Front Wheel Bearing / Hub Replace. 2013 V6 Dodge Charger SE.

Wheel Hub Assembly - amzn.to/2nzzIZP
Red Loctite 266 - amzn.to/2mg6PSe
Silver Antiseize - amzn.to/2mg69vT
Exam Gloves used in video - amzn.to/2mHdVLx
Breathable Work Gloves - amzn.to/2n1pHD1
Torque Wrench - amzn.to/2n9jzZS
Brake Cleaner - amzn.to/2nDFYfR
Jack Stand - amzn.to/2mWlcbb
How to install front wheel hub / bearing. 2013 Dodge Charger.
Amazon Affiliate Links used. This does not add costs to Amazon Products but helps me pay the bills.

[@mrficks1838]

*Materials Used:* Wheel Hub Assembly - amzn.to/2nzzIZP Red Loctite 266 - amzn.to/2mg6PSe Silver Antiseize - amzn.to/2mg69vT Exam Gloves used in video - amzn.to/2mHdVLx Breathable Work Gloves - amzn.to/2n1pHD1 Torque Wrench - amzn.to/2n9jzZS Brake Cleaner - amzn.to/2nDFYfR Jack Stand - amzn.to/2mWlcbb Amazon Affiliate Links used. This does not add costs to Amazon Products but helps me pay the bills.

[@clarencewatkins1634]

Thanks for sharing.

[@mrficks1838]

Thanks for the nice comment.

[@xxgoukenxx]

So I think one of my front hubs is out... I’m hearing some odd noise while driving. Which hub bearing would you recommend for a replacement? Also, I’ve seen ones with 3 mounting points along with ones with 4 mounting points. I haven’t gotten underneath my car yet to see which is correct. Front axl nuts or not. 2013 charger sxt plus. How should I quickly find out without taking everything off. Thanks to any for any insight.

[@mrficks1838]

xxgoukenxx • I pinned a comment with the materials I used. It's also in the description. That one i used (DuraGo) is still holding up fine. You likely have the same one.. Check by taking the wheel off and spinning the hub by hand and that will tell you if the sound is coming from it or the brakes. Also before you take the wheel off you can grab the tire on both sides and see if the wheel is wobbly if you push n pull on it..(should be stiff).

[@berniesigala2521]

The 3bolt mounting flange is for RWD and the 4 bolt flange is for AWD.

[@dennisandhisthoughts726]

Thanks for the video. You saved me $200.00

[@ammarhamood6445]

Hi thanks for the good explanation I got a question and it is really what get me over here to watch your video . what is the bar that goes up all the way at 7:23 which you point your fingers at ?? I know the assembling point is called bearing assembly but ,what is the the whole bar that the bearing is put on ?? Cuz I got my challenger 2012 R/T V8 crashed from left side and that bar got broke and im looking for this part nd cant find it .

[@mrficks1838]

Ammar Hamood • It's called the Knuckle. Thanks for watching Ammar.

[@ammarhamood6445]

Thnx for answering back , I searched all over amazon and ebay and was confused which one gonna fit on my challenger 2012 R/T V8 5.7 so I will ask for a favor ? if you know any automobile spare parts around and it is preferable if you know somebody directly , I will be very thankful.

[@mrficks1838]

Ammar Hamood • You looking for a knuckle or wheel hub for your challenger?

[@mrficks1838]

This is a front wheel hub that fits your V8 Challenger - amzn.to/2Dd4gbb

[@mrficks1838]

Here's the knuckle for your car too - amzn.to/2Dz6xeA

[@julianpasillas9675]

Is the repair applies to the v8 model as well?

[@mrficks1838]

Depends if you have RWD or an AWD model.

[@julianpasillas9675]

Is a RWD RT

[@mrficks1838]

@@julianpasillas9675 - Then yes, should be the same.

[@ramonbarraza3997]

Would this work on a 2011 Rallye Plus?

[@mrficks1838]

If it's RWD, yes.

[@treyyscott5655]

Is the rear axle nut the same size?

[@mrficks1838]

There is no axle nut on the front of mine (RWD). The rear axle nut is 35mm if I remember right.

[@2averagenoobs108]

Ay man, I read a review that the noise is worse when it was installed, seeing this video is 9 months ago, how has driving with this wheel bearing been so far? Any negatives? I need to replace mine :(

[@mrficks1838]

It's been over a year (March 2017) and no noise at all and drives great! Best wishes on your swap.

[@2averagenoobs108]

Mr Ficks Thanks man!

[@jackshahnazarian8243]

Hey @Mr Ficks, would you happen to have the rotor size somewhere? I'm doing work on a 2012 SE and can't tell what the correct OEM rotor size is.

[@mrficks1838]

Yes, I just bought one recently - amzn.to/3bZVvyC .

[@3.6pentastardude81]

12.6"

[@kingdavid4u1588]

How its done. 2010 Chrysler 300 Touring front hub Assembly bearing replacement video. kzbin.info/www/bejne/iXS4i5-Cjp1ssLc

[@mrficks1838]

Not the same car or front suspension even.

[@kingdavid4u1588]

Oppps sorry. Wrong video. Sorry

[@pauljoey7977]

Dude it could have been a 5 min video

[@mrficks1838]

Dude you could of been grateful for a free video.

[@3.6pentastardude81]

You recommended a Chinese part. Very cheap. Remember this is a MOPAR not a ricer

[@mrficks1838]

It's held up fine but I do agree to buy USA made. Please post a link to a good one you know of. Remember this is a place to be constructive, not just to whine.

[@mrficks1838]

The hub I have is listed to buy is from an American company but they do appear to manufacture overseas. - duragoparts.com/products/hub-assemblies/

[@darrengarcia4937]

MOPAR is owned by non-USA countries you dunce. If it works it works.