I love my Xbox too much to trust a shoestring to hold it.
@gamerboi23393 жыл бұрын
Same
@Yungchris7603 жыл бұрын
Its not for shitty xbox anyway buddy.
@streamyboys18333 жыл бұрын
@@Yungchris760 damn
@uttam_Jadhav3 жыл бұрын
@@Yungchris760 ooohhh
@HAMDANKHAN3 жыл бұрын
@@Yungchris760 😂
@NormSchmidt-pg9cs5 ай бұрын
Just did this for my daughter's ps4 and it works great thanks man
@user-reddevilutd3 күн бұрын
It's a good idea but maybe with something a little stronger than a shoelace, maybe brackets from a hardware store
@DaVillain063 жыл бұрын
Very creative and resourceful, I would do something that looks more secure though. Dont want my console falling off and then having to replace it
@francisohhh52694 жыл бұрын
Just did this method and it made my setup look way cleaner! I hid the extra length of the cables behind the ps4 since it's not flat on the wall
@FuzzyHat4 жыл бұрын
Good idea to hide the cables behind th PS4
@mrjasonrowland4 жыл бұрын
Thanks for the video. I just used this method with a PS4 slim and mounted it behind my TV on the right side or opposite side the OP mounted his. A few things to consider. One, the string can be tricky to size, particularly the shorter length string. The shorter one has to be PERFECTLY TAUGHT as the PS4 slim doesn’t have much to grab onto at the tops. Two, if mounting a PS4 slim on the right with the disc drive on the bottom, the string (if thin) doesn’t block the disc drive but the string does lay right over both the power button and the disc eject button. It does not interfere with either but does require one to be more careful when pushing those buttons. Three, all of the vents are pretty clear as long as you don’t use thick string. Four, I added tiny sticky furniture pads on top of the screws to avoid scratching the PS4 and to add a little more room between the wall and the bottom of the PS4 slim. Kind of over kill but I did it because my screws had pretty fat heads. Just cautionary and I had them around already. I also added a few of them where the bottom of the console rests against the wall. Five, the PS4 should be angled slightly to provide a little more room on the bottom for increased ventilation. Keep in mind this isn’t a big deal as the bottom of the PS4 has less room when just sitting on a shelf or dresser or the like anyway. Six, larger washers are better and will help prevent the string from sliding out around the rounded edges of the PS4. Seven, I added tape over the top of the washers and screws and screwed down the screws to prevent the string from popping out from around the edges of the washers. Again, overkill, but I already had the items and it gave me a little more security. I also added tape on top of the string where it touches the sides of the console not blocking anything. All of my string is black and the tape is black as well so it blends in. Besides, it’s behind a large, flat screen TV so nobody will see it anyway. All in all, it’s secure, was free, and it works well. Hope that helps.
@FuzzyHat4 жыл бұрын
I’m gonna pin this as it will answer a lot of questions people ask in comments!Thank you!!!
@origamikira2 жыл бұрын
thanks for the help, i used paracord string and mounted it on a concrete wall using a slightly different method but thanks for the dimensions anyway
@FuzzyHat2 жыл бұрын
Thanks, I’m glad I was able to help!
@Mzuch144 жыл бұрын
I have trust issues watching this video
@FuzzyHat4 жыл бұрын
Ha ha
@kev-mrsound08185 жыл бұрын
Nice one going to give this a shot” get my PS4 Vr this week 👌🏽 days of play from PlayStation are doing great deals this week” VR headset and camera €200
@FuzzyHat5 жыл бұрын
That’s a good deal on VR.!
@rockybeneboa2 ай бұрын
Great DIY, thanks
@tonez_8317 Жыл бұрын
I’ve done 2 already amazing
@FuzzyHat Жыл бұрын
👍
@boneswtff3 жыл бұрын
not going to lie but that’s hella smart and a good idea
@FuzzyHat3 жыл бұрын
Thanks!
@nilomo_68784 жыл бұрын
What are the Mesurements in cm for the Ps4 Mount?
@Chandan-vb8pq Жыл бұрын
Thanks....
@omarhuerta54773 жыл бұрын
This literally is a real cool hack smart thinking 💯
@FuzzyHat3 жыл бұрын
Thanks.
@JoseAlvarez-if8tt4 жыл бұрын
This also worked out for my PS4 Pro and since it has 2 indents unlike the regular PS4 the vents aren’t covered but for the top string I would add 2 inches more, I added only 1 and it was kind of tight for to reach the second indent, all in all looks good, works great and its free
@FuzzyHat4 жыл бұрын
That’s awesome you were able to do it for PS4 pro!
@DarkJedireaper3 жыл бұрын
And then one day it falls off the wall lol
@CoroaEntertainment4 жыл бұрын
Personally, I would have positioned the PS4 behind the TV to completely hide it from view. Btw 4:04, you should get a 90 degree USB extension cable so the the wire is tucked in nice and close o the console. :-)
@elnewbie26114 жыл бұрын
That wall mount isn't good for the ps4, it covers the ventilation of ps4, not recommended
@FuzzyHat4 жыл бұрын
Read the comment I pinned, from one of the viewers that actually did this.
@CRWM3N14 жыл бұрын
Actually the vent is on the sides of the ps4 not on its flat surface 🙄
@sayeedabdullah584 жыл бұрын
@@CRWM3N1 well one whole side is covered by the lace. And besides, shouldn't the heat of the exhaust melt the lace? You know, at least to some extent?
@mrluxurious50314 жыл бұрын
@@sayeedabdullah58 shoe string doesn't melt first of all, and as much as it may get heated, it should never tear, so long as there's no fire atleast. But thats not likely to happen.
@silentsoul864 жыл бұрын
It sits far enough off the wall that over heating doesnt happen. Ive had mine up for almost a year and no issues. Dont knock it til you rock it. 5$ vs the 30$ kit and both work the same.
@tylerroycroft49902 жыл бұрын
If your going for this idea please put plugs into the plasterboard and a drop of CA glue on the notts for some peace of mind😁
@aweirdsimon65544 жыл бұрын
perfect if you want a blod
@powkiegaming26164 жыл бұрын
Now thats cheap. Good video.
@FuzzyHat4 жыл бұрын
Thanks
@yasmaniflores51885 жыл бұрын
Awesome!!! Thanks for this video man!
@FuzzyHat5 жыл бұрын
I’m glad you liked it!
@chriswhitfield15 жыл бұрын
Good idea! It’s 9” for the two screws but what’s the measure across and down for the third?
@FuzzyHat5 жыл бұрын
It’s 1 inch. Sorry, the screw was so close, there wasn’t enough space to put that measurement when editing, without making it the number super small.
@chriswhitfield15 жыл бұрын
Fuzzy Hat thanks. I’ll give it a go 👍🏻
@FuzzyHat5 жыл бұрын
I’m glad I could help.
@chriswhitfield15 жыл бұрын
Fuzzy Hat it works a treat and cost absolutely nothing bar a pair of laces - looks great. Thanks for your help
@Mink20103 жыл бұрын
Whats the function of the third anyway ? I mean, you can mount it just the same with only the two upper screws, just shorten the straps a bit.
@manirashme14063 жыл бұрын
nice .very good
@FuzzyHat3 жыл бұрын
Thanks!
@myracarbajal49782 жыл бұрын
Thank you!!
@8405mikey3 жыл бұрын
Whats the distance for the middle screw. I saw the top was 9inch.
@FuzzyHat3 жыл бұрын
Right in the middle and 1 inch up.
@raoshab7520 Жыл бұрын
Great
@Andikiwiify5 жыл бұрын
Hey mate, nice video. any idea on the string lengths for a PS4 PRO? if no, how do you go about measuring them? is it just trial and error with the knot ties? cheers
@FuzzyHat5 жыл бұрын
Thanks! I really don’t know the measurements for PS4 pro, but I would think it should be pretty close. I would just take the string of your choice and cut it a bit longer and try it, and just make it shorter as need.
@Andikiwiify5 жыл бұрын
Thanks bro. Got it done.
@locorocohui4 жыл бұрын
@@Andikiwiify hey AJ, what measurements did you use? also got a ps4 pro to hang...
@Andikiwiify4 жыл бұрын
@@locorocohui Hey mate, I just winged it. i did the lower sting first, took a guess really, then the top string I just wrapped it around while it was sitting in the lower string, the longer it is, the further away from the wall the ps4 will sit. little space is good i think so it doesnt over heat.
@Andikiwiify4 жыл бұрын
@@locorocohui Ive measured it. Approx, 91cm for the lower sting and 73cm for the higher one.
@roadglassandmore90645 жыл бұрын
Sweet!
@87chevylisto425 жыл бұрын
Road and more 💪🏼😂🧐
@FuzzyHat5 жыл бұрын
You know it!
@kingmasonry3 жыл бұрын
Can you do one for ps5 now please. That would def go viral right now
@FuzzyHat3 жыл бұрын
I will as soon as i get PS5
@salvadorrivera74913 жыл бұрын
I did this and used 2 strips of velcro with adhesive and it's been up for over a month
@FuzzyHat3 жыл бұрын
Nice!
@xavierleon78494 жыл бұрын
Thanks for this video !!
@FuzzyHat4 жыл бұрын
You are welcome!
@CarlosLopez-fb4sq2 жыл бұрын
It’s cool but the wires make look like a mess
@Uruapan165 жыл бұрын
Awesome
@FuzzyHat5 жыл бұрын
Thanks!
@taylorbond41723 жыл бұрын
This needs to have anchors for that dry wall if you are not hitting studs.
@FuzzyHat3 жыл бұрын
Yep, I agree, this was just for a video denomination., although it’s been over a year and my PS4 still holding on the wall .
@RonaldCiubuc4 жыл бұрын
Genius
@stbaldawi3 жыл бұрын
what is the name of the screws you screwed on the wall ? or a link where to buy them
@FuzzyHat3 жыл бұрын
They are just regular screwed I bought at local hardware store, I think they are 1” or 1 1/4 “ long
@AlbMen_1172 жыл бұрын
How’s it hold up??
@belalbamin7385 жыл бұрын
is it also possible to hang the ps4 the other way around.. cables heading downwards ..and if so what are the measurements .. By the way appreciate your video a lott.. thanxx
@FuzzyHat5 жыл бұрын
Probably possible, I have not tryed it. But before you do that, test it first make sure it works in that position. Measurements are in the video, and should be the same no matter which way you hand PS4, 40 inches, 27 inches and 18 inches for the controller. But I was using shoe laces and they are a little stretchy so go about half inch bigger if you are using thick string that is not stretchy and if using something thin just stick with original measurements. I hope this helps!
@mrjasonrowland4 жыл бұрын
Yes. I did it with a PS4 Slim. Works well as long as the string isn’t too thick as the string will rest on the top of both the power and disc eject buttons and may block the disc drive if thick enough. The measurements are roughly the same BUT will vary slightly depending on how elastic the string is. I think the hardest part is getting the correct length on the string. I had to tie and untie mine several times to get it just right. Particularly the shorter length. That one has to be perfectly taught.
@coryline3 жыл бұрын
@@FuzzyHat hello. Trying to do this with a ps5. How did you come to those measurements?
@MiguelMartinez-rx4rt4 жыл бұрын
Thanks Genius.
@amrkoptan40413 жыл бұрын
neat !!
@FuzzyHat3 жыл бұрын
Thanks!
@urosskulj804 жыл бұрын
Thank you!
@FuzzyHat4 жыл бұрын
You are welcome!
@active.losinj3 жыл бұрын
Uroš si probao sistem, jel vrijedi probati?
@Namgyel3 жыл бұрын
@@active.losinj Žal ne, sem potem drugače naredil. TI si poskusil?
@CyberPunk-pe4vk4 жыл бұрын
Nice and simple but it sounds like scary. What if earthquake hits you up.
@FuzzyHat4 жыл бұрын
If earthquake hits , PS3 would be the least of my worries! And Im sure this set up will hold the PS4 on the wall.
@totallynotsleepy58754 жыл бұрын
Fuzzy Hat that is if the wall is still there
@aamir1913 Жыл бұрын
Thanks for this awesome tips .. on Wall screw you have 9” but What about the middle screw How much Down is it compare to the two line up 9 inch!! Thanks 🙏
@FuzzyHat Жыл бұрын
Middle is in the middle and down 1”
@aamir1913 Жыл бұрын
Thanks mate
@aamir1913 Жыл бұрын
Can you write exactly inch in cm Thanks
@roofrat682 жыл бұрын
So what size would it be for a ps3? And the one the video, is it for the ps4 slim?
@fvue76634 жыл бұрын
Use toggle bolts, not all dry walls are equal.
@FuzzyHat4 жыл бұрын
Very good idea!
@enriqueayala87554 жыл бұрын
Do I just place the screws wherever I'd like them to be?
@FuzzyHat4 жыл бұрын
9 inches apart two top screws and 1 inch down in the middle for lower third screw. I think I put the measurement in the video too.
@rubenpenaz6415 жыл бұрын
What size did you use for the PS4 controller
@FuzzyHat5 жыл бұрын
18 inch
@josiahechols726010 ай бұрын
What type of screws do you use??
@FuzzyHat10 ай бұрын
Just regular wood screws.
@marianatejeda8125 жыл бұрын
what if comes an earthquake :o
@FuzzyHat5 жыл бұрын
In case of earthquakes PS4 is the last thing I would worry about, and I would think this wall mount still hold the pa4 on the wall.
@iamidrac4 жыл бұрын
@@FuzzyHat right
@silentsoul864 жыл бұрын
What if the moon falls and hits you in the @ss? In an earth quake the ps4 would be the least of my worries
@cbkzokii55684 жыл бұрын
if there is and earthquake i’m pretty sure the ps4 is falling no matter what
@404Toni4 жыл бұрын
🔥🔥🔥🔥🔥🔥
@illtubethat8 ай бұрын
talk about a shoe-string budget...
@FuzzyHat7 ай бұрын
😂
@Sofire1003 жыл бұрын
You are awesome sauce😁!!!!! Thank you for this!!!!
@FuzzyHat3 жыл бұрын
Glad you like it!
@stbaldawi3 жыл бұрын
what are the shoe laces lengths that first used on the wall ? Beginning of video u cut 3 lengths of shoe laces, u used two of them on the wall, but the video didn't mention which shoe laces are they
@FuzzyHat3 жыл бұрын
40, 27 and 18 inches, it shows measurements in the video.
@stbaldawi3 жыл бұрын
@@FuzzyHat which ones of those lengths did u put on the wall for the console?
@FuzzyHat3 жыл бұрын
40 and 27 on the console,18 for the controller, but length will depend on the string you use, like if it’s stretchy or not
@MrTristanbryce3 жыл бұрын
I followed it step by set and the Measurements are way off
@FuzzyHat3 жыл бұрын
The shoe laces I used were kinda stretchy, so maybe that’s why the measurements off?
@the_trevinator_4 жыл бұрын
Should use dry wall plugs why you not use them
@FuzzyHat4 жыл бұрын
Yes , plugs will make it more secure. I didn’t use the plugs because I was thinking about making another mount ( video) and didn’t want big holes left in drywall. But never got around to making it and just left PS4 as is and it’s still hanging on the wall no problem.
@stevensanchez77403 жыл бұрын
bruuuuuuuuhh, i got tooo much anxiety for dat
@FuzzyHat3 жыл бұрын
Lol, it’s fine, mine PS4 been hanging on the wall for a long time now without any issues.
@acuaknigth28924 жыл бұрын
🤯 DAMN THIS I WAS MUCH HARD BE ME SELF AND I DIDN'T USE SHOES STRING I USE THE DOLLAR TREE AND IT WAS SUPER HARD BECAUSE IS NOT ELASTIC
@Le_Papa3 жыл бұрын
Imagine sleeping at 4am and ur ps4 just falls
@FuzzyHat3 жыл бұрын
So far it has not fallen off , almost 2 years now..
@Le_Papa3 жыл бұрын
@@FuzzyHat dam
@ferdinandtabago85333 жыл бұрын
is the shoe lace the same length that will be used for the ps4 pro?
@FuzzyHat3 жыл бұрын
I’m not sure about the size for the pro, I know someone left a comment on here with ps slim measurements
@guillermomendoza12374 жыл бұрын
Which two size laces did you use for the ps4 not the controller
@FuzzyHat4 жыл бұрын
18” inches .
@melannieworld4 жыл бұрын
Can you do this to laptop too?
@FuzzyHat4 жыл бұрын
Laptop?, I never thought someone would want to hang laptop on the wall next to a 📺, but it’s possible I guess.
@htcthunderbolt3 жыл бұрын
no drywall anchors at least?
@FuzzyHat3 жыл бұрын
It was for demonstration only, but it is a good idea to use anchors.
@carllbryanpaa27583 жыл бұрын
What is the length of the string for the console. Thank you man
@FuzzyHat3 жыл бұрын
27 and 40 inches
@carllbryanpaa27583 жыл бұрын
@@FuzzyHat thanks man
@jezhvrod40284 жыл бұрын
Not how I would do it but it's cool tho😁 also that's a NICE customized PS👍🏼
@FuzzyHat4 жыл бұрын
Thanks!
@TamNguyen8112 жыл бұрын
what's the length do you recommend for thr ps3?
@FuzzyHat2 жыл бұрын
I’m not sure, I only made one for my PS4.
@Uneke5 жыл бұрын
Would you use the same dimensions for a slim?
@FuzzyHat5 жыл бұрын
I think the top string would need to be shorter.
@Uneke5 жыл бұрын
Thanks for the fast reply. I’ll cut it at the lengths and measure the top before tying.
@Uneke5 жыл бұрын
232 I ended up taking 1/4” off and was a little saggy, so I took 1/2” and it was nice and snug
@supersaiyandavid5553 жыл бұрын
Fuc### that cool but you need to hide wires not to show
@iang33433 жыл бұрын
Stole the design from the company FloatingGrip but it’s cheaper and it still works so more power to you
@FuzzyHat3 жыл бұрын
Thanks! You should read the comment that company ( floating grip) left a while ago here , they were pretty mad lol.
@Ellasarr4 жыл бұрын
What was the length of string for controller?
@FuzzyHat4 жыл бұрын
18 inches
@grlthing5 жыл бұрын
nice!! :)
@CreepyUncleIdjit4 жыл бұрын
What kind of measurements do you recommend for the PS4 Pro?
@FuzzyHat4 жыл бұрын
I would try same size strings as in the video first, and then make adjustments if it doesn’t work!
@syamellasyraf323 жыл бұрын
What is the title of the song?
@hamdankhan90063 жыл бұрын
i am fit my ps4 slim it is not dangeriosy please give me ans
@FuzzyHat3 жыл бұрын
Yes you can , people have done it , but strings have to be a bit shorter, look through comments!
@tanjoli1472 Жыл бұрын
Please give us lengh in "cm"
@FuzzyHat Жыл бұрын
You can convert it from inches to cm online. I know I should have put measurements in cm too, just didn’t think of it when I was making a video
@sgsuper11503 жыл бұрын
Blowing hot air from the ps4 onto TV is not a good idea
@adambills28364 жыл бұрын
You block the side vents with this method
@FuzzyHat4 жыл бұрын
Please explain how small string blocked the vents?
@990mark9904 жыл бұрын
@@FuzzyHat the string is pulled tight over the vents. Holds heat in....what needs to be explained
@jastyle5214 жыл бұрын
@@990mark990 you are soooooo right. Has anybody ever looked at their side vents to clean all of the dust and hair out if it. It's definitely pulling in lots of air on the side. That baby is going to run hot and loud!!
@990mark9904 жыл бұрын
@@jastyle521 and maybe the way it hangs the string will sit in a position that it isnt really blocking it, I'm not sure. That's just my impression on my initial look. Definitely something to consider.
@mrjasonrowland4 жыл бұрын
I used very strong but also very thin string and the side vents are not blocked at all. No over heating issues whatsoever. Now if one uses thick shoe laces then they will have issues.
@Keizos01024 жыл бұрын
Just a question wouldnt the ps4 overheat? Would love a response
@FuzzyHat4 жыл бұрын
To this day no issues with overheating, a lot of people have this set up now and no problems!
I realized that he put the shoe laces on the air holes so it's blocking every single Air hole on the PlayStation so the damn thing is going to overheat.
@FuzzyHat3 жыл бұрын
It’s not blocking any vents, by the way. Look closely!
@baptista55783 жыл бұрын
Obstruction the vents? I don't think thats a good idea.
@shehoopn50164 жыл бұрын
If it falls
@FuzzyHat4 жыл бұрын
Has not fallen yet.
@BackWoodsRDNK2 жыл бұрын
Yeah no ? That’s not safe !!
@itsKhaleeque3 жыл бұрын
It's risky
@stefanoserrani51603 жыл бұрын
Pensa se ti cade la play che botto ahahah
@sayeedabdullah584 жыл бұрын
Is it safe?
@FuzzyHat4 жыл бұрын
Absolutely!
@sayeedabdullah584 жыл бұрын
@@FuzzyHat I don't think I'll ever get over the anxiety of watching my ps4 hanging like that
@roberttorkoy92904 жыл бұрын
Na ezért ujjlenyomatos a lemez!
@idkhowtonamethischannel.3 жыл бұрын
trust issue level is rising up
@FuzzyHat3 жыл бұрын
Lol
@reyzuna4 жыл бұрын
good, you have disabled the air flow of both sides of your PS4 with that shoelace that will make it now prone to overheat.
@mrjasonrowland4 жыл бұрын
I assumed the same until I tried it and it does not block the vents at all unless the shoe string is really thick. I chose to use really strong but thin string. There is also a company that uses this same method and has sold thousands of these mounts with no issues. Their string is close to the thickness of his shoe laces used in this video. Be well.
@thebakeddonut20383 жыл бұрын
I think your idea was stolen bro lol, this chick who owns this company called air mount or something has the exact same design and charging people waaaaay more than what you could make at him as shown here
@FuzzyHat3 жыл бұрын
Yeah, I seen that.
@oSIXO.3 жыл бұрын
😳
@starmarker77514 жыл бұрын
I'm not that poor actually
@maxklassen2544 жыл бұрын
Do you have an SSD in your PS4 Pro then?
@starmarker77514 жыл бұрын
@@maxklassen254 it got nothing to do with being poor ma man 😂
@Horrordelic4 жыл бұрын
What do this got do with poor ? Its a nice solution to wall mount the ps4 ..
@yasminmehmood28924 жыл бұрын
I'd rather buy a proper mount
@justin34414 жыл бұрын
Yeah.. no
@VambSnake4 жыл бұрын
Don’t try that cuz you will close all the air intake opening and Playstation will choke lead to over heating. Easy way but so stupid
@FuzzyHat4 жыл бұрын
Please explain how small string that wraps around corners of PS4 console will close the air vents ?
@cvrsssd5 жыл бұрын
*bunnyhop.exe*
@Roger-ob2ft4 жыл бұрын
This is really sad..
@FuzzyHat4 жыл бұрын
Sad why? Because I ruined perfectly good shoelaces? Lol