GM A, F, & X Body Disc Brake Caliper Brackets Nova, Chevelle, Camaro, Firebird

Step by step instructions and helpful Tech Tips when installing your disc brake conversion kit on your Chevelle, Nova, Camaro or any A, F, X body Vehicle! See our kits for your GM A, F, X Here! piratejack.net/1964-1972-gm-a-...

[@fasteddie4145]

I always love these videos that show the nuts and bolts on 50 year cars that come right apart......every single nut and bolt on my '71 Chevelle required a blow torch, hammer and sawzall to remove.....

[@mcrickyd32]

Hahahaha same. Like it seems these shows do the job, put the stuff back on and then re do the job for the camera and every bolt breaks free with a regular size wrench or stubby ratchet handle.

[@juliobello4561]

Question I'm quite new to this stuff so I can use the stock brake lines in 4 disk brakes in a 93 Silverado

[@darinandalinahouse9596]

Wait a minute. When you bench bled your MC you didnt even have the return tubes down in the fluid. Ummm... lol At any rate, thanks for making this video. Really helpful.

[@martysheets6882]

Great how to, Thanks.

[@jayrocwitdalocs2653]

Will this kit change the offset

[@simonh5110]

Got anything for rear disc conversion kits for a 75 el Camino?

[@caimenwillson5427]

I just installed and it spun freely but when I installed the brake caliper it doesn’t spin freely it grinds when I spin the rotor what do i do

[@stanshuba2191]

Love polka music

[@lewisnaquin8481]

first time i am pretty good at it

[@txprospector]

What I want to know that no one has ever answered is if you have the distribution block that was originally mounted on the frame under the car how do you connect the brake lines to the new proportioning valve located on the master cylinder?

[@georgearce5098]

Did you get your answer? I'm curious, I have a 64 A body with power drum brakes.

[@txprospector]

@@georgearce5098 No I never got an answer. I just mounted my proportioning valve in the original spot and ran lines that were preformed like the originals. I think I got them from Ecklers.

[@dustingarcia4264]

Any options for a 65 Chevy corvair? I'm having trouble finding any info on disc to rotor kit for corvairs

[@colinrutter3545]

Dustin Garcia corvair.com or California corvair parr’s.com

[@johncollins6023]

Anything on rear disk brake conversions for 76 Camaro?

[@pjack3989]

Sure do! We have drilled/ slotted or standard rotor kits. Give us a ring let's help you out. 866-601-4455

[@davidmcnallyjr3441]

my dust shield rubs on my lower control arm so cant finish. why? 68 camaro disc brakes all new parts

[@Chefboyardarryl]

Shouldnt need it, or trim it.

[@alexe3586]

i bought this kit but i used the old spindle...the rotor is grinding against the top hex bolt...how do i fix this

[@brandonrothrock5846]

alex e by putting the new spindle on

[@djjoshsanchez]

Hello I have the same brake caliper set up and after i install the caliper and spin the rotor. The outer brake pad rattles, like its loose. how do I correct this?

[@pjack3989]

Sounds like you are missing a brake pad clip. They hold the pads in place so they don't rattle. Also sometimes called anti rattle clip....

[@djjoshsanchez]

P Jack I purchased these rattle clips that were recommended for my nova. But im not sure how to install. I know that the bigger size are for the inner pads but im not sure how to install the smaller clips. Any ideas? shop.advanceautoparts.com/wcsstore/CVWEB/staticproductimage//2566/large/22141334_rnb_26210_pri_larg.jpg

[@markpalio5786]

I know this is an OLD Post but Someone may have the Same Question- if the OUTER PAD is Loose in the Caliper(and Moves) then the Top Tabs need to be Slightly Bent by Tapping with A Hammer, Until the Pad is Snug in the Caliper.

[@yukon1000]

Would this kit work on a 1967 Impala?

[@pjack3989]

No it won't work on the Impala but this kit will piratejack.net/1965-68-chevy-impala-power-disc-brake-kit-black-wilwood-calipers-master/ We have other kits in our store for just about any build.

[@kevinmahoney7468]

What do I check for if the disc does not spin freely

[@txprospector]

Loosen the castle nut 1/4 turn on your spindle.

[@dennissutton223]

Parts are from MBM, my kit had standard rotors that were junk, the rear races were off center and one was not seated, very dangerous! No help from MBM! Had to purchase good rotors to complete job!

[@SashaZvyagin]

Where did you guys get the kit from?

[@markcernicky5335]

I need a kit to update the front brakes on my 1973 Ford Van.

[@novabbc]

did you have to torque anything

[@pjack3989]

Yes. All torque specs are in the install manual when you buy the kit. Hope that helps!

[@arthurporrata8882]

I'm a little surprised that you don't use torque wrenches.

[@nickrodriguez7293]

It would help if you torque the damn thing down

[@pjack3989]

You can't use the old spindle when doing a conversion kit. You will need to change out your spindle to a discbrake spindle.

[@stefanbogunovic5661]

+P Jack -if that is the case then why do they sell kits without the spindles

[@dylangreene8756]

Stefan Bogunovic you can modify the old spindle by cutting .6 of an inch off the top boss and it'll clear the caliper bracket. poor mans methods that'll get the job done.

[@daronedward7864]

Dylan Greene

[@TheCurtisdaffern]

They did not hook up any brake lines to the car, That was at least an incomplete kit. The way they left it there would be no brakes at all.

[@thewhiteelephant]

The car already has its own brake lines. You hook those up to the new components. If you need new brake lines, you can purchase them as a kit. I’ve yet to see a kit that includes everything in this video plus the brake lines.

[@fiddlerpin]

Seems that they don't answer questions from viewers.

[@209chevymon]

Thats when you say to yourself if they dont care about there customers you shouldnt care about there product and look else where!

[@seanseanseanseansean]

Can you remix to eliminate that worthlessly loud filler MUSIC?