👨‍🔧Go Go Mobility Scooter Repair Guide Part 1 The Tear Down

[@ChristianCarnivore333]

The most thorough breakdown video I've ever seen, tremendous job Sergio!! Thank you so much for your help :)

[@MobilityDirect]

Thank you so much @ChristianCarnivore333! We always want to be informative and make sure our videos are also easy to follow. Happy that you like it. Thanks for the support!

[@johnfirth7586]

Thank you for your clear instruction so far. I need to see how you remove the batteries from the holder and replace them with new ones

[@MobilityDirect]

Thanks for watching! Check out this video to see a Gogo battery replacement: kzbin.info/www/bejne/f2fHlGyMe9Z3gcU

[@ronalddaub5008]

Before I put grease in my gearbox I put new batteries that I did not need in mine but it was really easy .

[@pchristopher174]

Probably the best support video I have seen on any topic! Super well prepared. Looking forward to part 2 (if it is already online- please give the link). I think my model is the one you use in this video. My problem is that even with the battery charged, and everything put together, the freewheel lever is in the Drive position, when I turn on the ignition key, the gauge shows the battery is charged, then, either forward or reverse it moves about 3 inches and stops. Usually beeps 6 times. What should I be looking for? Any suggestions will be appreciated. Thanks.

[@RobertWilkinsonJKekMaloy]

Thank you. Tried to fold one down using the manual with no help. So not the right book. Found you, watched ya and now our issue has been resolved. Thank you!

[@MobilityDirect]

Glad it helped 😃

[@dcurzon1973]

Thankyou! I picked up a used Elite Traveller LX (UK model, might be called something else in US, but its a 4 wheel model) for my dad, which was all working ok but a bit filthy, so I gave it a thorough washing, which led to (or highlighted) a faulty horn switch... after replacing that, I then suddenly had no diagnostic beeps, only 'clicking' which sounded like a solenoid which left me a bit baffled... but thanks to this video, I discovered there's a 2nd piezo buzzer hidden away in the chassis which seems to be the culprit and I have a replacement arriving today. Couldn't find all the screws to remove the floor pan on the Elite, but was able to remove enough to flex it and get a hand in and find the buzzer and cabling, so should be all done this afternoon so I can deliver it to dad this evening :) If you have a tear down of the Elite Traveller, that would be awesome (or just the front section and leave the rear/motor) - thanks

[@MobilityDirect]

Hello Darren, we might be able to do that for you but these videos take a long time to make. I can't for sure say when it will be done, but I'll try to get one done for you this month. :) Thanks for watching, I'm glad you enjoyed it. BTW I'm almost certain the front half of the Go Go Elite Traveller is almost identical in the way its built compared to this model in this video.

[@dcurzon1973]

@@MobilityDirect Thankyou for the reply, I have managed to replace the under chassis buzzer, but I was still unable to get the floor pan removed, so I've just tucked in best I can which should do the trick, certainly temporarily anyhow... but a breakdown video would be so useful! thanks again :)

[@MobilityDirect]

@@dcurzon1973 you got it!

[@sandrazeiler4194]

Looking for parts for a go go elite traveller scooter S44E

[@shirleywhitlock3756]

Hello I like that every question someone has ,you answer it that is great costumer service, thank u God bless u all that work to make things easier for us...

[@MobilityDirect]

Thank you so much for your comment. We value our fans and customers. Each and every one.

[@stevehensley1737]

Very thorough video. showed me what I needed to know.

[@MobilityDirect]

Glad you liked it! Thanks for watching our video and commenting! If you're in the market looking for a mobility scooter, please feel free to give our non-commissioned sales expert a call at [phone].

[@ronalddaub5008]

I ended up with one of those three wheelers with a lot of miles on it. It took a lot of amps to turn the gearbox and when I took it apart the grease had turned into dirt. I got it cleaned up and there wasn't any wear on any of the Gears. it was amazing. now it's got new grease in it and spins so good that it doesn't hardly draw any amps unless it's going up hill.

[@MobilityDirect]

Awesome!

[@ronalddaub5008]

@@MobilityDirect on these little ones friction or the lack of friction can mean a longer battery life and better performance

[@prestonhall1556]

Excellent

[@MobilityDirect]

Thank you!!

[@nirvanakurt8334]

Thanks for your information , its really help.

[@MobilityDirect]

Happy to help!

[@jomareli]

Hi, I'm Brazilian and I have one of those tricycles, I live in the countryside and it's very difficult to find parts for maintenance. My tricycle ruined that connection part of the rear part, it broke. so I made a direct connection from the back, connecting the wires. then it started working again. Now I'm having trouble removing the rusty rear wheels to replace the tires.. this disabled life is very difficult. sniff. congratulacions

[@MobilityDirect]

Once they get rusted, its all downhill from there. You will likely need a new transaxle.

[@johnmejia399]

Awesome video. Very informative.

[@MobilityDirect]

Thanks John! 😁

[@debd7803]

I have a question about something not mechanical or anything. What about the clear like tape where the rear and front come together. Is there a replacement for that or is it only there to keep the paint from getting scratched and is really just a visual thing. The "tape" on mine is worn off for the most part. Will duct tape or maybe some kind of packing tape work good enough? Loved the video and helped a lot when working on a 4 wheel version. A little different as far as the front disassembly but close enough.

[@MobilityDirect]

Not really but if you get some sort of black acrylic paint you could just spray paint it to make it look new again.

[@citlalie9791]

My power connector from the back broke how do I replace it?

[@MobilityDirect]

If you need to replace a part, you can give our Parts Department a call at [phone]

[@georgedoughty6679]

Great video

[@MobilityDirect]

Thanks George, glad you liked it. If you have any questions, don't hesitate to call our non-commissioned sales experts at 877-721-7748. We'd love to earn your business. :)

[@dons.7381]

Purchased one of these 4 wheel ones with rear brake light. As we use it in the evening we. need rear lights. Presently added some battery lights, used in house cabinets, and glued them to the back. Have a remote control to change colors of light and on and off. What I would like to a real red light connected to the circuit that turned on the front light, to permit visibility. Any suggestions on how and where to make a connection.

[@MobilityDirect]

We cannot really make a recommendation on that as it would void the warranty and possibly create an issue with balancing the batteries.

[@jeaninejurado3733]

I have a question pertaining to my Go Go Elite Traveler scooter. I noticed the tiller charging port was not charging the battery. I checked the fuse (which I would like to verify if that should be a 3 amp fuse) and it is intact. What else could be the issue? I enjoyed the video and appreciate the inner workings of the Go Go scooter series. Thank you.

[@MobilityDirect]

You may just have a wire that is disconnected somewhere. You need to take the scooter apart and check all the connections. Perform a "tug test" on all the wire clips, sometimes the wire will disconnect from the clip and you won't see it because it happened within the wire sleeve. Start there, then see if you can put a multimeter to the charging port while charging, if you aren't seeing the volts go up by .01 volts at a time, then the charger is bad.

[@jacklee2405]

on our scooter the connecter on the motor to the battery have mail connecter from the motor end and female from batterie we have a broken pin on the mail connection can we get a pin to replace the broken one that is on the red wire into the motor

[@MobilityDirect]

@jacklee2405 For parts related inquiries, it's best if you call our parts department, so they can accurately answer your question. You can call them at [phone]. Also you can fill out the parts request form on this page for a quicker response: www.mobilityscootersdirect.com/parts-request

[@richardbarkley9909]

I was hoping that you would show replacing the tiller fork bearings. I believe there is an upper and a lower ball bearing ring but can't confirm because I think my lower has blown out and the small ball bearings all over the ground.....Thanks!

[@MobilityDirect]

That's VERY unusual. We don't ever get calls about the tiller fork bearing breaking. How did that happen?

[@anniescolourfullife]

An interesting video, thanks. I like to see how things work........I remember pulling a watch apart when I was 8 years old and I put all the bits in a matchbox. My mother wasn't very happy that I'd ruined a new watch🤣🤣. I certainly have no intentions of dismantling my scooter 🤣 (it's still under warranty anyway) as I'll be sending into the shop where I purchased it here in the UK for service and any repairs that may arise. I'm actually rather disappointed in Pride customer services here in the UK........sent an email asking if my scooter warranty will be affected if I put lithium batteries (first asked local mobility shop if lithium can be put in my scooter model) in my scooter instead of the lead acid, but they've not even had the courtesy to reply. That has actually put me off buying any further Pride scooters in the future.

[@MobilityDirect]

Unfortunately, Pride in the US has told us they will void the warranty if lithium is installed. I'd imagine they'll keep the same standards in the UK :(. I would wait until your warranty is over and you need to replace the batteries, and then upgrade to lithium!

[@anniescolourfullife]

@@MobilityDirect I guessed that would probably be the case with regards to the warranty, but thought I'd ask them. Yes, as Pride UK couldn't be bothered to reply to my email, I decided to wait until the warranty expires before either changing to lithium batteries or purchasing a new scooter.

[@ballkeeper6662]

can you do the same strip down on s4

[@MobilityDirect]

Great idea! I will definitely pass it along :)

[@john6853]

How do u service tyres and tube’s

[@MobilityDirect]

It depends on the model of scooter. What kind do you have?

[@TeenaWhitney-yg3cf]

Thanks

[@MobilityDirect]

Thanks for stopping by our KZbin channel! Don't forget to subscribe for a chance to win a free mobility scooter.

[@stanleywilushewski8010]

I have a pride victory 9. Is there a setup to have turn signals front and rear and possibly a brake light

[@MobilityDirect]

Unfortunately, it's not possible through parts that are made by the manufacturer... You could probably get some sort of bicycle light kit and retrofitted to your scooter.

[@grahambenning4047]

My scooter had an erratic battery gauge and stopped after a short run it was the batteries new ones fixed the problem

[@MobilityDirect]

Thanks for watching and commenting, I'm glad you got it all worked out!

[@rayeannhelms6612]

Does the front to rear wire harness that connects the dash controls to a connector fit through the tiller? Buzzaround GB106

[@MobilityDirect]

Yes.

[@steveho9884]

Show the battery please how long I charge it? how far can go with it

[@MobilityDirect]

You can charge these overnight if they're fairly depleted, or just a couple hours to top it off! On a single charge, these scooters can go an average of 8-10 miles :)

[@kimberlysmith2526]

I have a gogo elite scooter I'm needing a part can you tell me what it is I'm thinking it's a gear

[@MobilityDirect]

@kimberlysmith2526 For parts related inquiries, it's best if you call our parts department, so they can accurately answer your question. You can call them at [phone]. Also you can fill out the parts request form on this page for a quicker response: www.mobilityscootersdirect.com/parts-request

[@raymondj8768]

HI i have a gogo elete traveler hd 4 wheel scooter its n older one it beeps 7 times and won't move at all i have two new batteries it used to have an intermit problem but now shes just dead fuses are good do u have any ideas off hand i would really app any help you could give me thank you very much sir .

[@MobilityDirect]

7 beep code usually means the potentiometer is going bad or there is a throttle lever trip. That model has been discontinued for a while now. We have some great options now, and plenty of inventory on the newer models. They are designed with good quality parts and comfort in mind. Give us a call if you'd like to speak with a non-commissioned sales expert. 877-721-7748

[@normlewis1984]

Could someone PLEASE tell me the proper name of the little horn on the Pride Go Go?? I repaired mine once, but I do believe I need to purchase another. Thanks!

[@MobilityDirect]

We'll probably need to check that with the manufacturer. Please feel free to give our parts department a call at [phone] so we can help you check and purchase it. Thanks for watching!

[@marvinermshar581]

Can the fuse come out without taking the shroud off

[@MobilityDirect]

You'll still need to remove the shroud. Thanks for watching our video and commenting! We appreciate the support.

[@VideoAmazed]

My father's Go Go Mobility Scooter "Elite Travel Plus SC-53 has what appears to be a bad or dirty speed control-potentiometer for the speed control ? Can they be cleaned with electronic CDC Tuner aerosol spray without removing ? Have they been prone to be defective ?

[@MobilityDirect]

You can attempt to clean it, they are not really known to be faulty.v

[@jimprine7522]

Mine blinks a 7 beep code 9 times out of ten when you turn it on but then it will act normally. What up?

[@MobilityDirect]

Check out this forum post we made about this subject: www.mobilityscootersdirect.com/forum/knowledge-base/pride-mobility-go-go-scooter-beep-7-times/

[@Mr71chevyvan]

i own a blades sport dks200 w/a funky controller, do you know how i can access it ?

[@MobilityDirect]

Unfortunately, we do not sell or service those, so I do not have a clear-cut answer for you

[@carolcollins4673]

I'm waiting to hopefully get some help finding out why my scooter doesn't send connection to the front for electrical

[@MobilityDirect]

Good luck!

[@grahambenning4047]

@@MobilityDirect The controller

[@Brazier117]

Hi is there any way to change the speed of the gogo elite traveller mine stuggles to get up inclines and I was thinking if I could get a bit more speed it would be better up hill I know there is a limiter on them but have no idea where it is or how to adjust it if you could get back to me I would muchly appreciate it great video by the way

[@MobilityDirect]

There are no limiters on gogo mobility scooters and absolutely no way to make it go faster. Sorry, the only way to make it faster is to replace it with a faster scooter. We just made a video about this if you look at our most recent videos. I think you will love it.

[@jacklarson6281]

do you have a vid that covers error code 5? Solenoid Break Trip I tried the operators manual's solution and I think the problem might be either the electrical connection to the motor, or a mechanical issue inside the shifter.

[@MobilityDirect]

We do, it's the brake lever in the neutral position. You must have it in the drive position.

[@kenthoren3578]

I also have error code 5. However, it is always on no matter the position of the brake lever. Is there a way to test the voltage at the motor for proper operation?

[@MobilityDirect]

@@kenthoren3578 you may need to replace the electro magnetic break assembly.

[@martinkennard1669]

Bummer! You didn't show how to disassemble the tiller bearing setup. It's much like a bicycle and it is a wear point. What I need to know is how to tighten it. The threaded tube has a keyway, and there is a finger tightener. How much leaway is there to tighten? I have a brand new go-go that the tiller keeps getting loose. An easy fix, but I guess I'll have to take it in or void the warranty. They should have put red loctite on at the factory. The nuts on the motor mount are "nylock" nuts. Self locking. Other than that, thank you for making this video. It's best to know ones machine. Tech or not.

[@MobilityDirect]

You are right, we should have continued to break it down all the way, we'll do another one soon with a newer model and not stop short. :) Thank you for watching!

[@josedomiinguez4496]

👍👍

[@MobilityDirect]

Thanks for watching our video, Jose! We really appreciate the support.

[@josedomiinguez4496]

@@MobilityDirect ok

[@cesarbolivarortiz1524]

Saludos,,, necesito el diagrama del motor,,, lo desarme y no logro armarlo

[@MobilityDirect]

Saludos!

[@miltongood9160]

Are sure that you are using a correct screw driver ? a pozi drive [tappered] will strip a torqu or paralel cross head screw!

[@MobilityDirect]

Thanks Milton!

[@esneydercubillos8820]

Por favor si se pudiera traducir al español gracias

[@MobilityDirect]

Hmmm puedemos pero, no tan pronto.

[@oldflorida2003]

System tech

[@mellieaqua6954]

I need someone to either charge my battery for me or the address n phone number of companies that can fully charge the 7 year old battery so i can take scooter out again

[@MobilityDirect]

If you have traditional let acid batteries. They only last for about 2 to 3 years. After that you need to replace them. You have lithium batteries. That's another story they can last up to 11 years

[@dawneedotcom]

Why doesn't my scooter slow down or speed up??

[@dawneedotcom]

My gogo button won't let it adjust the speed any help?

[@MobilityDirect]

kzbin.info/www/bejne/i5Kbd4Ofi8p4g6s

[@shirleyfinch6305]

my go go ultra has 9 beeps can you point me in the direction what to look for ?

[@MobilityDirect]

Check out this post we made about this exact topic: www.mobilityscootersdirect.com/forum/knowledge-base/pride-mobility-go-go-scooter-beep-9-times/#:~:text=If%20your%20Pride%20Mobility%20Go,be%20in%20overheat%20protective%20mode.