Gigabyte AORUS AMD Radeon RX 7900 XTX ELITE 24GB UNBOXING & BENCHMARKS TEMPS PERFORMANCE REVIEW 🔥

Рет қаралды 3,310

9 ай бұрын

Gigabyte AORUS AMD Radeon RX 7900 XTX ELITE 24GB UNBOXING & BENCHMARKS TEMPS PERFORMANCE REVIEW 🔥
Follow my socials: linktr.ee/elblancoboss
Please Like & Subscribe 👍🏻
PC SPECS:
AMD RYZEN 7 7800X3D
Gigabyte AORUS AMD Radeon RX 7900 XTX ELITE 24GB GPU
32GB 5200MHZ DDR5
1TB PCIE 4.0 M.2 NVME
COOLER MASTER 240MM LIQUID COOLER
1000W PSU

Пікірлер: 26

@RouteEmpire-nn1nv 4 ай бұрын

This is cool, but I'm planning to take the Rx 7900 xtx taichi so it comes immediately with overclocking or nitro +

@coolGUGOclan 2 ай бұрын

one like thanks fro call of duty test your settings 1440P is extremal? can you made video on WarZone

@ElBlancoBoss Ай бұрын

will do in next videos. but will be the same framerate as its the same game

@VergiliyMaro 5 ай бұрын

Did box come sealed ?

@gpsousa1 4 ай бұрын

@ElBlancoBoss how much it cost?

@Bard_Emancipovani 7 ай бұрын

I have the same graphics card, it works fine, but it seems that I have significantly higher temperatures than you. I even removed the cooler, changed the factory thermal paste, and lowered the temperature, but they are still quite high. What was the room temperature during your testing, approximately? In my case, at a room temperature of 22°C, the hotspot reaches 92-93°C, with the fan running at around 60% (about 2200rpm), so it's not quiet. I have a smaller case than yours (Jonsbo D31, matx), so probably the airflow isn't the best, but still, I'm annoyed by the temperatures :D Have you done any undervolting, or are you using the default settings? Btw, the rest of our configurations are almost identical :)

@ElBlancoBoss 7 ай бұрын

Your junction temps are fine if it's in the 90s. Nothing to worry about. If it's reaching 110C then it will thermal throttle. But your temps are fine. I have it overclocked and my junction temps reach 80-90C with 50% fan speed. I have maybe better airflow in the case. I also use in the adrenaline settings frame limiter to my monitors refresh rate 165 FPS. I highly recommend you do that as well as it will lower your power usage and you will get better temps. Theres no point of having 300fps when your monitor can only push 165 for example. I hope this helps 😊

@Bard_Emancipovani 7 ай бұрын

Thank you for the quick response. I also have a monitor with 165Hz, so I will limit the FPS in the drivers. Maybe it will help, it certainly won't hurt. :)

@ElBlancoBoss 7 ай бұрын

thats good, yes try "Frame Rate Target Control | FRTC" to limit max FPS to 165, it will save power and run much quieter and cooler :)

@iiexio773 4 ай бұрын

How hard was the repaste process on this model? I have the exact same one but my Junc temps are reaching 105-110c

@Bard_Emancipovani 4 ай бұрын

@@iiexio773 The pasta won't help you; I've tried several of them. It works well for about 20 days, and then the hotspot starts spiking again at 110°C. This model simply suffers from "pump out" issues. However, there is a solution, and that is the Honeywell PTM7950, which is resistant to pump out. I installed it a month ago (you need dimensions of 25x25mm), and the graphics have undergone a transformation. It doesn't exceed 85°C hotspot even when I limit the fans to 60%. In auto mode, it stays below 75°C hotspot, which is phenomenal. Moreover, the best part is that it's a long-term solution; it will definitely maintain the temperatures as they should for 3-4 years. The replacement process is not difficult. There are tutorials on how to remove the fans, cut the PTM7950 pad to the dimensions of 25x25mm, and adhere it to the GPU (you can find instructions on KZbin for that as well). Note that you shouldn't be surprised if the temperatures are initially high; you might think you haven't solved the problem, but after a few hours, you'll see the results. It takes a few hours for the pad to "settle in," to snugly fit. That's just the nature of the material.