GE washer not filling,not draining,not spinning and lid lock problem

fix general electric washer lid lock problem,blink status

[@ryankeenan351]

Words would be so helpful

[@1for4ll]

I'll do for next ,thank you

[@terryferrier8525]

I think I have this problem, but the video is too dark. I cant see where you are prying or what or where you are taking parts off of.

[@PrussianPushma]

I was able to follow along perfectly fine. Excellent video friend.

[@brianohamill7236]

Teknisimu, if I did your stretching of the spring, and still get no continuity between that spade connector and the metal piece on the far side of the copper winiding, is the winding the problem (broken)?

[@1for4ll]

For sure do the measurement the value should showed 70-80 ohm

[@fannysetiawan9611]

Finally...i can fix this macine after a long time..thx 4 info,should be viral 😊🔥

[@jasonfiz01]

I did it exactly how you showed, and now the washer machine works again! This video was a savior...thank you!!

[@1for4ll]

Glad to heard that...the problem only when the coil solenoid doesnt show the value(ohm) machine won't start

[@jasonfiz01]

@@1for4ll so I’m assuming the reason why the value didn’t show at first is just because I needed to scrape the contacts clean with the screw driver? I had issues with the lid staying locked after this too… do you have any suggestions on how to bypass the lid lock?

[@1for4ll]

@@jasonfiz01something is broken inside the latch holding the door lock .So the spring cant pull back the latch.send me the video i will help u fix it in second

[@1for4ll]

@@jasonfiz01 use papper sand gently to clean the connector and spring as well.You cannot bypass the lock because it read by system..dont bypass the cord it cause the board short circuit.U can use the machine eventho without lidlock but after 3 times of cycles it will be error again.

[@jasonfiz01]

@@1for4ll I already took off the latch and stuck it inside the door lock so I could freely open and close the washer…

[@AlbinOnishchenko]

A few words explaining each step or just shown in caption would have been helpful.

[@garystanfield2274]

SO TRUE

[@katiebug525600]

I'm not even sure what I did but this worked. Pretty sure it just had a lot of moisture in there that was causing it to short.

[@anjanileopard4489]

Thx for info 🙏..sangat menbantu ini 😊

[@CristinaGarcia-yx9qo]

buenisimo video me ayudo al 100% a reparar mi lavadora y sin pagar a esos terribles tecnicos carisimos

[@1for4ll]

Yeay good luck

[@xandervk2371]

GE updated the lock and latch. Sensing is done without contacts.

[@acts10truth]

My washer is a G.E. old fashioned stack. I messed up mine trying to by pass and it locked up. help

[@kellydavis4954]

i am getting 140 ohm, so is that a bad coil or ? i get 0.03 when touching the leads together

[@1for4ll]

Still good average .Check the terminal connection to coil

[@kellydavis4954]

@@1for4ll i cleaned the connections tweaked the spring and its back up and running. great video and thanks!!

[@1for4ll]

@@kellydavis4954 good job glad to hear you fix by yourself

[@1for4ll]

@@kellydavis4954 would you please do support to my channel by hit subscribtion thankyou so much

[@Em-lx7ek]

What model is this?

[@Mr504]

There are contacts in there take it apart clean them put it back together and now you have words to this guys video your welcome from Huffs Appliance 😁or he is bypassing the locking mechanism with the spring hard to see exactly what he is doing there isn't much light

[@celesteperez7565]

my washer worked awesome 😎

[@jeremiahshine]

Mine fills with door up. Close door it locks, unlocks, locks, unlocks. Then it ends cycle. I got errors: 14,7,19,22,5,8,13,23. Could this be the lock?

[@1for4ll]

sure its lock problem

[@rakarangga3737]

suara nya dunk sekalian 😁

[@JuanHernandez-qp6gu]

Excelente, no se tuvo que hacer eso, pero me dio una idea para poder arreglarla y funciono!

[@777espit]

Cual es para hacerla si es más simple Gracias

[@noturmomma]

Someone could have told me to unplug it first omg I just got shocked 😳

[@1for4ll]

Yes you should upluged first fpr safety

[@katiebug525600]

Yeah. I did too. Lol

[@carloscanales3183]

This guy doesn’t say a word so I have no idea what he’s doing even if I can see it.

[@PrussianPushma]

If you can't follow this video you have low iq sorry

[@michaelacoy1675]

He cleaned the contacts

[@sleepy5017]

My lid locked light is flashing too only this happened before on around Feb of this year. I still had a warranty so a g.e repairman came out and it took him all of 5 seconds to fix the issue. He said it was some computer error saying the lid was locked but it wasn't. I have no idea how he reset it or what he did to fix it but it's happening again and I'm no longer under warranty. So idk what to do. He told me before it wasn't a bad lid lock

[@1for4ll]

Its same model with yours?and now been fixed yet? I will guide u how to by pass the lock,so u dont need to buy the parts

[@sleepy5017]

@@1for4ll Unfortunately I don't think I can bypass the lid lock because my machine has a purple wire that goes with the two hot wires and it's called a "solenoid" or something and even tho we spliced the hot wires and put them together, it still throws an error at the end of the wash cycle so it won't go into rinse and spin. It's a g.e. gtw330ask3ww

[@1for4ll]

@@sleepy5017 oh it's different model but same part i think there are 3 core wire yellow and red for the solenoid lid lock and violet for the sensor to main board

[@1for4ll]

@@sleepy5017 yes you can't put red and yellow together its can short circuit your board.yes true that cycle wont finish after 3 times of cycles if the sensor of door doesnt cut off the relay that connect wire red to solenoid

[@1for4ll]

Actually they didnt reset they just change the lidlock then automatically read by board

[@lisaspees3178]

Need to talk and explain

[@paschadmlz6611]

Cara reset manualnya bgmn pak, ? Atau resetnya Auto🙏

[@rwl51]

Great explanation of what your doing👎

[@ElverGalarga58855]

Al buen entendedor pocas palabras.

[@leroygordon1614]

What you did wasn't clear enough!!

[@1for4ll]

Thankyou I'll make another video clearly step by step

[@warrior1794]

Unfortunately the Black gloves doesn’t help to see clear what’s you did . But Thanks anyway .

[@scorpionking1470]

Ge's lid lock is crappy..

[@1for4ll]

Yes, it's so bad

[@jamessmith2907]

@@1for4ll can see what you are doing need to take those CLOTHES OFF YOUR HANDS

[@francinebernal8792]

Why are you hiding your hands its hard to work on small parts with gloves on so im guessing your hiding your hands . Why ?

[@1for4ll]

Nothing to hide actually it was little bit cold the weather at here and i realised the video wasnt clear enough because of my gloves.I 'll make another clear

[@jackjill7271]

The weirdest comment ever. Most people work with gloves for safety. Anything could prick a persons fingers at anytime You must have a HAND FETISH & wanted to see his hands because honestly we’re just here to get help with the washer not worry about how someone’s hands look 🤣🤣

[@ElverGalarga58855]

He is hiding his pretty nails, you know manicure is expensive nowadays! Why risk it with a washer lid switch?!?!

[@mj6493]

I've got the exact same washer. It's the worst purchase decision I ever made. I will never buy another GE product. Shame, it used to be a quality company.

[@giselasantiago-lopez8591]

Apologies, I didn’t mean to be rude. If you can explain by speaking. I am experiencing same issue. Thank you for sharing the video.❤🙏🏼🤍

[@1for4ll]

Thank you Check my new video brother

[@user-rk8hy3xm2c]

Take them gloves off can't see what you are doing

[@endlesspassiveincome]

This does nothing for somebody that's never worked on one. When there's no talking explaining what you're even doing. If you would like some tips on getting your video seen by more people and. Showing up in search wiwhen somebody searches for something like this. Please feel free to reach out and I can give you some pointers

[@marioflores9201]

Horrible job explaining

[@giselasantiago-lopez8591]

If you don’t speak and explain, video is useless.

[@1for4ll]

Thankyou for advise Okay I ll be update next video

[@1for4ll]

Check my new video ty

[@rocker8692]

Be quiet,too much talking

[@dougmclaughlin8614]

Horrible video take it down.

[@MeaThreattoDemocracy]

No clue what you did. Couldn't see a damn thing.

[@JuanRamos-tk2mo]

Why the F are u wearing a hard hat to repair a washer ?! 🤣🤣🤣