@aulobito
@aulobito 2 ай бұрын
Muchas gracias......!! Saludos desde jalisco Mexico.
@micflynn1
@micflynn1 4 жыл бұрын
The valves cleaned up nice. Pro tip for ya, when you need clean carbon off the valves I use Oven Cleaner! Spray on foam it up and be Amazed as the Carbon washes away! 😁
@FourwheelerDoctor
@FourwheelerDoctor 4 жыл бұрын
I will give it a shot on the next one.
@binggo2787
@binggo2787 4 жыл бұрын
great video nice job.
@travishethington8824
@travishethington8824 3 жыл бұрын
Great video ! Have two motors im about to start on.
@martywhitman6773
@martywhitman6773 2 ай бұрын
Great video but never got to hear if it ran good and if it fix all the problems. Was there any issue with the rebuild and did it run strong?
@jakelandsberg5917
@jakelandsberg5917 2 жыл бұрын
2 years later, how is it doing? Also do you recall what rod bearings were used?
@nwags357
@nwags357 Жыл бұрын
Do you happen to have a link to the sprocket holder tool you mentioned versus using the screwdriver
@cardinalbaycustoms2702
@cardinalbaycustoms2702 2 жыл бұрын
What bearing would get tight with heat? Iv got a motor that won't start when Hot. Tight to turn clutch by hand. Why would this happen any help would be great thanks
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
I could be either a rod or crank bearing. I have never had one do that but also I don't work on many can ams.
@atonyrodify
@atonyrodify 9 ай бұрын
Hello!I noticed you said you reuse a head gasket. Is it normal for atv head gaskets to be reused?
@FourwheelerDoctor
@FourwheelerDoctor 9 ай бұрын
Yes I usually spray the gasket with copper seal and reuse. I've only ever had a couple times at the gaskets were damaged and I didn't reuse them. Just guessing I've probably rebuilt about 500 ATVs and when I just do a overbore on the cylinder I will reuse the gaskets with copper seal and have had no issues.
@utahwanderlust700
@utahwanderlust700 Жыл бұрын
Did I miss it or did you check ring gaps off camera?
@FourwheelerDoctor
@FourwheelerDoctor Жыл бұрын
No I didn't check the ring gaps. These were not file to fit rings.
@johndragonman
@johndragonman 3 жыл бұрын
hey i have one of these.. 100 hours of use and the rear cylinder cam chain tensioner failed.. see that bit of metal the guide sits on just under the crank shaft at 9:44.. that snapped off on mine :( the engine i think over heated causing the tensioner to melt. the chain went slack, it threw it off the cam sprocket then wrapped around the crank. i am just trying to gauge if the engine is saveable. i really dont want to remove it from the UTV, and i really dont want to split the engine to replace the bit of metal thats snapped off. do you think it would still work OK without that bottom chain guide that is under the crank shaft chain sprocket? also sadly in the UK this engine has nowhere that sells parts for them so it all has to come from china :( what do you think?
@nou8476
@nou8476 3 жыл бұрын
in my own personal experience, take the engine out and split the case, these can am engines cant have any chunks in the oil, and youll need to replace all the parts that melted/broke unless you want to rebuild the whole engine when it spins a rod bearing or main bearing from junk in the oil
@lukekremer1413
@lukekremer1413 4 жыл бұрын
Im currently trying to time my engine after a rebuild right now as well and i noticed that when your timing cam #1 at 1:12:32 in the video, your timing lines on the cam sprocket are not perfectly horizontal with the jug. This is the same exact issue I am seeing with my 1000r engine, and only with #1 cylinder just like yours, cylinder #2 aligns horizontally perfect. How do you know that the timing marks should be rotated slightly counterclock wise rather than rotated slightly clockwise?
@FourwheelerDoctor
@FourwheelerDoctor 4 жыл бұрын
In the case with the front cam. I would normally shy toward the marks being shifted slightly forward so the when the tensioner is installed it would put pressure on the chain and and rotate the cam slightly counterclockwise.
@ignaciopina4099
@ignaciopina4099 3 жыл бұрын
Is there a way to change the through shaft without opening the case ?
@CristhianSilva-c3d
@CristhianSilva-c3d Жыл бұрын
Donde puedo conseguir repuesto del Rotax 1000 en ecuador
@jaywilliams052108
@jaywilliams052108 4 жыл бұрын
Wats the torque specs for the 8mm cover bolts?
@FourwheelerDoctor
@FourwheelerDoctor 4 жыл бұрын
The manual calls for 10 newton meters or 7.5 foot pounds.
@bballracer92
@bballracer92 4 жыл бұрын
"heard of that happening before" Bahaha
@FourwheelerDoctor
@FourwheelerDoctor 4 жыл бұрын
Once or twice
@luisconcha915
@luisconcha915 3 жыл бұрын
Hola.podria ser en castellano estaría bueno
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Lo siento, pero mi dialecto sur no se traduce muy bien al español
Can-Am Gen 1 crank case bearing sleeve removal and install
9:51
Mud Hawg Mafia
Рет қаралды 6 М.
Can Am Outlander Renegade 500 650 800 Motor Assembly Part 2
16:11
shanesoutty
Рет қаралды 179 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
1% vs 100% #beatbox #tiktok
01:10
BeatboxJCOP
Рет қаралды 67 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
Yarbo unboxing  new version snow blower step-by-step   4K
28:12
Michael and Maisam
Рет қаралды 4
Honda Rancher 350 Top End Rebuild
54:59
Four wheeler Doctor
Рет қаралды 22 М.
Can am 1000 Engine Disassembly
23:58
Four wheeler Doctor
Рет қаралды 9 М.
Most Expensive Mistakes on the Construction Site 2024 EP 7
21:24
BIG A.R Construction
Рет қаралды 195
Can Am Outlander Renegade 500 650 800 Motor Assembly
13:16
shanesoutty
Рет қаралды 126 М.
Can Am Renegade 940 Rebuild Case and Crankshaft
14:32
Nick Stockert
Рет қаралды 13 М.
Can am 1k transmission rebuild guide
16:27
CrazyQuads
Рет қаралды 53 М.
Can-Am Gen 1 Renegade/Outlander  975 Mr RPM big bore build, Part 3
13:57
Can-Am Mud Build: Part 2 - MrRPM
4:36
Dirt Trax TV
Рет қаралды 146 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН