How to Replace Galaxy S5 Screen | Complete Tutorial

[@collingebhardt3098]

Just (fairly effortlessly) replaced my screen with the help of your guide. I've never before attempted a repair on any smart phone. Thanks for the money you saved me and the learning experience!

[@SpartanBeta312]

thank you for this, i used my heater to warm my phone and did it , have no experience repairing phones whatsoever but with patience i did it, saved me 80 bucks

[@GoCellPhoneRepair]

@Naomi Armitage At the time there wasn't any pre-cut available. Now the part usually comes with pre-installed adhesive. When it doesn't we use the pre-cut type that you are talking about.

[@benjamen007]

What temperature did you use to heat the screen? You're using a usual heatgun correct with adjustable temperature? And as always for others, test before installing it.

[@freddykreuger7750]

just did it took me like six minutes but i knew what to do as i watch the video a few times before i even got the part, woldnt of been able to do it without this video thanks dude

[@GoCellPhoneRepair]

@Umar Khan Yes. You can replace the charging port which the cables are attached to.

[@deucedaprodeuca]

+Go Cell Phone Repair After changing my digitizer, the volume rocker stopped working. I then changed the housing to where I know the volume rocker was working, and it still didn't work. Any ideas? I can still control all the volume levels through the screen.

[@revelationteal1146]

is a samsung device still water proof when screen replaced because the liquid the man at delamo mall put on it start discharging but then I used some crazy glue to stop it and my phone working fine with a little like not noticeable dust under the screen but you can't really see it like it's like it's not even there but is it water proof

[@deucedaprodeuca]

Revelation Teal It's not. I changed it and tested it. I had to immediately open it and dry it out. Some would argue that it's human error, but I did as good job as anyone could do. It's luck if it's still waterproof. Also, these phones lose their IP67 certification based time. The temperature fluctuations and age also make the waterproofing components susceptible to failure.

[@GoCellPhoneRepair]

@Ozzie Bogan I'm pretty sure it was 1mm on the edges and much wider for the top and bottom ends. You can always get the wider stuff like 3/8" and cut it to size in for the ends.

[@saintsrowthe10th36]

thanks for the video man, this is the clearest tutorial I could find. Keep up the good work.

[@simulatorlife629]

Thx for the guide!Just fixed my S5 today by using this video.Everything working properly and so easy to do.

[@GoCellPhoneRepair]

Jack hole Cool. Congratulations.

[@headforthehills3353]

Great video. How much does the amoled screen run?

[@NicoleCorby]

Hey! Awesome video. Thank you for sharing. Do you know how i can fix the silver parts around the edges of the phone? Is there even a fix for that? Mine is pretty beat up...

[@GoCellPhoneRepair]

Nicole Corby You can replace the mid frame. The catch is that it's very risky to remove a working screen. They are very easy to damage in the process.

[@MJTechChannel]

Great tutorial!

[@GoCellPhoneRepair]

Thank you.

[@MJTechChannel]

My screen came out in pieces, even tho it had only 2 hair line cracks. This tech did an awesome job taking the old screen almost intact. My wife says I am a "pro" sssshhh, she doesn't know I looked at this video! Lol :)

[@marianomolina263]

Hahaha... lol, Jay! ;-)

[@PartyClatita]

Hey dude! I just finished the replacement screen to my galaxy s5. IT WORKS! THANK YOU FOR THE GREAT TUTORIAL!

[@GoCellPhoneRepair]

Cool. Congrats.

[@PartyClatita]

2 days after, broked.

[@SnowfeetUS]

RIP

[@alexdavis45]

What tape did you use, was it the 1mm, 2mm or 12mm?

[@VirtuaViolenceGaming]

Followed this to fix my phone! Great guide thank you so much man! :)

[@shabazqureshi160]

how well does the adhesive work? Is the phone still lifted afterwards?

[@GoCellPhoneRepair]

Usually it works fine but once in a while I have had to add some at the bottom end.

[@wildanfirdaus8009]

is the lcd type of all variants of samsung galaxy s5 just the same? so it's like just plug and play system whatsoever. or each country has it differently? please answer thank you very much

[@SunnySingh-yl3mh]

hi if you don't have that gold foil goes behind LCD would it effect LCD in anyway over heating or something else

[@GoCellPhoneRepair]

I have not tested it that way to determine what effect it will have nor am I sure whether that acts as an insulator or actually serves the anode function of the AMOLED. I suspect it is the former and not the latter. Small tears don't seem to be a problem as long as you smooth them out. Beyond that, I don't have an answer for you. Hopefully someone else here does.

[@GoCellPhoneRepair]

@Agastya Harta Is it still under warranty? If there is no sign of physical damage maybe Samsung will repair it for you. If it is the AMOLED they are down to about $150 in the US now. I would think that price would not be too different in Indonesia.

[@nancypark8910]

Is the replacement screen in the description an OEM part?

[@GoCellPhoneRepair]

nancy park High Nancy. The AMOLED is always OEM. The glass may or may not be. We have found the durability of after market glass to be comparable to the OEM one.

[@cheezybread7783]

Better order it from Aliexpress or Badongg

[@Jerudrums]

Hi. So I need to transfer a working lcd screen from one phone to another. Do you think its do-able without breaking the LCD?

[@GoCellPhoneRepair]

+Jeru Andrews Do-able but not what I would call easy. There's a video around here somewhere. You have to be very very careful as the AMOLED is super fragile and the cables are easy to cut through if you aren't careful. While I don't advise it good luck if you decide to give it a try.

[@andrewwood4165]

Hi great vid, When removing the screen all the foil on the back of the amoled came away, Do i need to replace this foil? What is it for?

[@GoCellPhoneRepair]

I believe that is has something to do with regulating voltage output to the AMOLED. If you piece it back together it should work okay. If I can find a more definite answer I will post it here later.

[@andrewwood4165]

Hi, thanks i managed to purchase a replacement.

[@quadzillafpv1123]

i was wondering first. is there something close to the ruberized tacky tape that is original on the glass holding the glass and lcd to the frame. I cant find anything close to original and second do you recommend wire or playing card to remove the glass. ive done both and never broke with card but i want your opinion

[@GoCellPhoneRepair]

+john barry Search for pre cut Galaxy S5 adhesive. There is some that is very close to the original. gocellphonerepair.com/how-t/galaxy-s5-replacement-parts/

[@Gera2289]

do you have a video on how to replace a lg stylo screen?

[@andyperkins7226]

Did you not plug the flex cable for the button back in? Or do you not need to? It just looks like it's stuck to the foil to the replacement screen. Thanks in advance

[@GoCellPhoneRepair]

Yes definitely need to plug that back in. I think he was off camera at that point. I will make an updated version soon.

[@gyunagyos]

Hey! Can u recommend some sort of adhesive for S5 to make the phone water resistant again? Thanks in advance.

[@GoCellPhoneRepair]

+gyunagyos Outside of using the pre-cut adhesive your best bet to waterproof- I should say make water resistant- is probably getting a Liquipel treatment. Id advise against using any type of glue as that usually results in either seeping into the phone and causing damage, not applying enough to entirely coat the surfaces, or in the worse case melting plastic parts- Krazy glue can do this. If you are set on using glue something like B-7000 _might_ work but again thats not something that I would recommend. Great avatar BTW.

[@gyunagyos]

+Go Cell Phone Repair Thanks a lot for your answer. Unfortunatelly Liquipel is only available in US, but I'm in EU. I don't want to mess up my phone so I'm not going to use any super glue as u said. I already ordered the pre-cut adhesive what I saw on your site, and maybe I will order some red tape too just to make sure the screen is nicely fitted because now i fixed the screen with this type of adhesive, but its not storng enough. ( www.ebay.com/itm/Pre-Cut-Adhesive-Sticker-Glue-Tape-Screen-For-Samsung-Galaxy-S5-i9600-G900-Hot-/172104620635?hash=item28123c1a5b:g:5h0AAOSwG-1Ww-MD ) Looks like I have to say goodbe to my waterproof S5 :( .

[@gyunagyos]

Hey! The adhesive arrived. What do u recommend for the applying? First place it onto the frame than insert the screen or reverse, first install the adhesive to the screen then insert it to the frame. I have red tape too. Do you have any further tips for the best possible installation? Thanks in advance.

[@GoCellPhoneRepair]

I like to apply it to the frame but I suppose that is subjective. Heres how it works on the S4 kzbin.info/www/bejne/ep_MfHSGhNCFeZo

[@gyunagyos]

+Go Cell Phone Repair Thanks a lot! Your videos are really helpful :) I repaired my phone but after this repair the two bottom capacitive touch buttons became extra super sensitive I always touch them accidentally when pressing the home button or scan my fingerprint. Do you have idea what I messed up? Maybe some grounding things or I don't know :( Thanks a lot for your help.

[@mthlay15]

What's the temperature ceiling of the AMOLED? I have a infrared thermometer and a heat gun. I would like the glass to separate easily but without damage to the AMOLED screen?

[@MegaCrosscountry1]

When you pore the glue dose it affect the front view camera, because I could see that in that specific part it's clear and dose not have any glue on it.

[@GoCellPhoneRepair]

Glue? You mean adhesive? If you add any it should not cover the camera or proximity sensor windows.

[@MegaCrosscountry1]

So then when it's being add it dose not affect the camera, my phone is jut broke on mainly at the bottom. Smaller debre is where the home button is.

[@GoCellPhoneRepair]

jose meza No it should not affect the camera as long as you don't put adhesive over the window that the camera sees through.

[@davesecx]

Does the gold foil on the back of the LCD actual matter? If I rip the foil, can the LCD still be reused?

[@alensehovic2685]

Is that phone waterproof after service. I have the same.

[@TheAlienilluminati]

I accidentally ripped the tiny wire for the back button. I imagine I can get it back together if I take the time to do it, but I'd rather replace it. In the case that I can't, can that part be ordered? **UPDATE** Never mind. I scrolled down and see that someone else had the same question I did, and then I saw your reply. Thank you for replying to comments. I took my display off after watching someone elses video and no other video made mention of those cables, so yours is very helpful. If only I saw this one first.

[@dchosendamian1028]

Can the G900A mainboard be replaced in a S5-G900T phone.

[@ifartinelevators]

What was the tape used?

[@DElionel1995]

I accidentli cut the back and multitask butten is then only the lightning that is not going to work or the butten themself? and also is there a remplencement part for that?

[@GoCellPhoneRepair]

***** Yes you can replace the whole charging port and that's attached to the menu and back buttons. Each carrier has a different one though so you have to make sure to buy the one for your exact model.

[@rmelz3456]

I'm about to put on the display, could I add no adhesive tape to the physical buttons that sticks to the screen? Because it already sticks to the frame of the phone. I only have an adhesive frame for my screen and the screen already has adhesive like yours. Thanks in advance.

[@GoCellPhoneRepair]

You want the buttons to stick to the screen otherwise they won't be as sensitive. I try to get by with the old adhesive if it's still sticky but if not you may have some problems.

[@rmelz3456]

Go Cell Phone Repair What type of red tape did you use? 1mm or 2mm? Oh can I also use a 3M Double Sided Adhesive Tape - 2mm instead of red tape?

[@rmelz3456]

Go Cell Phone Repair If you used two types of red tape, I'm just going to ask what type of red tape did you use for the physical buttons only. I already have a Pre-cut adhesive glue double sided tape for my S5.

[@cesarhfborges]

this procedure return possibility for water proof ???

[@tngustavo]

I'm not sure if putting those adhesive between screen copper thin plate and phone mid frame would be a good ideia, as it could reduce the heat transmission. The screen is one of the most important heatsink of a cell phone.

[@xavierescalante82]

what kind of heat gun you use? and temperature?

[@GoCellPhoneRepair]

Xavier Escalante In this video I'm using a Drillmaster from Harbor Freight. I also have a Wagner that I like but it's not as powerful. I suggest heating slowly from a distance up to the point where it is almost too hot to touch.

[@brandonbias1079]

where can i buy the screw set in the US?

[@AgastyaHarta]

So this afternoon i went downstairs to get my phone and when i unlocked it it does nothing completely black nothing would come on unless the sound and the notification led. my friend told me that the lcd was completely damage. And the cost of repair is not that cheap. It costs almost 200 USD (converted from rupiah) here in Indonesia. Do you think i should go on with the repair or sloud i replace the lcd by myself ? Thanks

[@JAYRAY00]

6:20 - "just being really careful not to damage anything", 10 seconds later he gouges the tool straight through the home button seal! :-0

[@chrisjones195]

Hi In need of help, I replaced the screen on my S5 and the speaker does not work now. Have taken apart and replaced the speaker but still does not work. I am looking at replacing the daughterboard, as the speaker attaches to it. Is this a waste of time and any ideas what to try next? Thanks in advance

[@johnTaylor9760]

So I have dropped my phone a few times and the silver lining around it kind of banged up is there an installation video in your catalog that deals with that subject mater? Thanks

[@GoCellPhoneRepair]

John Taylor Not yet. The most difficult part of that repair is getting the display off without damaging it. If I come across one I will definitely record it for upload.

[@johnTaylor9760]

Thank you!

[@NithyavathiVenkatesan]

Where can i buy the top screen, back camera screen and glue? any advice and help please....

[@kingkhanv2]

the buttons near the home button i kind of accidently ripped the black cable, is there any way this cable can be replaced

[@Blade0427]

Were is the best place to get the double stick tape?

[@GoCellPhoneRepair]

About halfway down on this page gocellphonerepair.com/how-t/videos/galaxy-s5-screen-replacement/

[@OrlandoHelena]

can anyone please tell me which type of tape he is using ? thank you.

[@freddykreuger7750]

going to have a go at this one seems a bit harder than but i have fixed the s4 and it was simple enough this operation seems a bit fiddly but patience and being careful will do the trick.

[@shadowtuy]

I am a tech for a cellphone repair shop and i have been having issues and need advice. I have been repairing phones for years and the only one to give me issues is the galaxy s5. The problem is the adhesive, no matter how its applied it wont hold for longer than a few days...I bought a phone from my boss that I built from broken galaxy phones. My I just noticed my screen is letting go. So I was curious to what tape or gluing method you use to do this model of phone...I have tried your pre cut adhesive, but on this phone it had no change except for how long it held for.

[@GoCellPhoneRepair]

shadowtuy Do your replacement screens come with adhesive? If not get the pre-cut sheets shown on this page. gocellphonerepair.com/S5 It really makes a big difference for this phone, the Note 4, and the Mega. I had the same problem you did until I stopped trying to cut my own.

[@shadowtuy]

Thanks for the reply!! I have used the pre-cut and still didn't hold ...I even tried adding some extra hand cut adhesive in the weak areas....no dice. What I think the problem is the phone is rebuilt from parts and the external chassis was from a trade in that was slammed in a car door..Sounds stupid yes but, it looked flat when i replaced the busted components. So I'm going to break it down and use the parts that still have use..

[@fattyspecial]

Question for you... Are there necessarily any telltale signs that an S5 has had its AMOLED replaced? I am sending my phone back to try to get warranty repairs after having a non authorized samsung dealer replace my AMOLED. Is there any chance in your opinion that they won't know the screen has been replaced? Does it depend on the adhesive used? thanks

[@GoCellPhoneRepair]

I haven't heard from anyone who tried yet but yes I suspect that use of the proper adhesive would be a factor. We use a single piece now that looks a lot like the original but I'm sure that it's made by a third party. There might be other signs on the inside depending on how the repair was done.

[@Adnankussad]

From the website you provided, there were 2 products from the end which seemed similar, to be specific, the {US OEM New Samsung Galaxy S5 G900A G900T G900V G900P LCD Screen Touch Digitizer} and the {Samsung Galaxy S5 i9600 G900F G900H G900M G9001 G900R LCD Screen Touch Digitizer} i just want to know the difference between them, and will each of them affect the phone differently, or will both have the same effect on the phone?

[@GoCellPhoneRepair]

To the best of my knowledge all S5 displays are the same. I believe that they are listed separately with different model numbers for cataloging purposes but if you have any concerns feel free to message the seller to confirm compatibility.

[@Adnankussad]

Go Cell Phone Repair But eventually both will fix the phone well, right?

[@Adnankussad]

Go Cell Phone Repair Plus, which model do you prefer from the ones i mentioned above? Because trust me, i payed loads for this phone, and i wont simply accept for it to be fixed by parts which aren't guaranteed or may be easily damaged.. I prefer parts which are certified and could be used to fix the phone like good as new.. So from your experience, which one is preferred?

[@robochomp]

First, great video! I followed this guide and everything seemed to go pretty smooth but now my phone won't charge. After I buttoned everything back up, the phone turned on just fine and the screen displayed just fine (confirmed all buttons worked too) so I plugged it in. I then noticed that it would not charge and it eventually died. Now I cannot get it to charge enough to restart the phone. It will start to charge for a moment and then "reboot" it's charge screen animation; it repeats this every 5-6 seconds or so. Is it possible/likely that I may have damaged the charging port ribbon while removing the screen? The sticky area around the back/home buttons has a few tiny pieces of the old frame in it; could that be causing a short? Does the AMOLED have anything to do with charging the battery or is it all through the charging port ribbon? Any help or suggestions would be greatly appreciated.

[@GoCellPhoneRepair]

robochomp I would suspect a problem with the charging port. That said there have been several people experiencing similar problems or power button issues while being highly confident that they did the repair correctly. I'm not sure what is going wrong but I'd like to get a hold of one that failed and try to figure it out.

[@robochomp]

Go Cell Phone Repair This is the first time I have ever attempted any sort of cell phone repair and so it is very possible that I screwed something up along the way. I am going to go ahead and order a new charging port ribbon and hopefully that fixes it. Thanks a lot for the feedback!

[@daveng5659]

Is it possible to change the lcd screen without replacing/removing the glass?

[@GoCellPhoneRepair]

+Dave Ng Possible but not really worthwhile. The AMOLED is what you pay for. The cost of the class is minor in comparison.

[@kimifb1871]

Hi, I just want to ask something because I'm not quite sure if the screen is the real problem but I can no longer open my s5 the screen displa only doted colors but before even though I'm not using the keyboard it always shows up and black white lines either on top or right side of my screen until such time whenever I re start my phone only doted colors are on the screen.

[@GoCellPhoneRepair]

Kimberly Fabio Sounds like it's either damaged or not connected properly.

[@sunbeh]

Do i have to unscrew the 3 small screws in the back?

[@sunbeh]

I just completed the repair, and the answer is no you do not. Since this was my first time with repairing devices, YOU CAN NEVER PUT TOO MUCH TAPE, PUT THAT STUFF EVERYWHERE ALSO BE CAREFUL WHEN INITIALLY REMOVING THE SCREEN, THE WIRES AT THE BOTTOM ARE *VERY* FRAGILE, AND IF RIPPED, THE BUTTON ON THE BOTTOM WILL NOT WORK. Thanks, guide helped out a lot!

[@Denny1000000]

will it be waterproof after replacing the LCD?

[@GoCellPhoneRepair]

Denny1000000 In my opinion once you crack the screen it will never be as water resistant as it was when new. Using the pre-cut adhesive will help you retain as much of your IP rating as possible if installed correctly.

[@Ktav95]

Go Cell Phone Repair what does Denny mean? if water goes inside the crack of LCD?? confused

[@sparticus214]

Denny1000000 hell no

[@cheezybread7783]

Nah that depends on how u seal the phone display with the phone ..... Mostly there will space where water could again damage it

[@Adnankussad]

Just a question please, after the screen repair, wont there be any gaps at the edges of the screen which may let the water go inside the phone and damage it? How could this problem be solved? Please help, because I've recently fixed my phone and I can notice that some light is coming out of the edges of the screen, and I'm seriously not ready to re fix it again from water damage..

[@GoCellPhoneRepair]

While it is improbable that the phone will be as watertight as it was when you got it there should not be any light leaking through the edges. Where did you get the replacement screen? If it is seated properly then I would be concerned about the adhesive between the glass and digitizer. Otherwise if you are having trouble keeping it stuck down because of the water that leaked through before the repair you will probably need to replace the adhesive. You'll have to be very careful if you remove the screen as you can potentially break it in the process. The orange stuff on this page is the strongest tape that I know of gocellphonerepair.com/double-sided-adhesive-tape/

[@sethrichardson4528]

@Go Cell Phone Repair. I replaced only the headphone Jack but now the touch screen isnt responding at all. Phone turns on and off and home button works. Is there anything I might be doing wrong or something I can try to do to fix it.

[@GoCellPhoneRepair]

+Seth Richardson Is it possible that the screen is not properly connected? Its no fun and always risky to open these but thats probably what youll have to do. Hopefully there wasnt any damage to the touchscreen flex cable as that might also cause what you described.

[@sethrichardson4528]

+Go Cell Phone Repair yes thats what happened. I saw a small tear in it from open in it I guess. I ordered another digitizer.

[@Blazing_Hamster]

Just curious but would I be able to get a 2k screen for my s5 to replace my 1920x1080?

[@GoCellPhoneRepair]

Not that I know of.

[@biancaorozco1186]

I had my Lcd repaired but the screen keeps popping off on the top right corner, took to the shop again snd its once doing the same, any Ideas. drives me nuts!!

[@utkarsh007]

+Bianca Lopez Same issue with me!

[@biancaorozco1186]

Its annoying having to step back into the shop!

[@GoCellPhoneRepair]

+Bianca Lopez This model can be a pain sometimes. Cleaning and priming the surface before applying a high quality adhesive helps but even then it seems like sometimes they just dont want to stick. Unfortunately you have to take it back until they can get it to stay.

[@crzprgrmmr]

Thanks, just did it with success! Did not succeed taking glass and lcd in one go, as lcd was already shattered and kept bending... Also, I think the screws does not have to be removed at all- they are nowhere attached to the screen.

[@YOPHILLYYO]

Hi, I have a s5 gold model g900h. In the vid you talk about AMOLED but the link only sells LCD digatizers. Do they not sell the AMOLED ? I see ebay has a lot of LCDs takebn off original samsungs s5s,but no AMOLED's also. And the link you posted is in Hong Kong, I thought maybe you sold them. Can you tell me do I just buy a LCD digitizer? And will any of them work for my model ? I tired to comment on your fb page but I can't find a comment box for visitors although I do see visitor comments. I'm trying to order today, hopefully you have a few minutes to reply. I'd appreciate it !! Thank you !

[@GoCellPhoneRepair]

+YOPHILLYYO LCD is a loose term often misused in this business I suspect with the intention of making things clear to the user who may not understand "AMOLED" There are no LCDs for this model so what you see advertised as "LCD" is almost 100% guaranteed to be an OEM Samsung AMOLED since there are no aftermarket displays. They have usually been fitted with an aftermarket glass though.

[@YOPHILLYYO]

Thank you ! I appreciate you clearing that up for me and for the fast reply !!!

[@YOPHILLYYO]

+Go Cell Phone Repair Hiello,Quick question. I got my lcd today and I installed it. But I didn't put it down with the adhesive yet. I broke one of the bottom tabs off for the lighted back button. Would you happen to have a video to replace that tab? If not would you be able to tell me the name of the tab so I can try to find a video and the part ? Thank you

[@GoCellPhoneRepair]

If you are talking about the black flap that wraps around from the bottom it it connected to the charging port. You have to replace the whole thing if you want that button to work.

[@YOPHILLYYO]

+Go Cell Phone Repair In your video about 4:45 to 5:10 those tabs the guy is using the pry tool to remove from the glass. I ripped one off. I found a break down video of the entire phone. Not sure its worth breaking it down cause it looks like I have to take the rest off from the frame. Let me know if its a can of worms. I don't wanna ruin my phone for a lighted tab. I can do without if its a pain in the ass to repair. Thanks

[@andrebryant8159]

how much do a LCD screen cost and where can I get it from?

[@shargil979]

hallo man i have a samsung s5 i did replace the glass and thery was dust on the lens i clean that off with micro fiber cloth and now i put evry thing on and now the camera is blury take pics all are not clear what can i do to clean the senser with..... no focus more !

[@danielmarter5064]

Can I use the screen + amoled display from my sm g900v (Verizon Galaxy S5) to replace the cracked screen on my sm g900a (AT&T Galaxy S5) without any hardware issues? Are the two compatible?

[@GoCellPhoneRepair]

Student Oflife Yes. The screens are all the same.

[@chellmcwags6229]

I have a thin horizontal pink line on my screen. would this mean my LCD would need replaced?

[@GoCellPhoneRepair]

Chell McWags Most likely yes. It's very difficult to remove the screen without damaging it but of you can try reconnecting it first before you get another one. If there is any possibility of liquid damage that could cause what you describe also.

[@chellmcwags6229]

No liquid damage. I've only had it for 3 weeks. Never dropped or anything. I tried to send it to samsung which they wont fix because they said it was rooted. I don't even have a clue how to do that. I bought it outright from rent a center so the manager told me to call him when I get it back. How do you check to make sure its plugged in right. And thank you soo much for responding! I really appreciate it! :)

[@GoCellPhoneRepair]

Chell McWags I see. Well with all that in mind I would try taking it back to where you bought it. Hopefully the manager there can help you. Let him know that because the phone had been rooted when you bought it from him the Samsung warranty is now void. Otherwise you'll most likely have to replace the screen and as of today they run about $140. If they determine that physical damage caused the problem you'll probably be in the same situation.

[@chellmcwags6229]

So I just got the phone back today from samsung and I turn it on and no pink line! So weird! They said they didn't do anything to do but my screen protector is missing too. Maybe it was a loose connector. Do you think it will show up again?

[@chellmcwags6229]

I also checked if I was rooted with two different apps and both said I was not rooted. So I have no idea what samsung is talking about. This is very frustrating!

[@chinmayarolkar635]

My touch is working perfectly, outer glass is fine too. But the display is completely blacked out. So do I need to buy the whole LCD + Glass + Digitizer or just the LCD? Please help.

[@GoCellPhoneRepair]

They are all one piece so if it is damaged then yes you need the whole thing.

[@Illeina_d]

Hello, my phone recently started bleeding after i dropped it, the bottom left corner of the screen is cracked, black is coming out from it and spots of purple that appearing all over the screen. There is also a straight green vertical line which is something to do with the pixels/affecting the screen? I am wondering if a screen repair like this is able to fix a bleeding screen. The touch screen works, i can take calls and its currently still responsive. The purple seems to be getting worse over time and I am wondering if this will continue? If so could you possibly link me to the parts necessary for this. Thank you so much for reading this, have a good day.

[@GoCellPhoneRepair]

Yeah that happens a lot with AMOLED. It will most likely get worse until you can't see anything. A new screen should fix the problem but you can always get one and plug it in first before sticking it down with adhesive just to be sure. When you remove the old one it will most likely break by the way. Parts can be found here: gocellphonerepair.com/S5

[@Illeina_d]

Hello and thank you for the reply, but I live in Australia and it doesn't seem like it can be shipped over here. We can try to arrange a compromise as I am willing to pay for a small shipping fee. Otherwise I'm looking towards buying a second hand s5 for around the 160-200$ price range.

[@ucsmfu]

Behind the class screen, If the copper foil and the black line around the copper foil rips, does it cause the screen to be unresponsive ?

[@GoCellPhoneRepair]

+Enoch Yiu Ive had small tears before that didnt seem to cause a problem but Im sure theres a point where it might cause one.

[@ucsmfu]

Does that mean I need to change to a new LCD digitizer screen ? Thanks

[@GoCellPhoneRepair]

+Enoch Yiu Most likely but it is possible that something else is causing the problem. I would try a hard reset first after youve backed up your data. If that doesnt work then the screen will have to be removed so that you can test a new one just to diagnose the problem/access the logic board to check for physical damage.

[@amandapethel6285]

hello I have a question on wetter this will work for my phone or not. the screen does not appear cracked or damaged but the screen gets really digital and jumps around or gets frozen. or refuses to light up when taping the home or power button. the bottom buttons won't light up either when the screen won't come on. but my notification light will still work. is this worth trying to fix?

[@GoCellPhoneRepair]

I wish it was an easy yes or no answer but depending on what's causing your problem a new screen may or may not help. The only way to know for sure i to connect a good one to your phone or plug your screen into a different phone and test it.

[@sparticus214]

amanda pethel first I would learn to spell whether 😎

[@sexydude14k]

What kinda of tape do you use?

[@GoCellPhoneRepair]

Gates Conrad McClinchie The pre-cut type on this page is the best gocellphonerepair.com/S5

[@sexydude14k]

I want to kbow the kind that you show in your video. If you don't mind.

[@GoCellPhoneRepair]

Oh yeah for sure. It's the Red Tape shown at the bottom of this page gocellphonerepair.com/double-sided-adhesive-tape/ Very sticky and comes in different widths.

[@sexydude14k]

+Go Cell Phone Repair what width did you use in the video?

[@GoCellPhoneRepair]

1mm on the edges and 3/4" under the display. The remainder was cut to size probably from a 3 or 4mm roll. I don't remember exactly on that part but either should work. You can also use the 3M type on the same page and cut it to size but the red tape holds better.

[@rustyplays1810]

Hello, recently my phone has started to flicker green everytime I turn down the brightness and I am not sure if it is the LCD or the new update that came out a couple months ago, but I was hoping if you had any answers for this problem, I would really appreciate that.

[@GoCellPhoneRepair]

I haven't seen that happen but it's possible. Usually, though it's a display on its way out or liquid damage. If it is the screen you'll know soon as they tend to get progressively worse.

[@rustyplays1810]

+Go Cell Phone Repair Okay, also it has started to flicker green when I turn it on and off. Do you suggest changing the screen before it gets bad.

[@GoCellPhoneRepair]

That's where it gets more complicated. If you remove the screen you take a big risk of breaking it in the process. So if it isn't the screen you will probably end up wasting money on another one. All things being equal if unless you think that the phone got wet on the inside I would wait and see if it gets worse. Liquid damage is common with this model since people think it's waterproof and take unnecessary risks with it. If you think that this happened after impact from a drop then it is most likely the screen. As for the software upgrade, that one I can't really comment on as it has never happened to anyone that I am aware of.

[@rustyplays1810]

+Go Cell Phone Repair Okay, I think I am just going to take it to my service provider to see what they think is the best option to do.

[@armigeddon4451]

does the finger print scanner still work

[@GoCellPhoneRepair]

+creamyFox Yes. Even if you replace it the scanner will work. They do not use a secure enclave in the home button like iPhones.

[@armigeddon4451]

+Go Cell Phone Repair thank you very much :D

[@ghalianayef5070]

can i use blow dryer t heat phone or put it ontop of flat stove?

[@GoCellPhoneRepair]

+Ghalia Nayef Blow dryer yes but it will take much longer to get warm enough.

[@ghalianayef5070]

gotchu

[@julioperez3609]

I removed my screen without taking out screws will anything bad happen once i install screen or what was purpose of taking out screws

[@GoCellPhoneRepair]

Julio Perez As long as you took out the screw that allows your home button to be disconnected then you should be fine.

[@bryan-cv2ew]

Hey just wondering, is the phone still going to be water proof after the digitizer replacement

[@GoCellPhoneRepair]

Water resistant would be a better term. In my opinion once it is opened it will be less so than before. Of course if the screen is cracked then the IP rating has already been compromised.

[@bryan-cv2ew]

So i probably shouldn't dive into my pool and start filming, but I should be fine taking it in the shower with me?

[@GoCellPhoneRepair]

bryan park If it were me I would assume that it is splash proof but your question would probably be better put to Samsung.

[@bryan-cv2ew]

thx for the help, you guys are awesome. Only tech fixing channel that actually responds to quetions!

[@sgaws]

other videos show removal of old adhesive around frame edges.

[@0420monoxide]

does replacing the whole lcd make it so its not water resistant ?

[@GoCellPhoneRepair]

justin kropsch In my opinion yes. So does cracking the display. Thank you for saying "water resistant" because these phones are anything but waterproof to start with.

[@GreenEyesBlueEyes94]

I changed display glass few days ago, because i broke it. Is it still water resistant after repair?

[@GoCellPhoneRepair]

Greeneye94 If you cleaned the surface and applied the pre-cut adhesive it will be close to the original IP rating but once you crack the screen your phone will never be exactly like new again.

[@hodgindaylon]

Hi when I was taking the screen out and put it back together the LCD IS FINE but the home, back, menu, finger print scanner, and touch don't work at all and I was wondering if theres a way to just repair them so I don't have to spend 200$

[@GoCellPhoneRepair]

What's the background- were you replacing the screen? The scanner flex is separate from the back and menu button controls so that's strange. Without knowing all of the details my guess would be a bad connection or moisture damage. A bad charging port can also interfere with these functions.

[@hodgindaylon]

I got the home button to work there was no reason to separate it other then I got a new bezel and I took the screen out and the lcd is fine but the flex is broken under the lcd by the home button

[@utkarsh007]

Will it still be water resistant?

[@PartyClatita]

Not 100%.

[@glaivinorc9159]

my phone works but the screen trickles green when I turn it on and it goes black so I gotta play with it turning on and off until it switches over do I need to replace it

[@robertthehair658]

do i have to have a "heat gun" or will a hair dryer work?

[@robertthehair658]

update, I used an 1800w hair dryer - worked fine..... this was easier than I thought it would be....

[@jessicayante2090]

My galaxy s5 was dropped a couple of days ago and works fine but has a yellow tint to the screen any help ?

[@GoCellPhoneRepair]

A hard reset may be worth a try. If there is no sign of physical damage and you are under warranty it's probably best to take this up with Samsung otherwise. You could try disconnecting the screen but that carries a risk of breaking it in the process since it has to be pried away from the housing to access the displays FFC. Of course the problem is cause by damage from the drop then you'll need a new screen anyways.

[@jessicayante2090]

How do I hard reset ?

[@GoCellPhoneRepair]

Jessica Y I should have said "Factory Reset" since your phone is still working. This will erase everything stored on your phone. www.digitaltrends.com/mobile/factory-reset-galaxy-s5/

[@OMIGHTY1]

Jessica Y Make sure that you're synced with your Google account, so everything is backed up! ;D

[@jessicayante2090]

I got a new phone but ty

[@Moh-rk8vn]

I am having a weird problem after i installed the new lcd it comes on everything works,but after i press the top and bottom of the screen to get adhesive to stick and press the power button on and off the screen doesn't come on the bottom lights come on the phone vibrates so it is on,i took the lcd off put it back on same thing it comes on when lcd is not completely attached to the frame even if you turn it on and off it stays on,but when i press the sides and top and bottom of the screen for it to stick it goes out after pressing the power button,what do you think is causing this.

[@GoCellPhoneRepair]

That's a tough one to answer. It sounds like some sort of grounding issue but hard to say for sure. If I think of or hear about this from someone else I'll post any suggestions that I can come up with.

[@TFGDeuce7]

Is it possible I could just send my phone to you guys? It seems like you really have a good grasp on this. I do not.

[@salexmatei]

Could someone please answer me this? Will any LCD for the Galaxy S5 fit all the models? (I am looking to buy a damaged S5 on eBay and just swap the screen with my broken one...)

[@GoCellPhoneRepair]

The screens are all the same for the S5 series. Just remember that it is *very* easy to damage them during removal. They are super fragile and the flex cables at the top are very thin so you must avoid them when prying. It would be best to remove your broken one first to get an idea of what to expect and as always- perform this procedure at your own risk only if you feel confident about doing it yourself.

[@salexmatei]

Go Cell Phone Repair thank you for the extended reply and concern. I might decide to go with a professional this time, as I have an agitated temper :D thanks again.

[@raykyogrou0358]

will samsung still replace the screen if there are some scratches on the frame? The screen is just black, the phone turns on, the home button, the menu buttons, the volume buttons, the touch screen all work. the screen's just black

[@mktking]

how much does fixing this cost in the USA? thanks

[@GoCellPhoneRepair]

The cost of the part is still about $125 so you can to expect to pay $175 with labor. If your AMOLEd and digitizer are not damaged you might get a small core exchange rebate. Like about $25 or so.

[@BestOfMusixx]

I cut my touch connection.. Does i need a new screen? Or is there a replacment possibility?

[@GoCellPhoneRepair]

+Benedict Haas Short answer is yes you need a new screen. Separating the digitizer from the AMOLED and replacing it is not something that I would attempt without some highly specialized equipment.

[@thugguyuk]

i send my s5 for repairs but the side panels looks mess up and the screen broken i really hope they fix that as well as the screen i thought it all gets change together

[@jonahp7640]

Do I have to get a new lcd if my phone can turn on, but the screen doesn't? Thanks :)

[@GoCellPhoneRepair]

Most likely yes. If it isn't broken now it is very easy to break if you take the phone apart. Are you not covered by warranty?

[@jonahp7640]

Go Cell Phone Repair no I don't have warranty

[@zanghi79]

Emphasis on not getting between the 1. the glass and digitizer should be made a little bit more. You made a small remark but as someone who is doing this for the first time I felt clueless as to which parts I was trying to go between. 2. which part of the copper foil you should be on or which side actually has the adhesive. I am to blame but I went to replace my charging port and now need a digitizer.

[@Spare14All]

+Zanghi Mark hey how did it work out in the end, i hope it is good news? i am about to embark on this mission very soon but am a little confused after reading ur post... am i right to assume there is a glass screen, then digitizer and LCD or whatever it is?..... i thought it was just a touch screen digitizer, then lcd, like it is on my htc.... thanks

[@zanghi79]

No there is actually room for you to get between the glass and digitizer. Once you get the screen lifted it's just hard to tell what side of what your supposed to be on. Just lift the glass and go under the whole thing. The wires may confuse you but they snap out of the attachment fairly easy which you have to do anyway so it's not that big of a deal

[@zanghi79]

Only thing you have to really worry about is the back and home buttons. If you are not replacing them just be gentle

[@schoolfun09]

I got my galaxy s5 wet and it works fibe, the touch, the charge, the sound.. exexcept for the lcd. It work when it wants to or after I click the power button maby times... its not completely waterdamaged because my lcd still works. Just when it wants. Any help????

[@GoCellPhoneRepair]

Have you contacted Samsung? If they can't help you then your phone may need to be cleaned on the inside most likely where the display connects to the main board. The tricky part will be removing the screen without breaking it.

[@MrKirbinio]

I cracked my display but im not sure what happened because when i tried to turn on my phone sound came up but the screen stayed black im not sure if my lcd is bad or i riped some kind of cable when i was trying to remove my display

[@MizPiro]

I got a screen off amazon, and i can feel the haptics working and hear the sounds of it unlocking but i cant see anything? Ive done it step by step theres no way ive done this wrong... could it just be the replacement i bought? Or maybe i yanked something somehow? Pls help

[@GoCellPhoneRepair]

Ew. Most likely a bad connection or a defective part. Hopefully you just didn't plug it in all the way but you have to be very careful taking it off again. If you damage it in the process you probably won't be able to exchange it.

[@blackburnmichelson6189]

Bu i do not have heat gun what can i use else ?

[@nariorudulphval]

can I used hair blower instead to hit up the screen?

[@GoCellPhoneRepair]

Yes but it will take longer.

[@nariorudulphval]

Go Cell Phone Repair thanks

[@alihernandez880]

How long would I need to wait with a blow dryer instead?

[@GoCellPhoneRepair]

Ali Ramirez Until the surface temperature reaches about 90 degrees F.

[@miofudge]

i dropped my s5 last week, and there is a nudge and like a scratch(i dont know what to call it) at plastic side or border of my phone. how can i fix it, at least a remedy for it to appear as it wasnt dropped,

[@Itsalexbaker13]

I don't have a heat gun. Is there anything else I can use?

[@GoCellPhoneRepair]

A hair dryer. But it takes a lot longer to generate enough heat.