Glock 19 17 - slide takedown disassembly and reassembly

[@duthegee]

A video from 3 years ago still helping out people. Thanks for taking your time to make this video!

[@thenebraskan6977]

Thanks for the awesome video. Yours is the quickest disassembly video I have ever seen on UTUBE. I have always been hesitant to disassemble the upper. It’s not as complicated as I previously thought. Thanks again and stay safe out there 🙏.

[@punksnotdeaditsconservativ1693]

That makes two of us.

[@nathanskupowski4726]

@@punksnotdeaditsconservativ1693that makes 3 of us

[@ghoste2055]

Thank you I just got a new nitride slide and this video made the assembly process so easy

[@esty6983]

Thanks for the video. Solid set of paws on ya

[@dameonhunter2210]

Quick video very clear and to the point thanks man

[@youngkreisler]

Thanks for the instructions! Worked like a charm!

[@Frank-pf9iz]

Thank you this video was straight forward and I got my new slide on!

[@viintage4689]

Fast simple to the point, thank you

[@QUIET151311]

Nice job explaining everything. Thank you.

[@nelsonh.568]

That was a great video bro, I appreciate simple and correct!

[@michaelwells7311]

Great video

[@punksnotdeaditsconservativ1693]

Thanks for the straight forward, to the point, informative video.

[@matthewallen6875]

Appreciate the video. just got my new optics cut slide and this helped a lot

[@quigleypuffs]

You’re a scholar and a gentleman.

[@jaymiller338]

Best video by far, I've seen to remove the slide backplate, so I can insert a custom plate.

[@kaotick9719]

Hey loved the tutorial helped me fix my pistol and id love to thank you agian brother be safe and god bless

[@MrBeachDoctor]

great vid, thanks

[@shrmp5451]

One of my springs and plunger went flying and I didn't where it went

[@jayman3573]

No cleaning oil or anything needed?

[@AKjose47]

This was just a take down and reassembling but for cleaning I would use a cleaning solvent and soak for a bit then clean it off with a clean cloth or rag. You can use a dental pick or similar tool to scrape off any carbon build up if needed. Then use very light oil like CLP or any gun oil and use a little on the springs. Very little. And oil, not grease. The recoil spring is the only spring I would even consider using a lithium grease on. But I still prefer oil for that as well.

[@rdudeb5058]

Thx

[@didisaythat4230]

Very quick and detailed. You dont see videos like this very often anymore. Im having exteacting issues on my p80... how likely is the exteactor to be the issue? Im aware of the one part that people often times swap out. Im just wondering if the extractor could possibly be the issue. It just doesnt seem to kick the shells out.

[@AKjose47]

I’ll say this: if you have a optic cut slide, your problem very well might be that the optic cover screw or optic screw on the extractor side is probably too long and interfering with the extractor rod. You’ll know if this is the case by trying to remove the extractor rod and if does not come out freely then there is interference there from the screw. If it comes out freely then of course make sure it is installed in the correct orientation, spring and bearing should be towards the back of the slide and rod should be up front against the actual extractor. If that’s good then the extractor itself could be the issue.

[@victordiblasio3019]

Can you do a Glock 19 (preferably gen3) lower frame assembly ?

[@AKjose47]

Coming right up

[@texasmufucka]

Much appreciated brother.

[@yxngfolks223]

My spring keep falling how do I fix that ?

[@AKjose47]

@@yxngfolks223 which spring? I’m guessing the trigger safety plunger spring. I would put the spring on the safety plunger then hold the slide, sights side up, and put plunger and spring in from the bottom up so the spring doesn’t fall. Once it’s in, make sure it is in there and not binding up. Once the extractor is in the plunger will stay in place.

[@doulatram5919]

Exlent 👍

[@K1ngDre-DMZ]

Dude you rock! Thank you!!

[@WN8HGZ]

Very good should those parts be lubricated before putting them back in to the pistol

[@AKjose47]

On the slide I only lubricate the guide rod/recoil spring and the rails that ride on the frame.

[@warningshot910]

Wait, this aint airsoft

[@ghostblack9209]

Big meaty claws lmao

[@jasedelgadillo9137]

Is this gen3 or the same as the gen3?

[@AKjose47]

This is a gen 3 but they are all the same pretty much.

[@jasedelgadillo9137]

@@AKjose47 thanks man I was able to change out my upk to my new slide no problem thanks to this video👌🏽

[@ItchyPilauBoto]

I hear Tribal Seeds, your arms are super hairy lol but thanks for the video bro.

[@AKjose47]

Lol thanks for that?

[@masteryoda3558]

Isn’t that roller skates by steel pulse?

[@DavidLLambertmobile]

The music, noise in the background is a distraction. ⬇️

[@battleborn2002]

POORLY DONE!

[@AKjose47]

I made this video for a customer that ordered a slide and was scared to disassemble his oem slide to instal the parts I to the new slide. Sorry to disappoint you lol. Maybe you can make a better video and finally upload something to KZbin after 14 years?

[@BobbiSkankanos]

half the video is over before this genius gets the backplate off! then on reassembly, reinstalling the extractor, he says "round part goes to the back" except he shows no round pat and there is no "rtound part on the back of the extractor!

[@AKjose47]

Thanks for watching