GM Vehicles 3.1L & 3.4L V6 P0341: Camshaft Sensor Replacement

You can grab the new Cam Sensor for a great price on Amazon Here-(check fitment guide)
amzn.to/1SQrrJ2
BSG Automotive offers Auto Repair services in the greater Chicagoland area.
Website:
www.bsgautomoti...
Facebook:
/ bsgautomotive
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user and BSG Automotive (hereinafter “BSG Automotive”) makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. BSG Automotive shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by BSG Automotive and therefore, BSG Automotive does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge BSG Automotive or anyone affiliated with BSG Automotive, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

[@Delerium682]

Finally! A video that actually shows what the darn bolts look like! "Pro" Tip: Don't take your vehicle apart over the course of years without labelling things or you too will be spending hours trying to find a video or pictures of stupid bolts! P.S. Irony is I used the 5.4 Triton timing videos to fix my truck about a year before I found this video.

[@mikebrennan4534]

if the wires break off the sensor and the sensor stays stuck in the engine (way too common). screw a long drywall screw straight into the sensor and then use pliers to remove. i have had to do this dozens of times

[@BSGAutomotive]

+Mike Brennan yeah I had my mini slide hammer with #8 wood screw ready to go but I was very lucky

[@ricardmcgee2235]

Mike Brennan a 94 Chevy aluminum SUV a 94 Chevy SUV camshaft sensor

[@carlospaz8646]

Thank you sir! I was wondering about that. 👍

[@FEARxTHExBEARDx34]

This video is a god send. We were looking yesterday and thinking ok, washer reservoir out, alternator out and power steering pump as well. It's a good thing the only thing pulled so far is the washer tank🤙

[@scottrussell3553]

Thanks big time. It’s guys like you who make the shade tree mechanic look good.

[@jayfinesse7231]

Thanks for this video. I was able to do this job in a couple of hours, and so far the car is running smoothly. You almost scared me off with the bit about supporting the engine, but I found a different video that briefly showed it, and I was able to figure it out. Don’t know much about cars but it wasn’t as bad as I thought. Thanks again

[@cap8e]

what was that video?

[@wysetech2000]

Nice job, Brian. I have done a few of those myself and you made it look easy.

[@jahn24]

good video, camera angles could see what was going on. good audio, clear procedure explanations. best of all... he didnt try to be funny, or cameo shots of a dogs ass, or talk about his vacation.... just to the ponit on how to do the job. great video.

[@michaeldelorenzo8006]

Well we’ll done video idk if I could of done it any better or showed it as easy as u did plus it’s perfect for ppl whom don’t have special tools like tensioner tool extra . Good job sent it to my daughter in Florida and she was able to understand it better then me explain it to her thank you 👍🏼🤙🏼😊🙏🏼

[@aladinsarsipeus]

For once a clear and concise video that actually shows you how to do something No camera wind noise no heavy breathing no babbling no constant tools constantly click clacking against the throughout the entire video Thanks dude👍🏼👍🏼

[@dannyhampton711]

Where does the other end of the wires connect or do they hang loose?

[@vincentesolon2210]

Very perfect in every way ie clear and to the point and reassuring . thanks

[@frankromero3198]

Thank you for your support and help greatly appreciated 👍

[@joewilson1522]

Just got into bed after doing this and oh my god was it hell first my csp sensor got stuck the plastic housing around it snapped after using it for leverage couldn’t route the wires through how the oem ones where (under a vacuum line) once i finally got the damn steering pump back into place I spent a good half hour just trying to mount the pump because the thing wouldn’t stop moving anyways a few swings with a breaker bar swears and curses and now dedicating one of the said bolts to the extra optionals pile I now have a stripped battery terminal and have to wait on that very fun gm very fun…

[@marthaivonneacevedo4004]

Your video was loud and clear, thank you.

[@kristinroney7591]

Best video I seen for my car. Thank u

[@ladyshiva69]

where did the sensor plug go into ? how high to go up with engine

[@tonystarx5092]

Great video it was very detailed and simple

[@carwashrodriguezjr7113]

Very good video I congratulate you, thanks for sharing these videos .. greetings from beautifull sonorous mexico !! joshua rodriguez .. I subscribed to your channel !

[@jimmyjimjims7483]

It's a good video but unfortunately this does not apply to the 3.4L V6 in a Buick Rendezvous as the PS lines are routed UNDER the alternator not on top like yours. Now way for me to remove the PS pump without disconnecting the lines (thanks GM).

[@bobdroidsky225]

Nice video, Brian. Can you please explain in more detail how to support the engine with your method (wood and jack)?

[@bobdroidsky225]

Haynes suggests using a 3-point engine support fixture www.amazon.com/OEMTOOLS-24951-Point-Engine-Support/dp/B01GGBOQT2

[@ryans413]

Place a block on the jack and jack up to the oil pan and just lightly push up on the engine not too much just so it supports it not pushes on it

[@46lfries]

You don't have to pull the power steering pump to do that

[@ryans413]

How do you do it then

[@46lfries]

@@ryans413 channel light down in there quarter inch drive 8 mm maybe with a flex on it that's been a couple years ago since I did that get a hold of wire and jerk it out

[@richardbeal2790]

Some later models I've come across require the removal of the power steering pump pulley to gain clearance past the intake and front cover there, so some viewers will want to make sure the have a puller or rent one from a parts store. I like the wood screw technique, I'll have to try that if I ever have the wires break.

[@MrMDee-si1bz]

Great vid! Dude! Thanks for sharing! 👍🏻👍🏻

[@reynaldimoore3140]

Best how to video man keep up the work I'm having problems with my 04 alero would love if you good give me some pointers

[@clampaholic4782]

What tools did you use

[@koreymayo8884]

Was hoping you would've shown where the wiring harness goes.

[@EPerez-iw9zp]

What are some symptoms of a bad crankshaft sensor

[@ryans413]

Hard starts rough idle loss of power engine stalls bad gas mileage

[@enigmanity]

What should I do if my camshaft sensor is stuck, I tried to pull it of same way the guy in the video did but the wires came clean off and I'm stumped..

[@BSGAutomotive]

The sensor is plastic so what you do is screw in a drywall screw and that gives you a place to grip onto it with a vice grips to wiggle and twist it out.

[@55crimmer]

BSG Automotive

[@PatRiot-]

Never ever grab and pull anything by the wires.... That will prevent another accident next time. You are looking at a good set of circular grip plyers Or rig something up with zip ties around the sensor and pull with a better tool

[@enigmanity]

I ended up drilling a screw into it then pulled it out with some pliers

[@jameslamson5092]

It's possible to put a small flat blade screwdriver to the edge of the sensor and gently tap it under and pry a bit and it should come out. If you broke the wires, the pigtail is available for the replacement sensor or a separate part. And just splice the new pigtail to the old wires and it's a fix.

[@ricardoacosta7394]

Buen día, q sensor es el que cambio? saludos

[@thomaslonghway4039]

Is this most of the 3.4 locations on silhouette

[@agri-lifeorganicfarm2466]

Another great video.

[@troyelliott8186]

Could you just remove the power steering fluid housing to get access. The part that contains the power steering fluid

[@mwegner32]

I liked and subscribed....I love videos like this they give me confidence

[@trinity9523]

Since I own a 2001 alero v6, is the sensor positioned the same. Also the code I received is p0336, would those be the same or different sensors

[@gristlevonraben]

Thank you

[@adamkelley6316]

I haven’t been able to find that part? The ones at auto zone are different than that

[@user-tz1oj9hd6m]

Get some one to get number or letters Off of it and color and Look it up on a Line it be cheaper to and what car it comes of don't take but 3 or 4 days to get it thru mail from a car company

[@girlythug7223]

Hi does the new one comes with a wire?

[@ryans413]

Yes

[@jameslamson5092]

not certain but would that make a car like a Malibu run rough and often start with a jerk when placing into gear? Help!!

[@Airwolf2030]

my family member has a similar engine to that but it's a 3.4L V6 3400 from a 1999 Oldsmobile Alero, is the sensor in the same location?

[@Airwolf2030]

never mind, I looked at the title and answered my own question lol

[@mylesgarrett7830]

Ok so I forgot to disconnect battery what do I do

[@frankdowning5929]

What is going to stop that thing from starting in the morning the camshaft there going to be is causes a cold start I don't understand why it won't start in the morning that's it gets above 50° it'll start I don't know why

[@carlaclark7682]

I have a 2009 impala and I need to replace my camshaft but can't find nothing on the internet on how to do it for my 09

[@nandogutierrez1223]

thanks bro helped out a lot !!!

[@joseruiz540]

What the little black cap that you put on it .whats it called and were can i buy it

[@VicSG]

Good job... Excelent

[@salsan8896]

good video , thanks for share

[@gypsyedc9143]

Thanks 👍🏻

[@marianne8636]

How long does the sensor replace take???

[@willquaas]

I did this today in about 2 hrs on my 99 malibu. My car still wont start...wants to start but dies right away. attempting fuel filter replacement tomorrow

[@wades623]

sounds like it might be the key switch. i had one of those and thats what it was

[@user-zb7xp4mm9w]

2003 intake gasket replacement

[@Thecaresnail]

I have a 1995 Pontiac Firebird with the 3.4 l I have no spark I have changed the coils I have changed the cam sensor and I have changed the ignition module what is left with a bad crank position sensor make it not run even with a good cam sensor please someone help me I do not understand

[@nathanielmanns1055]

2004 Impala won't turn over what is the problem

[@TyhlerNovac]

I was able to change my camshaft sensor do to this video but now I cannot get the code to clear what should I do next

[@TragicDownfall]

Tyhler Novac Same I’m having troubles did you find anything out?

[@caucajunman5930]

Dam good job!

[@jamescurtiswalker1]

thanks.

[@tonyahorner4213]

Does anyone know where the crankshaft sencer located on a 2000 buick century 2000? PLEASE ANYONE HELP

[@jankball9843]

2002 as well...

[@Mr.Frost181]

so is this what makes your car kill sometimes when you start to push down on the accelerator cause when I started my car an then began to leave my car just stop on me an I had to restart it again an it been doing this so when I got a test on it this the code that it gave me saying it was the camshaft position sensor..... let me know bro

[@barnettelectronicsreviews3797]

QUINCY WILLIAMS my 1993 camaro 3.4l died on me while driving 5 times while driving it would take a minute to start back up was this cam sensor the problem

[@Mr.Frost181]

Mine to

[@jameslamson5092]

My 3.1 engine is running rough and should not run rough and starting from idle with a jerk. Next, change the sensor that is already giving s 341 error plus it added a 118 error.

[@Mr.Frost181]

@@barnettelectronicsreviews3797 got it fix on my monte Carlo an never stopped on me since drives real good an had a lot of things change on it recently

[@johanplevello8377]

Ecxelent video

[@philh9238]

forgot the gm crank/cam variation relearn....

[@BSGAutomotive]

+phil holbrook yeah but is it really necessary for a cam sensor? I know crank sensor replacements are a must but not cams. Is this a GM thing?

[@philh9238]

yes. its a gm thing. itll throw a cam/crank correlation code if it isn't done. I didn't do the procedure once and it was a comeback

[@sneakysnakepie1]

you only have to do it if you change the relationship between the crankshaft and harmonic balancer. Like replacing the crank or harmonic balancer and etc. the sensor has nothing to do with a relearn. since all it does is read them. so as long as you get oem parts you shouldn't have a problem. I've replaced the cam/24x crankshaft sensor on a beretta at the same time and guess what. I didn't do a relearn and it's a 96 model.

[@BSGAutomotive]

Yeah that is what I though same on the Fords only if the crank pulley was removed and replaced the relearn needs to be done. The customer has not had any codes pop up and has passed emissions testing so they are happy!

[@lucianoromero777]

I have a Z34 Monte Carlo I have a Haynes manual and I took the pump off and it says it is right there for 3.4 engines, I do not see this thing dude. Help lol

[@tonitoni3134]

is that's don't start car because of that

[@Kelbo3575]

Toni toni

[@adrianwallington5359]

Damn thats why i cant get it to come out did not move pump

[@marshall1157]

good vid but i need sensor b not a.

[@jimroy5771]

wers it at on a. 3300 oldsnoble classe cera

[@JasonfromMinnesota]

Thank you for that

[@SMZXmazum]

mahindra scorpio crde engine same code dous not stert camshaft sensor change for wearing cheak

[@mikehernandez7837]

Fordtechmakuloco has nothing to do with this video i follow you here in this channel and the other I'm interested in buying a newer Ford Taurus 2010+ I wanted to know what are some of the persistent repairs on Taurus ?!?!

[@mikehernandez7837]

BSG automotive?!?!

[@nenareveles2950]

En español

[@HATTAFRASHED]

the most bad car

[@dab-pre-ss-ionaustin1986]

Did this n now my car blew the motor da fuck brian lol time for a motor swap now

[@ddjthemultimusicalrapper]

I have a 3.1L and I can't get my belt off because the strut tower is so close how can I replace my sensor can someone help?

[@ddjthemultimusicalrapper]

My car is a Pontiac Grand am GT

[@mylesgarrett7830]

Ok so I forgot to disconnect battery what do I do

[@user-tz1oj9hd6m]

Put it back in then disconnect the Battery

[@SMZXmazum]

mahindra scorpio crde engine same code dous not stert camshaft sensor change for wearing cheak