Fixing A Sprinkler Valve "Quick Fix," No Glue

[@akhtarparvez9446]

Excellent video and advice how to replace a faulty irrigation valve. Thank you, it was easy and economical to fix my irrigation valve.

[@garyssprinklerrepair]

@@akhtarparvez9446 thank you, hope you remembered to Subscribe to my Channel for more great content help.👍

[@shastastan1935]

Thanks, Gary. I used your tip a year ago and watched this again today because I have another fix to do now. This is oh so much easier than re-doing the manifold.

[@garyssprinklerrepair]

I agree, glad you’re still subscribed to our channel so you know where to get your info. 👍

[@shastastan1935]

@@garyssprinklerrepair Bought and installed the valve today from Ace. It was $30! Easy peasy!

[@shastastan1935]

@@garyssprinklerrepair Had to replace another one today. Watched again to make sure I did it right. Hey, I'm an old guy with CRS (Can't Remember Sh_t).

[@thomasmcclure3359]

Great video, Gary. I followed your procedure three times with a no luck. I decided to go one step further and replace the solenoid valve since I had purchased it with the new valve. Problem solved! I guessing the solenoid had sand inside which did not allow it to seal. Hope this helps another rookie!

[@jasonjackson4555]

Man, this is EXACTLY what I was looking for! I have the exact same sprinkler setup that I installed by myself a few years ago. It’s been leaking for over a month so I had to shut it off. I was dreading having to dig another hole and replace everything. This will be my weekend project! Thanks!!!

[@garyssprinklerrepair]

Glad to hear it, enjoy your weekend. Glad it helped you, don’t forget to Subscribe to our Channel it helps us grow.

[@minebudiman3586]

This was so amazing.... You saved my day!!! I was dreading the valve replacement for weeks... finally one last one broke and I had to deal with it. If I knew this was so easy, I would have done it weeks ago. YOU ARE MY HERO!!!! THANK YOU THANK YOU THANK YOU!!!!

[@garyssprinklerrepair]

Mine, glad you overcame your fear and found that you’re fully capable of handling this project on your own. Don’t forget to Subscribe to our Channel it really helps us grow ✌️

[@initiativeplaytherapy88]

Thank you for this video. Not only did you save me from having to cut off all my valves, you made some comments about debris in the system that helped me understand why my system needed some maintenance in the first place.

[@MrNewgard]

This is golden! Thank you, Sir! Now I can easily fix my leaky valve without cutting the pipes!

[@garyssprinklerrepair]

MrNewgard you’re more than welcome. If you liked the video be sure to Subscribe to our Channel it’s free and we have many other helpful videos. ✌️

[@ronbolena9609]

Fantastic video Gary, you just saved me a ton of extra work trying to replace the whole valve. Thank you!!

[@garyssprinklerrepair]

Glad you found the video useful. Feel feel to bookmark our Channel by Subscribing and tapping the bell to be notified when we answer any of your questions or post new content.✌️

[@garyssprinklerrepair]

Happy it was useful for ya, hope you didn’t forget to Subscribe to our Channel for more video tips.✌️

[@splibb]

Man, what I would give to have my valves standing up in the air like this and not in an arm pit deep, black widow infested mud hole! That said, I really appreciate your videos! I forgot if the spring went up or down, and you answered that!

[@garyssprinklerrepair]

splibb you could always cut them and 90 the pipes up. Subscribe if you get a chance and tap notifications it really helps the Channel with placement. PS you’re comment was hella funny, same thing I think when someone wants me to work on one.

[@splibb]

Gary's Sprinkler Repair Done and done my friend!

[@I_Want_To_Know]

Thank you for being a great person and showing people how to do this! Most people nowadays are so greedy. You saved me so much money and I’m grateful!! 🙏🏼💖

[@garyssprinklerrepair]

Jenny, thank you glad to be able to help you out. Hope you got a chance to Subscribe to our Channel it helps us with standing on KZbin✌️

[@flyingv7747]

Thank you for taking the time to do this. I am a GC but seldom work on sprinklers. Today I am going on a service call for a leaking sprinkler valve and this really helped.

[@garyssprinklerrepair]

Flying V thanks, hope this did actually help. If ya get a chance to subscribe it would help me out too. I have 23 other videos. Gary

[@eggheadedmousy]

OMG, this is so inspiring! I should definitely reconfigure my tenant's sprinkler valve system with this master switch too

[@garyssprinklerrepair]

Good luck to ya, make sure to Subscribe to my channel in case you have a question or 2.👍

[@DanielBobke]

Glad I found this...I was thinking the same way - just replace the top parts of the valve rather than cutting pipe and having to glue things together again. I didn't even think about reusing the solenoid! Great tips...I know what I am doing this weekend.

[@garyssprinklerrepair]

Thanks Daniel, good luck on your repair. Don’t forget to turn the water off 1st. 😁 Hope you took a Minute to Subscribe to our Channel, it really helps the channel grow on YT

[@DanielBobke]

@@garyssprinklerrepair So here is one wrinkle...Rain Bird hasn't made the valves I have since 2008 (APAS 075). You can't find them very easily...found one on eBay for $45! I grabbed it quick!

[@DavQuan]

This video was so insightful. I couldn't not find any resource information on the Rainbird site. Thank you for making this video! Based on the views and comments, it has helped a LOT of people.

[@garyssprinklerrepair]

Wow, thank you for the amazing comment. Really glad it helped you out. Hope you remembered to Subscribe to our Channel for future assistance. 👍

[@Ioang40]

Basically ,replacing the guts of the valve and the solenoid. Smart and fast. Done it the same way every time.Great video!

[@garyssprinklerrepair]

Thx for the great comment Loan. Glad you are keeping it simple. Hope you had a chance to Subscribe to my Channel during your stay here✌️

[@stuntdriver2147]

Great video - I need to replace 4 Lawn Genie valves - am going to use this same method - not having to cut, glue and risk a leak is a huge PLUS ! Thanks so much for posting this.

[@garyssprinklerrepair]

Stunt Driver, glad I could help you out. If you get a chance feel free to Subscribe to my Channel as I have 40 other sprinkler videos. Also, let me know if you have any questions along the way.😎

[@ErikBartlow]

Great video! You saved me hundreds. I never thought to just replace the top part and leave the plumbed parts intact. Thanks again!

[@garyssprinklerrepair]

Saving people helping people save money was the reason I started my Channel. Hope you took a minute to Subscribe to our channel so you don’t miss out when new contents added.✌️

[@benzo13]

I got a leaky breaker lid and this video just soothed my worst fears! I don't have to take the whole valve off!! I have also heard that what you term a "breaker lid" may also be called a "plunger cap" or just "valve cap", any-whooo...Thanks for the vid very helpful!!

[@edwardhernandez2887]

Thank you Gary! I thought I was going to have to replace the whole valve! This is so much easier

[@garyssprinklerrepair]

Hope it worked out for you my friend, glad to be of help. Don’t forget to Subscribe to our Channel if you get a chance.😉

[@shastastan1935]

Hi Gary. I'm going to do another valve replacement today. Yeah, I watched your vid again too. Many thanks!

[@garyssprinklerrepair]

Great to hear, you’ll be a pro in no time.👍

[@mariecagle420]

Thank you! Very helpful. I was going to replace the entire valve. You just saved me alot of extra work.

[@garyssprinklerrepair]

You’re welcome, hope you took a minute to Subscribe to our Channel. It helps us on KZbin.✌️

[@natusfreedom472]

Saved me a lot of time & money .. my stupid sprinklers always giving me problems , diaphragm is always bad & sprinkler won’t turn off ..

[@garyssprinklerrepair]

Glad you found it useful, ya when it gets hot they seem to go out just like house AC. 😁Hope you remembered to Subscribe to our Channel.

[@jangseo1812]

Thanks, Gary. Your video inspired me and fixed my old head aching valve. Very helpful video. Cheers!

[@garyssprinklerrepair]

Always awesome to hear a feel good story. Glad everything worked out for you. Hope you took a minute to Subscribe to our Channel for more help in the future.👍

[@PedroMorenojr]

I just bought some replacement parts at Lowe’s. Followed this video. Thank you for the tutorial!!

[@garyssprinklerrepair]

Great news for everyone, glad you found the video helpful my friend. ✌️

[@jeffraia7068]

Thank You. Best video ever. Spot on perfect information and after watching the video I fixed the leak in 5 minutes with only a screwdriver. THANK YOU!

[@jeffraia7068]

By the way, the warning about the shut off valve not working was like a psychic prediction.... The ball valve did not work at all and when I checked it like you said to the water was still on. I simply turned the water to the house off and I was good to go, and I did not take a shower and turn my work area into a mud pit. Great video man, pro tips from start to finish.

[@garyssprinklerrepair]

Huge thank you, hope you took a minute to Subscribe to our Channel.👊

[@rubenharo4079]

Thank you very much for posting this video. I have the same system at home. Followed your steps to disassemble the valve, checked and cleaned gaskets and a filter and problem was solved! You saved me money by not calling gc. Thank you!

[@garyssprinklerrepair]

Ruben Haro you’re welcome, easy as 1,2,3 right? Glad it helped you out. If you get a chance be sure to Subscribe and tap notifications to help the channel grow. Also we do monthly Giveaways

[@شرمندهپنجاهوهفتی]

Gary, thank you for this great video, it was very helpful and mad my life easy🙌🙏

[@garyssprinklerrepair]

Glad to help you out. We add more content all the time. So, don’t forget to Subscribe to our Channel it’s really helpful to us as well. ✌️

[@44jmdom]

You da man Gary! Wish I saw your video a month ago, would have saved me some time! Have a blessed one Amigo!

[@garyssprinklerrepair]

Thx for the great comment. Glad you finally found us though. So, don’t forget to Subscribe.😎

[@RXDJ]

Thank you Gary, this was a very nice video that made a complicated and expensive home repair job simple. Very useful.

[@junecheverria4746]

Thank you Gary! Your instructions was very helpful. Made my work and pocket easier!

[@garyssprinklerrepair]

Always happy to help out, don’t forget to Subscribe to our Channel we have a lot of other content you might like.✌️

[@kennethchristie5167]

Thanks Gary! That was very helpful.

[@erinlanderson2040]

so helpful. with any luck this will fix our pressure after fixing the hole

[@garyssprinklerrepair]

Thanks for your nice comment, I too hope it helps you out. Hope you took a minute to Subscribe to our Channel to save us, for your next job.

[@amywang4442]

Thank you so much! I have the exact valve which just won't stop hissing at us. The valve is leaking. So I was deciding whether to replace the parts here and there, but I decided to do the exact thing you've taught me. Thank you...

[@garyssprinklerrepair]

Glad to be of assistance, hope you took a minute to Subscribe to our Channel. It really helps our Channel grow.👏

[@locohuero]

Thank you for a simple step-by-step walkthrough. Saved me so much headache.

[@garyssprinklerrepair]

You’re welcome LocoHuero A.G., glad you found our video useful. Be sure to Subscribe to our Channel to save for future projects.✌️

[@mnemonth]

Too obvious...heheh. So obvious that I never would have thought of it, myself. Thanks, man. You saved me hours of frustration. It worked for an old Lawn Genie valve. Fortunately, they don't seem to have changed the design in a couple decades and replacement was straightforward.

[@garyssprinklerrepair]

Always glad to help save the day. Hope you remembered to Subscribe to my channel it helps us in KZbin standings.👍

[@mnemonth]

@@garyssprinklerrepair @tppbila2155 0 seconds ago @garyssprinklerrepair Yup...liked and subscribed. I want back all the months of life I've wasted over the last twenty-four years keeping alive the kludged sprinkler system the previous owner put in this place. The stories I could tell...

[@dianecutsforth9363]

This saved me $225 for a service call and a ton of time and frustration!! $31 for 2 valves from landscape supply and my system was back in business!!

[@garyssprinklerrepair]

Glad to be of assistance Diane, hope you didn’t forget to Subscribe to our Channel. It really helps us on KZbin ✌️

[@outsider9288]

Solenoids go bad often, it's better to change it out with the new one, its only 2 wires to cut and reconnect! Great video, thx.

[@garyssprinklerrepair]

I agree, but you would be shocked how many people tell me they don’t mind doing plumbing but anything electrical…no way.

[@davidhernandez1739]

Perfect! Just what I needed. The valve was loose when I replaced it.

[@garyssprinklerrepair]

Great news , glad everything worked out. Just a heads up if the screws come loose again your water pressure might be too high. We have more info on our KZbin Channel. Subscribe for more content. Thank for the awesome comment btw.👍

[@bubbafungi]

Awesome information. Thanks so much. Saved me time and money. Much appreciated.

[@garyssprinklerrepair]

So glad to help you out. Be sure to Subscribe when you get a chance and tap that notifications bell to be notified when I upload new videos.✌️

[@donnaleiber6214]

Wonderful video! Very helpful, thorough, and useful. You helped two senior citizens (female at that) replace and troubleshoot a valve and save the hassle of explaining the symptoms to an English-speaking-challenged gardener and have to pay for a full valve replacement that wasn't necessary. Just out of curiosity, though, the bleed screw from the old valve blew out and we couldn't thread it back. (...which is why we replaced the top parts of the valve.) It did not appear to be stripped, nor did the threads of where it went. However, it already had teflon plumber's tape on it, which makes us think it had come out before and someone put it back. Two questions: 1. Would a new part from the factory have teflon tape on it already? 2. If a bleeder screw shoots out, can it be put back? It doesn't matter now since we replaced the top parts of the valve as explained in your brilliant video, but we are curious. The new valve's instructions make it a point to emphasize only to turn a bleeder screw one turn, suggesting it shouldn't be turned more or it might come out and not go back. Thanks so much for your video and help.

[@eiknarfzepol]

Hi there I hope I could answer your questions. 1. It does not come with Teflon tape from factory. The reason why they put Teflon tape is at one point the plastic threads were not holding it in place. 2. In my experience these are $25 plastic valves. Absolutely nothing wrong with plastic in fact I like them better than the metal one's.. especially for residential use. But that small knob in particular is very sensitive.... Hope that helps..

[@donnaleiber6214]

@@eiknarfzepol Thank you for your reply. What you said is nice to know.

[@garyssprinklerrepair]

Sorry I never saw your comment, sometimes KZbin screens my comments. As Francisco mentioned the valves don’t come with Teflon tape, they’re easy to cross thread if unscrewed to far. Swapping the valves top definitely fixed the issue.✌️ thx Francisco

[@donnaleiber6214]

@@garyssprinklerrepair No worries. Your video was very helpful! Thanks again!

[@dldennis5]

What's a bleeder screw? I too am a woman with no experience.

[@dkw4par]

You saved me a lot of headaches. Thank you ;)

[@garyssprinklerrepair]

Glad to be of assistance, hope you enjoyed it enough to Subscribe to our channel.✌️

[@GaryJeff-jy9vb]

Well done Gary!

[@garyssprinklerrepair]

Thank you, glad you found it useful. Hope you remembered to Subscribe to our Channel for more videos.

[@paulfraley]

Very good video Gary. Thank you from Texas.

[@garyssprinklerrepair]

More than welcome, hope you took a minute to Subscribe to our Channel it really helps us too.✌️

[@ajshah2748]

Thank you. Very helpful and to the point.

[@garyssprinklerrepair]

@@ajshah2748 You’re welcome, don’t forget to take a minute to Subscribe to our Channel✌️

[@TOM3684]

Great Video! Funny, I came to this same conclusion when my existing valves had been changed many times and there was no more room to cut the pvc manifold as it had every inch filled with slip/slip connectors. I had three brand new valves, so I did the same thing you did in the video. I also attempted to get a diaphragm rebuild kit first, but got the wrong ones. Nothing was bad with the valve bodies. I love this method! And the fact you are using a commercial grade valves....much better! Hey, I have three zones and two work ok, but the third has really low pressure and I cannot figure out why. Two of the three are at a 4 foot elevation above the valves in an upper yard. I have started removing heads to flush them to see if they are clogged, but so far the two of the heads flush clear and water runs slowly out of the body. My next test will be to put a pressure gauge on the hose bib right next to the sprinkler valves, but I suspect since 2 of 3 have pressure it wont be a inlet pressure issue. Why would 2 of 3 heads flow ok and the one not flow well? Thanks for your video, it is a great idea

[@garyssprinklerrepair]

Many things can cause the issue with low flow. If the other two zones have the same amount of sprinklers and operate great, then first thing I would look for is a cracked pipe. Turn all of the sprinkler heads off on the set with low flow, then turn it on and let it run for a few minutes. Next, walk around and look for a really wet area, there’s your crack. Let me know how it goes.

[@TOM3684]

You were right! Yes it was a cracked pvc pipe. Repairing it was a challenge because the po had a head coming off the main supply and two 3-ways off that section. Any time splicing into a buried section is tight unless I use an expanding repair piece. Maybe a video for the future?

[@garyssprinklerrepair]

I’ll send you a link to watch a video I made on using the telescoping repair coupling. kzbin.info/www/bejne/pJeWZGhnjLeXfbssi=cn1FQr7au69pDKkW Here is the correct link.

[@garyssprinklerrepair]

Great, glad you found the problem, don’t forget to Subscribe to my KZbin channel it really helps me out.🍀

[@everythinghomerepair1747]

Thanks, all of your videos are extremely helpful, keep them coming.

[@CalifGirl000]

Thank you. I was able to fix my sprinkler valve on my own thanks to your video.

[@darrellflory3822]

Great tips Gary thank you for sharing

[@garyssprinklerrepair]

Thank you Darrell, be sure to Subscribe to our Channel. We have quite a lot of content there you might find useful too.✌️

[@rm8409]

What a great video. Guys like this make KZbin legendary!

[@garyssprinklerrepair]

Really appreciated the awesome support.✌️

[@rawdmon]

Thank you so much for this video. We have rainbird valves too (I didn't even know the name of them prior to this) and this video just saved us a huge headache. My Wife's Uncle is a pro landscaper and has been helping us with fixing up our sprinkler system during the weekends. We recently split a couple of the zones which didn't have high enough pressure (too many sprinklers per zone). I guess that one of the very old valves we have is having trouble handling the increased pressure now and got stuck in an on state (couldn't get it to turn off from the control box). I shut off the water but I couldn't get access to the shut-off valve for just that set of sprinklers (I think it's pretty well buried) so I ended up shutting off the water to the house to get it to stop so we had no water at all. After watching this video I took it apart as you showed. I took a few small rocks out of it and made sure the part that moves on the inside of the screw-on cap was not getting stuck, then put it back together and then it finally shut itself off after it ran for a few seconds when I turned the water back on. I'm leaving the system shut off until the weekend when her Uncle will be back to continue working on this. We'll likely just end up replacing those parts on that one as I don't trust it at this point. Thanks again!

[@garyssprinklerrepair]

It’s normal for the valve to turn on again when the water is turned back on after a repair, once it reaches 15 psi it then shuts down. Glad to help, don’t forget to Subscribe to our Channel it really helps us too.✌️

[@dldennis5]

How do I know which one to check?

[@nessbethjanaban9953]

your so talented sir Gary enjoy what you do here to support sir

[@rosienola9805]

Awesome tip, Gary! This was a lifesaver. Thanks!

[@garyssprinklerrepair]

Glad you found it helpful

[@bigmig5015]

Great video! Thanks for sharing this tip. I made sure to replace all my valves with these rain bird brand valves so that it makes repairs nice and simple in the future.

[@garyssprinklerrepair]

BIGMIG glad to help out be sure to Subscribe and tap notifications as we will be having a Giveaway at the end of July and add new videos all the time. Plus you have access to me for Sprinkler questions notifications will let you know I’ve responded.

[@martinbobek4306]

Gary's Sprinkler Repair itrigtrol

[@garyssprinklerrepair]

Martin Bobek hi , saw your comment today was wondering what you meant. (Garys’ Sprinkler Repair Itrigtrol) on BIGMIG comment? Were you saying you prefer Irritrol valves? They used to be my favorite until they started not holding up to the test of time.

[@arifgolwalla]

Worked like a charm. Thank you for this video!!!

[@garyssprinklerrepair]

Hey anytime my friend that’s what I’m here for. Hope you Subscribe to our Channel when you get a moment.😉

[@lynnwestfall3078]

Slick !!! Thank you for the tips 😎

[@garyssprinklerrepair]

You’re welcome Lynn, hope you remembered to Subscribe to our Channel. It helps us grow.

[@jdt0045]

Great simple vid and helps a beginner to this easily.

[@garyssprinklerrepair]

Glad you found it helpful, hope you remembered to Subscribe to our Channel 👍

[@paulrobinson5492]

Excellent video! Thank you!

[@garyssprinklerrepair]

You’re very welcome, If you get a minute be sure to Subscribe to our Channel. We have a lot of other DIY videos.

[@terrihembree6266]

Worked great. Just unscrewed solenoid and replaced both tops.

[@garyssprinklerrepair]

Glad it helped you, hope you didn’t forget to Subscribe to our Channel it really helps us grow.👍

[@topsaw]

Very good, thank you, I'll try this first and if doesn't work, I'll swap the whole thing out

[@garyssprinklerrepair]

Ya, it’s always worth a try worst case scenario full replacement. Hope you get lucky with it. 🍀

[@davidriddick4905]

Great video. You saved me time and money. Thank you!

[@garyssprinklerrepair]

You’re certainly welcome, thank you. Glad to hear good news. Hope you’ll consider Subscribing to help our Channel 😁

[@freakout834]

Thank you, very helpful..... 1 question, as my cap reads 075 ASV 3/4, does it matter if new cap off new valve reads 075 DAS 3/4..... the DAS is what I don’t know meaning of..... thank you again for this video!

[@freakout834]

Thank you for replying..... Rainbird said, the system was different..... much appreciated

[@rolandomota6549]

Great job neighbor....

[@JC-hi6yi]

been doing the same thing for the large brass valves and they sell the replacement valve without the body...for $75 each...LOL I always change out the solenoid and or diaphram while I'm doing this. No sense in using old parts in your new valve. Also, on these sprinkler systems it doesn't make any difference which way you reattach the wires for the valve, they work either way. This is a great video as it shows the basics of simply replacing parts

[@eiknarfzepol]

I like plastic Hunter easy simple and cheap.. Not to mention they do the same job as the bronce..

[@garyssprinklerrepair]

Yes, some like the plastic valves too. We don’t see many brass valves anymore here in Cali. To each their own, either way sometimes swapping the tops saves the customer some money and the contractor time. ✌️

[@Kim_momshiedonna]

thank you sir gary this was a cool video very helpful information

[@clifm]

Thanks!! Saved me a lot of time and headache!!

[@garyssprinklerrepair]

More than welcome Cliff, feel free to Subscribing to our Channel for more free tips.

[@AKC2004]

You're my hero! Thank you so much!

[@garyssprinklerrepair]

You’re very welcome, thanks for positivity. Hope you Subscribed to get more DIY help.👍

[@JRLoubet]

Excellent video. Thanks for helping me.

[@garyssprinklerrepair]

Glad you were able to find it helpful, hope you remembered to take a minute to Subscribe to our Channel we have a lot more content there.✌️

[@Oscar99929]

Gary - great job - thank you sooooo much!

[@garyssprinklerrepair]

You’re very welcome Oscar, don’t forget to Subscribe to our Channel it keeps us going.

[@proskills2168]

Pretty good. Nice option to have in a pinch. Thx 4 posting.

[@garyssprinklerrepair]

Thank you

[@CD-wg6hl]

Awesome video and thanks for the clear instructions

[@garyssprinklerrepair]

Thank you for the supportive comment, it’s really appreciated. Hope you took a minute to Subscribe to my channel for more future videos. 👍

[@vilsan.r.9875]

Thank you for the tips, I personally prefer to replace all parts with the same size and labels so there's no confusion next time replacement is needed.

[@garyssprinklerrepair]

I realize that and I do that as well, but this video was for a quick repair. Hope ya got a chance to Subscribe.👍

[@Bud_NJSC]

Very helpful video, thank you. This method will surely save a lot of work I was getting ready to use your method to repair a valve for one zone (zone #3) that continually leaks from a sprinkler head when the system is off. To find out which valve was for which zone, I manually turned the solenoid on for each of the 3 valves. The problem is, zone #1 now won't turn off. I returned the solenoid back to the off position, but the sprinklers still run for that zone, so I had to turn off the water supply. I removed the solenoid and put it back on, but it still just runs Any ideas as to what the problem could be? Should I just replace that one as well?

[@garyssprinklerrepair]

Thanks Bud, most likely the O-ring on the solenoid is either torn or stretched some. I would just swap the top on that one too. Be forewarned when turning the water back on sometimes if using a Irritrol (or Lawn Genie) they will pop their diaphragms out if the waters turned on too fast. Not the case with Rainbird. Double check that the manual bleed screw is also closed. Hope you take a minute to Subscribe. 👍

[@SeekingSnow]

Thanks Gary!

[@garyssprinklerrepair]

Thank you for your nice comment. Be sure to Subscribe to our Channel for lots more help.👍

[@jpthsd]

Yep,,,that was what I did exactly today!! I have the Lawn Genie, and it was 6 screws to remove, and took the whole inner and outer out and replace the brand new one ...no need to cut, glue...!

[@garyssprinklerrepair]

Yep it’s that easy, thanks for leaving a comment. Subscribe if you like our Channel✌️

[@dldennis5]

How can I tell which valve is leaking? I don't want to use the system at all. Anyway I can just shut the whole thing down?

[@barlosvapes2465]

Gary…. You tha man!!!

[@garyssprinklerrepair]

Thank you Barlos, glad you enjoyed the video. Hope you took a minute to Subscribe to our Channel it really helps us with YT.✌️

[@barlosvapes2465]

@@garyssprinklerrepair follower! 💪👊👊

[@tienmckinnon1662]

Thanks for sharing this with us

[@garyssprinklerrepair]

You’re more than welcome glad you stopped by. Hope you get a chance to Subscribe to our channel.

[@jecknep661]

Hi Sir Gary what an amazing video . Stay safe

[@garyssprinklerrepair]

Thanks, hope you decided to stay for awhile. Where’s your channel from?

[@calistogasteve3128]

This was very helpful. Thank you!

[@garyssprinklerrepair]

Steve Moglia thanks Steve, I’ll be adding a new video tomorrow of the wireless app controlledRainbird timer so be sure to Subscribe my friend

[@janicedemoss3304]

Thanks so much for sharing your videos!

[@garyssprinklerrepair]

Thank you for the super nice comment. Hope you remembered to Subscribe to our Channel it sure does help us grow with YT

[@jfarinacci0329]

Good info. Thank you.

[@roberthall4075]

Hi Gary. I enjoy watching your videos. Thanks for helping DIYers like me. I have a question. If I have Rainbird valves just like the ones in this video and all my valves are next to my house...if the sprinkler lines run up a hill on my property, when they turn off, should the back flows completely empty out the lines every time? This is happening and I have a huge mold problem inside the house where my valves are. I don't want these valves to empty out every time they turn off. Is this normal? Thanks! Rob

[@garyssprinklerrepair]

Normal yes, the problem is easily cured by installing a spring loaded check valve on the outgoing pipes. Hope that helps, don’t forget Subscribe to our Channel for more tips and DIY fixes.

[@roberthall4075]

@@garyssprinklerrepair I’m already subscribed! I appreciate you response. I’m on it!

[@lolaecht176]

Thank you so much! Great video!

[@garyssprinklerrepair]

Always good to hear that the video has helped. Hope you took a minute to Subscribe to our Channel, there’s a lot more content there as well.

[@40redfox40]

Wish I would have thought of this years ago lol.. I’m DIYr and unfortunately never thought of that. Awesome

[@garyssprinklerrepair]

Because I give 2 yr. warranty on my valves I choose to replace the entire valve. This is however a really inexpensive, quick fix with no glue and simple household tools. Glad you liked it.🤙

[@rogergrubb]

Worked like a charm, thanks!

[@garyssprinklerrepair]

Thanks Roger, glad to be of some help. Feel free to Subscribe to our Channel, to bookmark it for later projects or questions ✌️

[@lilibetheden2826]

Oh my gosh very inspiring content thank you for sharing this sir I really Appreciated new friend from #Commander vlogs

[@debbimthompson]

Fantastic video.

[@garyssprinklerrepair]

Hi Debbi, thx for your kind words. Don’t forget to Subscribe to our Channel if you get a moment😉

[@stevereyes861]

Thank you so much..learning a lot

[@garyssprinklerrepair]

That’s what I’m here for my friend, always glad to help out. Don’t forget to Subscribe if you get a minute.

[@DC-sw9zr]

Install the brand new siliniod it's better to be safe than sorry it's really easy follow the wires it's connected to connect it back the way you unhook , it's that simple Gary didn't tell you to do that because he figures you're in a hurry sometimes it dosen't pay to hurry when your lawn turns yellow from the sprinklers not turning on

[@garyssprinklerrepair]

I have a video for a complete replacement or solenoid replacement as well. This video is just for someone needing a quick fix. Thanks for watching.

[@DC-sw9zr]

@@garyssprinklerrepairyour welcome

[@jgyamauc]

I have a bad leak at the bottom of a rain bird valve on the inlet side. I can’t tell if the threads are cracked but it’s leaking from that area. I’m guessing I’ll have to replace the whole valve. Really useful video though 👍

[@garyssprinklerrepair]

If the valve is fairly new you can simply remove it using a hacksaw or ratchet cutters. If you use a hacksaw be sure to slightly turn the water back on for a moment to remove the PVC shavings before reinstalling it. I have a video on “How to Replace a Sprinkler Valve” on my Channel. Don’t forget to turn the water main off before removing the valve. The male adapter splitting at the threads is a sign of possible high water pressure.

[@garyssprinklerrepair]

Don’t forget to Subscribe to our Channel if you found this info useful. It helps us Grow on KZbin and it’s free😉

[@trueamerican5966]

Gary thanks for sharing

[@garyssprinklerrepair]

Love the name True American, glad you found our Channel useful. Hope you have a minute to Subscribe for free obviously, to help us out as well.✌️

[@leoawag8515]

I mean just directly do manually the valves? Thank you and God bless you.

[@AB-cg6gm]

Great video thanks for making this it was very useful!

[@garyssprinklerrepair]

You’re welcome, thanks for for the nice comment

[@aswigueVlog]

Cool!! Thanks buddy for sharing this job. Awesome

[@notgoodatmuchofanything]

I love when I get the chance to make these kind of easy rebuilds...... but doesn't happen very often 😕

[@garyssprinklerrepair]

If you’re referring to the inner body below the diaphragm warping. I see that quite a bit. We have high water pressure here in Nor-Cal and it normally happens when customer uses a plastic fake rock to cover the valves. (turns them into a oven)

[@mr.g.4339]

Gary, thank you so much for the video. It made my job really easy. Appreciate it so much, buddy.

[@garyssprinklerrepair]

Sean Giloni you’re more than welcome, check out our Channel too we have over 30 Sprinkler how to videos. Be sure to Subscribe and tap notifications so we can communicate if you have questions.

[@Kris_Kringle69]

What brand is the best longest lasting valves? I’ve had bad luck with Hunter and Irritrol. How are brass valves? Price doesn’t matter.

[@garyssprinklerrepair]

MisterWin hi, I use Rainbird valves and warranty them. Use a valve blanket to cover them year round. You won’t be disappointed. Be sure to flush the PVC shavings from all pipes before installing new valves so as not to flush shavings into your new valves. Hope this answered your question. Feel free to Subscribe to our Channel for more videos coming and lots more questions answered✌️

[@EllynManoso]

Mega mega love love shout out to you sir your amazing thank you to support #commander vlog

[@lindab6901]

Thank you! I think even *I* can do this much ... provided I have the hand strength to shut off the water valve.

[@garyssprinklerrepair]

Good luck, let me know if you have any questions. Ps/ don’t forget to Subscribe.✌️

[@dmo94607]

Gary, I just installed four new RainBird 100AVSF. When I manually turn off one, the anti-siphon bleeds water for about 30 seconds. Is there an adjustment to correct, or is this s defective valve? Thanks

[@garyssprinklerrepair]

Nope normal, that’s the water returning to the valve from the area you watered. The valve is preventing back flow. Great question, hope you subscribed to bookmark the channel

[@Gossip-Nonsense]

this is what i need, very useful👍

[@garyssprinklerrepair]

Thank you Albert don’t forget to Subscribe to our Channel. We add new content from time to time.