Goosky S1 Helicopter Radio Setup in EdgeTX (RadioMaster TX16s Radio)

  Рет қаралды 18,539

Painless360

Painless360

Күн бұрын

Пікірлер
@Painless360
@Painless360 6 ай бұрын
For those asking about how to bind this model, check out the instructions in the manual. Page 20... this video is NOT a replacement for reading the manual. goo-sky.com/DownLoad/127302.html Happy flying
@rambo_flight__ken9791
@rambo_flight__ken9791 Жыл бұрын
Thanks for your straightforward approach. A few minor notes: 1:23 - reverse channels A&R (you said A&E, slide is correct) 3:40 - Flight Modes (I recommend turning all trims off on FM0, since we shouldn’t be using them with the flybarless setup).
@Painless360
@Painless360 Жыл бұрын
Great comments, please make content and share your know-how. The more of us do it, the easier it is for the next pilot.. Happy flying!
@MrDLRu
@MrDLRu Жыл бұрын
This will be my first heli once it gets here...Why no trims with flybarless setup?
@Painless360
@Painless360 Жыл бұрын
Same reason as when using any other flight controller. The FC will see 1500 as no input and if start messing with trims then you get into trouble. Happy flying
@zmanphx
@zmanphx 11 ай бұрын
@@MrDLRu A helicopter must be mechanically setup to be neutral at hands off hover, flybarless or flybar. Like taking your hands of car steering wheel while driving, the car should steer straight. I never used trim.
@kajuta240
@kajuta240 5 ай бұрын
Why reverse the A/R channels? I tried this in the simulator and it doesn't feel like a natural way to pitch at all. I can get over reversed Rudder by focusing on the tail instead of the nose, but Aileron as well? Please explain.
@cyberalex4life
@cyberalex4life 9 ай бұрын
Mulțumim!
@stran92129
@stran92129 6 ай бұрын
for those asking on binding, press bind on radio and press the bind button on the s1 located on the right hand side three times. i was also stuck as this step was passed over.
@Painless360
@Painless360 6 ай бұрын
All covered on page 5 of the manual... www.goo-sky.com/DownLoad/95449.html?a=download
@soy_leche
@soy_leche Жыл бұрын
Great timing but any chance you'd do this with the Boxer or the non touch edgeTX? I'm finding some of these thing but others are hidden or I'm missing them.
@Painless360
@Painless360 Жыл бұрын
Which bits are you missing?
@doorknob2012
@doorknob2012 Ай бұрын
I am looking for a way to add the stabilization to a switch and the amount of gain to use. I am tryng to set up a switch to be least aggressive to most aggresive. Thanks for any help.
@Ariautoace
@Ariautoace 8 ай бұрын
Thanks
@Painless360
@Painless360 8 ай бұрын
Thank you!,
@realmotoX
@realmotoX Жыл бұрын
Thanks for the explanation on this video on the radio setup. The one part I was hoping to know is the binding process for the SFHSS. I never used a Futaba radio so I am not familiar with the process. Could you make a part 2 on the binding for the S1? Thanks
@Painless360
@Painless360 Жыл бұрын
I cover that in the videos. Best of luck
@pennylanevideo
@pennylanevideo Жыл бұрын
Just to add, do the frequency tune, if your flying with sfhss futaba protocol, with a TX16s. Mine was dropping out of the sky & very jittery on the sticks. I even had it replaced & it was doing the the same thing. Doing the frequency tune it now flies like dream.
@Painless360
@Painless360 Жыл бұрын
m.kzbin.info/www/bejne/mXeqoaSLgJ6Brqs
@MrDLRu
@MrDLRu Жыл бұрын
Great thanks...What was the tune number?
@Painless360
@Painless360 Жыл бұрын
The number is specific to the individual radio. See video linked above
@Kirtdog
@Kirtdog 5 ай бұрын
Thanks for the setup video. Your throttle curves really tamed this thing down.
@Runk3lsmcdougal
@Runk3lsmcdougal 6 ай бұрын
I used spektrum radio on my s1 with a $20 satellite receiver, all I had to do was load a bnf helicopter template, bind the heli, then change the throttle curve % numbers. Wanted to see the process with radio master aswell tho
@johncgibson4720
@johncgibson4720 11 ай бұрын
Thumbs up. More people should care about small helicopters for their natural high endurance of flight time. I modified my 230s to become a FPV helicopter at 249 grams and HD onboard video recording that flips/dives/snaps with 35 minutes of flight time per charge. No quads under 250 grams can ever beat that, not even professionally designed DJI. They either have to change a battery and going over 250 grams, or they have to turn off HD video and turn off FPV and navigation and make the drone fly in a circle at constant speed to get that advertised 35 minutes per charge, and even then, they can't flip/dive/snap.
@Painless360
@Painless360 11 ай бұрын
Indeed, more blades = more losses. Happy flying!
@IRBry
@IRBry 10 ай бұрын
braaahhh i’ve been trying to find information on that!! i have bigger helicopters as well as yours, any advice? any place i can search and learn more? or just look up fpv drone stuff and strap to helicopter?!
@davidkredow1421
@davidkredow1421 9 ай бұрын
I reset the SF switch and now the red LED is solid and flip the switch it blinks just like it should. Thanks for your help.
@ApappieK
@ApappieK Жыл бұрын
Thanks. This helps a lot for a beginner. The paper manual is much less useful.
@redogg2749
@redogg2749 11 ай бұрын
I have the ELRS version. Can you add a EP2 receiver to the S1.? Or will i need to buy a multiprotocol addon for my trans. Thanks
@Painless360
@Painless360 11 ай бұрын
Most flybarless units have a SBUS input so you can use an ELRS receiver that can be configured for SBUS with it. Watch for CH5 output though with things like SBUS as (at the moment) that is fixed in the SBUS output as a binary channel (high or low only).
@ChrissiRC
@ChrissiRC 4 ай бұрын
Hi, is it a fcc or a lbt version of the radiomaster? Thanks
@Painless360
@Painless360 4 ай бұрын
Shouldn't make a difference... Happy flying
@AlexBongRCFunLand
@AlexBongRCFunLand 10 ай бұрын
I manage to set it up on my TX18S EdgeTX. But I have some issue on setting up it's pitch with the Goosky App as the BT connection kept disconnected after seconds of connected. I hope you can make a complete video on the complete pitch setup on the App?
@Painless360
@Painless360 10 ай бұрын
I'm struggling with the app too. See my comment on that in the video... Happy flying
@AlexBongRCFunLand
@AlexBongRCFunLand 9 ай бұрын
@@Painless360 I managed to set it up using the BT after multiple trying. Found that we need to remove the old recorded BT connection (Everytime!) and do a reconnection for it to successfully connection so that we can proceed with the setting. Now play around with setting to find the best suitable setting for my flying as I found it's very sensitive to the change of RPM or pitch made it easily dropped high during hovering.
@MLeditsofficial
@MLeditsofficial 4 ай бұрын
Can I just bind the heli and fly instead of doing any curves and configuration
@Painless360
@Painless360 4 ай бұрын
Always check the manual if you are not sure... Happy flying
@jhonmariocardenasm6491
@jhonmariocardenasm6491 Ай бұрын
Tengo un goosky S2 con su radio, quisiera configurarlo con el tx16s pero que quede con las mismas configuraciones del radio que viene original del goosky S2, Algun link disponoble por favor
@Painless360
@Painless360 Ай бұрын
I'm not sure I've made a video for the S2... Best of luck
@jj_uk
@jj_uk 10 ай бұрын
How do you set a failsafe when using the Futaba SFHSS receiver?
@Painless360
@Painless360 10 ай бұрын
Check out the docs - www.multi-module.org/using-the-module/protocol-options - I hope that helps.
@waynehuntingford108
@waynehuntingford108 4 ай бұрын
Hello all Heli freaks ... I'm a total beginner and have a omphobby m1 and m1 evo ... I recently bought a Radiomaster tx16s mark ii ... Can I use or program it to fly my omphobby's without extra receivers?
@Painless360
@Painless360 4 ай бұрын
If it's a multiprotocol version of the radio, or you plug in a multiprotocol module into the back. All setup covered in the video
@NoLogic69
@NoLogic69 11 ай бұрын
Great tutorial, very helpful, thank you. How do I set up self level / 3d mode in channel 5. Cheers. 👍
@Painless360
@Painless360 11 ай бұрын
The position of the switch will select it automatically. Use the app and test fly it to check which way round it is.. Best of luck!
@miriamdiggler1288
@miriamdiggler1288 10 ай бұрын
Where do you change the channel mappings? I only find this option in the radio itself, which is a global setting and would then effect every model. Or is my understanding on how that operates incorrect? I would think that you could change the channel mappings per model, but I can't find that location.
@Painless360
@Painless360 10 ай бұрын
You can move the channels in the mixer in EdgeTX for this model... Best of luck
@YuenKenneth
@YuenKenneth 11 ай бұрын
Have any problem or anything need to be care when using TX16S binding? Coz’ I’ve problem and can’t bind Align 150GRS S-FHSS whatever I did😢
@Painless360
@Painless360 11 ай бұрын
I've not got one to try... Best of luck
@YuenKenneth
@YuenKenneth 11 ай бұрын
@@Painless360 so binding S1 nothing special, just set TX16S using SFHSS protocol, that’s all?
@Painless360
@Painless360 11 ай бұрын
Was here.. Happy flying
@bennn1976ify
@bennn1976ify 3 ай бұрын
Thanks for this, just bought an edge tx radio and S1 recently. I'm coming from years of Spektrum and this helped wrap my head around the Edge Tx somewhat. Question though, I'd like to have a "landing" pitch curve on a separate switch from the idle up 3 position switch I use for headspeeds. I'd like to set up the linear pitch curve -100 to 100 to my flight modes but have a switch that overrides the linear and goes to my landing pitch curve like you have your curve set in normal mode. How could I do that? Specifically, on the tx16s I want all 3 positions of SE to have the same pitch curve and have SG up to switch to my landing pitch curve. Thanks
@Painless360
@Painless360 3 ай бұрын
You can assign any switches you want to the different curves. You can setup more than the few shown and use the same method to switch between them. Best of luck!
@henryhartsfield4574
@henryhartsfield4574 9 ай бұрын
Any tutorials for someone who has never set up a tx 16s? I just got it and a goosky S2
@Painless360
@Painless360 9 ай бұрын
Yes, this is a video for those familiar with the radio. See my EdgeTX for beginners playlist.. Happy flying
@matikrk7185
@matikrk7185 9 ай бұрын
Can you solve the problem with sbus? I have a boxer elrs with goosky s1 with elrs lite. I did the configuration as you showed in your video. additionally, I changed the packet rate to 333Hz, Switch Mode to 8ch and other things in lua script also correctly according to the guides, In the receiver options I chose protocol and choose SBUS. finally, when I arm it, the throttle does not work (or it is armed, but it is configured correctly)
@Painless360
@Painless360 9 ай бұрын
Watch out for CH5, depending on the mode it only acts as a binary channel and that doesn't work when the stabiliser wants CH5 to 'do' something..
@DimsimFPV
@DimsimFPV 4 ай бұрын
Hey mate I am new and probs missing somthing I have got it flying but I don’t seem to have negative thr I can fly just not inverted it’s not safe mode or anything like that I was wondering if you have any idea or help ☺️
@Painless360
@Painless360 4 ай бұрын
There isn't negative throttle, only negative pitch. You'll usually a mode with a flat throttle 'curve' and as much negative pitch as positive... best of luck
@j.r.sitman6286
@j.r.sitman6286 3 ай бұрын
I am a subscriber and cannot find a video on how to BIND my S2 to the TX16s. Do you have one? Thanks
@Painless360
@Painless360 3 ай бұрын
I never got my hands on a S2.. Best of luck
@j.r.sitman6286
@j.r.sitman6286 3 ай бұрын
@@Painless360 thanks
@Nico--
@Nico-- 7 ай бұрын
Is your S1 biased towards positive pitch? I set up my TX16s with 2-point pitch curves from -100 to 100 and when I have the stick on my TX16S in the middle, the pitch on the heli is already positive. Overall I have more positive pitch than negative. Is it the same with yours? I saw only one other person mention this in a discord channel. The only way to have neutral pitch in the middle of the stick is to change the pitch settings in the Goosky App drastically. I need to set the middle pitch to the lowest optiont in the app. But this means that my highest possible pitch on the heli has to be lower than it is now. Thanks in advance!
@Painless360
@Painless360 7 ай бұрын
From what I recall, I did look at the blades for zero pitch on the radio and it was neutral. Most setups allow you to tweak the pitch curve on the radio to tweak it to be how you want.. Best of luck!
@eagleonefoxtwo2487
@eagleonefoxtwo2487 10 ай бұрын
Did the stabilisation flight mode work with this settings? I mean the Auto level function?
@Painless360
@Painless360 10 ай бұрын
Yes
@doand1257
@doand1257 10 ай бұрын
@@Painless360 Dear Lee, i am beginner with Heli (not with planes and Quad FPV), do you think this S1 Heli with auto level mode could be a good thing for me ? With this, i will learn step by step
@Painless360
@Painless360 10 ай бұрын
If you can hover a quad in ACRO mode, then a heli like this would be fine. I moved from in stabilised helis to quads and found all of the fine skills with a heli moved over easily.. Best of luck!
@eagleonefoxtwo2487
@eagleonefoxtwo2487 10 ай бұрын
@@doand1257 I have the S1 Legend and S2 Legend now and my level of flying gets better and better..Auto level is very good for beginning and sometimes I switch to normal Mode to learn more normal flying...now I am building a TRex 500L with the fbl system Brain 2 wich have rescue and auto level, too..hope it works like the goosky helis when its setted up. Good luck and give it a try!
@doand1257
@doand1257 10 ай бұрын
@@eagleonefoxtwo2487 Thank you for your reply, I'm plan to buy one but no idea about color, haha
@yakacm
@yakacm 6 ай бұрын
Instead of Goosky making a manual on how to setup for each radio, you'd have thunk they'd just saved a preset. Saying that each time I download something from their site, my browser does it's nut, saying the website is insecure. Don't know what they have to be insecure about, they make great products 🤔
@arthurdelatorre8751
@arthurdelatorre8751 11 ай бұрын
Lee, I set up my curves the same as yours but what I can't figure out is when I add it to my throttle the mix its inverted, on channel 3 with the throttle at the lowest position, the output starts out at 20% and goes to -100 % moving the stick upwards istead of the way I set up the curve to go from -100% to 20% like yours, in fact all the curves are opposit, any idea why this is happening? my radio is a tx16s 2 with edgetx v1.3.3.20 aetr, mode 2 hope you can help! Art
@Painless360
@Painless360 11 ай бұрын
Make sure you've not selected the curves with an exclamation mark in fronI. Best of luck
@Ariautoace
@Ariautoace 9 ай бұрын
I am a returning pilot thanks to Goosky, sorry if I missed it or did not look for it well, is it easy to bind?
@Painless360
@Painless360 9 ай бұрын
All in the video.. Best of luck.
@Ariautoace
@Ariautoace 8 ай бұрын
@@Painless360 Mate, since you have this video, I ordered the same radio as you. I have been watching the video a few times, last question, there is pose-mode where as you know it goes into noobie drone-mode, is that something that is covered here? I understand the rest.
@Ariautoace
@Ariautoace 8 ай бұрын
@@Painless360 You are the first KZbinr I sent a monetary "Thanks", so thank you for your time.
@Painless360
@Painless360 8 ай бұрын
I did something like that with the OMPHobby S2 setup videos, they may be worth a look.. Similar setups.. Best of luck!
@MCsCreations
@MCsCreations Жыл бұрын
Thanks a bunch for the tutorial, Lee! 😃 Looks pretty complicated indeed! 😬 Stay safe there with your family! 🖖😊 And happy holidays!
@remotecontrolledmedia
@remotecontrolledmedia 4 ай бұрын
can I use both versions of the tx16s? 4in1 or elrs
@Painless360
@Painless360 4 ай бұрын
You need a 4IN1 if you Wang to bind to non ExpressLRS receivers... Happy flying!
@BigWillieFPV
@BigWillieFPV 11 ай бұрын
Little heli looks mint, I really want to get my heli on edge Tx, I’d like to update the FW first but every time I try and update EdgeTx I lose all my custom sounds, backgrounds, colours and screen layout etc, I end up going back too my old firmware backup, do you have a way to update to the latest without losing all my settings?
@Painless360
@Painless360 11 ай бұрын
I've not had that here. See edgetx.gitbook.io/edgetx-user-manual/edgetx-user-manual/installing-and-updating-edgetx/update-from-opentx-to-edgetx-1 for the process... Best of luck
@BigWillieFPV
@BigWillieFPV 11 ай бұрын
@@Painless360 thank you I'll follow this and see how I go, very keen for a Goosky S1 👌🏻
@BigWillieFPV
@BigWillieFPV 11 ай бұрын
thank you, it worked this was much easier, @@Painless360
@BigWillieFPV
@BigWillieFPV 5 ай бұрын
Would this setup work the same on a Goosky s2? Thank you
@Painless360
@Painless360 5 ай бұрын
Not sure, I've not had a Goosky S2 here... Happy flying
@kimchristiansen2127
@kimchristiansen2127 Жыл бұрын
hi super cool videos i have seen a lot of your videos i have a completely different question I hope it's ok to ask can i use my radiomaster pocket and bind to my omhobby m2
@Painless360
@Painless360 Жыл бұрын
Check out kzbin.info/www/bejne/iWHaootto9KdhNE best of luck
@nickarganbright7218
@nickarganbright7218 4 ай бұрын
I plan on using this for my goosky s1 and s2, just got it in fact and am waiting for the battery to charge. I am completely new to programming them and was just curious if these settings would work for the s2 also? I can't seem to find any videos on programming the s2.
@Painless360
@Painless360 4 ай бұрын
Beginners Guide to Modern R/C Helicopters (Spring 2022): kzbin.info/aero/PLYsWjANuAm4rpGgQKBXzl9O7L85JeMkzG best of luck
@nickarganbright7218
@nickarganbright7218 4 ай бұрын
@@Painless360 Awesome! Thanks for the reply, I will have to check these videos out tonight. Looks like they will have a lot of helpful info 👍 😀.
@AlexBongRCFunLand
@AlexBongRCFunLand 10 ай бұрын
Thx for the video! I'm using Radiokig TX18S. EdgeTX. on the MIxed ch6 my setting does not have the '!' infront SE for Pi2, is that correct or any issue?
@Painless360
@Painless360 10 ай бұрын
Yes, you need that exclamation mark. It'll be in the list of options, scroll the other direction in the list of switch positions... Best of luck
@johnoseman572
@johnoseman572 11 ай бұрын
Another excellent video, Lee, resulting in me spending more money!🤨 I have been setting up my new heli and am curious as to how you chose your throttle curve settings. Did you convert the values given in the Goosky manual in some way, or are your numbers the result of flight testing? I don't see how you get from 0,55,55,55 in the manual to -100,20,20,20 for example
@Painless360
@Painless360 11 ай бұрын
I'd use the manual settings if you are new to it. I like normal mode to be less aggressive for testing and landing... Happy flying
@peterlatham2407
@peterlatham2407 4 ай бұрын
Thanks for another great video
@eagleonefoxtwo2487
@eagleonefoxtwo2487 11 ай бұрын
Thank you really much...I be thinking to get a radiomaster transmitter for my goosky s1 and s2. But i am german and i find it hard to set it up. Your Videos give a little help!
@scrc511
@scrc511 8 ай бұрын
I have a request my friend. Pls make a video with Blade Infusion 120 bound to TX16S, the setup. It comes with safe, and I know for a fact TX16s can mimic the settings for the Infuson 120. Thank you so much in advance.
@Painless360
@Painless360 8 ай бұрын
If I get one in, I will... Happy flying
@scrc511
@scrc511 8 ай бұрын
@@Painless360 Ok, thanks.
@ricknixon5441
@ricknixon5441 13 күн бұрын
finally figured out a solution. Lots of trial and error. 2.10.5 is different from the version in this video.
@Painless360
@Painless360 13 күн бұрын
Why not share your solution for the benefit of others? Happy flying
@lynsmith1096
@lynsmith1096 Жыл бұрын
Thank you for this tutorial
@h2o40fpv
@h2o40fpv Жыл бұрын
Great video thank you.😊
@yakacm
@yakacm 6 ай бұрын
I was thinking, has the manual changed as it doesn't have anything about the tx16s in it, but I see that's for the S2. The manual definitely isn't a Blade manual, but it's a heck of a lot better than the manual of the tx16s, but you can forgive them that, as most folk who use the tx16s, are going to be ppl who like to get stuck in, and the OS on the radio isn't created by Radiomaster.
Goosky S1 Mini Helicopter: Overview and my thoughts..
11:09
Painless360
Рет қаралды 30 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
Правильный подход к детям
00:18
Beatrise
Рет қаралды 11 МЛН
Goosky S2 how to update to the new firmware version
7:59
Barel Atanelov
Рет қаралды 1 М.
Spektrum RC Safe Modes on the Radiomaster TX16S!
18:19
Shane's DIY
Рет қаралды 19 М.
FrSky ETHOS 1.5.x+ Gyro Gain Mix Setup with Vars (Variables) Feature and Callout New Methods
17:05
Discovering a "Design Flaw" - GOOSKY S1 Review - almost A YEAR of use
10:09
EdgeTX or OpenTX Helicopter Setup & Programming
22:13
Simon Kuskye
Рет қаралды 17 М.
Goosky S1: Bluetooth App Problems and Solutions.
16:46
CHUNKY C's RC ADVENTURES
Рет қаралды 2,4 М.