Govee Pros Install (Black Version) Canyon Lake, Tx

Hey You Tube Family, welcome back for another Govee Pro's Install. In this video, we are doing an install with the black version. Strands were added to the top and bottom. This was a 200ft install but with two separate power adapters and controllers. I wish we could of added more footage to this video but the weather was not holding up well and so delays where a huge factor but the install was a success. Thank you all for your love and support to the channel during these difficult weather changes that effect our installs. You all are awesome!!!
"Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates"
Govee 150 ft Outdoor Permanent Lighting
amzn.to/3swC3Yr
Govee 100 ft Outdoor Permanent Lighting
amzn.to/49yGMcH
Govee 50ft Outdoor Permanent Lighting
amzn.to/3uiVAMk
PRO EDITONS
Govee Pro's 100ft
amzn.to/3MC6hQy
Govee Pro's 200ft
amzn.to/3svjuDZ
Wirefy 150 PCS Solder Seal Wire Connectors
amzn.to/47idT2I
LED Clips
www.amazon.com/dp/B0B2WY1D2F/...
BTF-3 PIn 18 Awg LED Addressable Wire
www.amazon.com/dp/B07SKGTCWQ/...
Ryobi Brad Nail Gun Brushless 18Gauge
www.amazon.com/Ryobi-One-18GA...
1" Brad Nails
www.amazon.com/meite-Length-G...
Heat Gun
www.amazon.com/Wagner-Variabl...
2"x2" Wood Squares
www.amazon.com/gp/product/B07...
Pickle Potion Sport Drinks
www.amazon.com/Bobs-Pickle-Po...
Ryobi Misting Fan
www.amazon.com/RYOBI-18-Volt-...
Cooling Rag
www.amazon.com/Ergodyne-Chill...
Ryobi Glue Gun
www.amazon.com/dp/B0BP9YM9LT/...

[@efthimios]

What a professional install - wish you can do my house in PA

[@jbsdiytv]

Thank you for your comment. I’m confused, I’ve mentioned multiple times on other comments that we would travel to your state. Have you had a chance to look at those? Visit our social platforms at the top so we can start your quote on your install. Thanks

[@watch_your_six]

We are so glad we found you guys on social media. You guys are awesome and went above and beyond. To those watching the video and reading comments, these are the guys you wanna hire. Top notch service and trustworthy. Many thanks to JB and his team!

[@jbsdiytv]

Thank you, it was a pleasure meeting my subscribers and taking care of us during a difficult install with the weather coming from every dang direction. 🙏greatly appreciate the love and support

[@bonniejackson2259]

I couldn't agree more. They are the best.

[@bonniejackson2259]

They do excellent work and have the experience to give you what you want.

[@rj2742]

Been following this page for a bit now. Trying to learn how to do a proper install as I'm located up in MN. Love the videos!

[@TheChardluz]

How much did this project cost

[@user-dk3zt4tl9e]

Hello there, I am a marketing manager at Sikaic, an online furniture store. I've been impressed with the engaging content you create on your KZbin channel. I'd love to work with you on our gaming desk. Please let me know your thoughts so we can move forward to the next steps. Looking forward to hearing from you!

[@bonniejackson2259]

They are absolutely beautiful. Another wonderful job!

[@jbsdiytv]

As a long time client, I greatly appreciate, respect, and value your comment Bonnie. Much love🫶

[@bigmoecortez6362]

Thanks for the heads up. I did a test facing the wall and pointing down. They do look better pointing down. Once again thank you.

[@jbsdiytv]

@bigmoecortez6362 your welcome

[@AB_thingsDFW]

The boss 💪.

[@jbsdiytv]

Thanks bud, we really appreciate it🤝

[@handydadtv]

A+++++ job!

[@jbsdiytv]

Thanks bud, really appreciate the compliment

[@jacksonb03]

JB you have absolutely out done yourself again!!! Dont know how you do it but you do. I have questions but I will wait maybe they will be answered.

[@jbsdiytv]

Thank you 🙏 I just hit record and be myself 😁 please let me know how I can help

[@jacksonb03]

I have a question regarding how to run the cables on my home. I have pictures of what I believe will work but wanted to run it past you. How can I get them to you?@@jbsdiytv

[@jbsdiytv]

Use the links at the top for our social platforms. Reddit and FB messenger I can receive photos

[@theotherones8818]

New subscriber! From the FB Christmas light page. Great work guys.

[@jbsdiytv]

Thank you for watching and your support. Welcome. Let us know if you have any questions

[@SithLordBishop]

All the lenghts are so helpful for planning this thanks! is it 9 or 10 lights per 17ft strand?

[@jbsdiytv]

The pros are 10 lights and the non pros are 12 lights. The pros lights are spaced 18 1/2” apart while the non pros are spaced 15 1/2” apart

[@barberclips4304]

Great job👍. How would you attach Govee pro lights to stucco?

[@jbsdiytv]

I’m not sure how old the house is but drilling is the only way. I mentioned old as possible brittleness. You will need to predrill a small hole small enough for your plastic insert size and then find the correct screw to into that. If your fascia edges is a few inches away from your wall, I suggest just placing them there cause mostly likely that’s wood

[@MMARIC20]

Hey Jb i noticed you did more than two inches from the wall. Probably because its center...do you recommend sticking closer to the wall...2 inshes or center it. From your experience.

[@jbsdiytv]

We stick with 2” for most installs. The only time you may need to adjust is if throughout your install there are areas that have design trim on the wall. Other that, keep it consistent so the appearance of how it shines on the wall

[@bigmoecortez6362]

I have a question for you. Can I install the lights behind the fascia board facing the wall? So the lights can be less visible.

[@jbsdiytv]

The Govee lights are intended to be installed 2-4” from the wall for the cone effect. It is your preference though. Yes they can be installed like you have mentioned but you will get a round spread out light. Not saying it’s not ok but it’s your preference

[@efthimios]

Thanks for your video! I need 200 feet should I order two 100 kits or one 200? Are you really happy with the pros? I was so torn as trimlight quote was $4500 vs $700 pro with $1000 install I’m worried about the install and hope they install the Govee nicely if I go with them

[@jbsdiytv]

It’s difficult to determine what exactly what kit you will need since I don’t have a roofline layout of your home. In a previous comment I mentioned that as an installer, we prefer working with the pros. I’m kinda confused on what you said at the end of your comment stating I hope they install the Govee nicely. Who’s they? Is Trim Light installing your Govee lights?

[@maxin3231]

You are the best! I like your style of installation. I wonder, do you need to have the power from the end of the plug only? Let’s say I have power in the middle of the roof, but you only have one set of lights that will run on both sides. How would you do that ?

[@jbsdiytv]

Hi and thanks for watching. So I’ve had this question brought up to me so don’t mind sharing my thoughts. Some have tried to T- off in both directions. It works but it only mirrors each other. Say you want to do spot lighting… if you turn off some lights on the left then the same will shut off on the right. If you have two controllers and want to split them from the middle out, then your presets will go opposite from each other. Only in advance settings you customize your own and fix the direction of flows, not presets. Best way to fix this is start your lights on the side and if there is attic space, use an extension cord from that outlet in the middle and get to your power adapter with controller on the side. Keep your controller closer to the front of the house so you don’t have any issues connecting

[@bryanmcdowell5786]

Where do you get the extra clips for each light?

[@jfpolymath]

Nice videos. Question. Can you splice in two strands into the first? Say I have a 100ft and at 20ft I want to take one strand on to a lower Eve and the other strand on the upper eve - like a Y. Still the same length and number of lights but split?

[@jbsdiytv]

You can’t do a split Y. The app won’t read those individuals lights as shut off. If you put a split they will react the same and not different. That’s the purpose of the advanced settings

[@paulmaestas8709]

Which Govee outdoor lights are actually better between the Govee RGBIC 1st generation lights and the Govee PRO lights? I plan on using the all white lights mode year-round other than for the holidays. Thanks

[@jbsdiytv]

From an installer standpoint I believe the pros are much easier to work with. The first generation lights were considered DIY friendly but its still is a bit challenging for the average Joe. The first lights have a distinct tent of green/purple in their white looking from different angles as for the pros, you get the best consistent cool white and warm white as it uses its own LEDs to make white. Pros are best because they match typical landscape lighting. To others, the white doesn’t matter, in your case it does cause you mentioned all year round and that’s best know for security lighting

[@ApogeeLLC2012]

Thank you for your video. I'm in Idaho. I contacted Govee a few days ago to inquire about the black 200' release date. They said Nov 12th, but it actually came back in stock today. They said that the driver module is included in the 200' kit. Can you explain how/what/why a driver module is necessary? I have 400' to install. Also, I'm adhering to metal soffit... any advice on an adhesive to use in the event the 3M fails? I might start with it to avoid an unwanted ladder climb after the snow falls. Thanks in advance!

[@jbsdiytv]

They are back in stock. Yes, indicated on their website the module driver is needed after a 150ft. If you decide to add 50ft extra from another box, it helps drive the data better to the remaining 50ft. So thats what it says on the govee site. Now I have installed 200ft without it since the module driver was never in the 100ft to begin with but the app read 12 segments without any issues.

[@reckle720]

How do secure the lights what clips do use with your nail gun

[@jbsdiytv]

Govee/AliExpress-Endless amount of clips #diy #howto #fyp #govee kzbin.infoiwZyyI3RXUw?feature=share Take a look at this video on where we purchase our clips. Amazon usually sales out quick

[@dancevids23]

I have 2 100ft govee pro outdoors. Since the initial release did not come with LED module driver, can I have one govee plug on the left side of the house and the other 100ft on the right side but have the Govee app sync in one direction? Like if I want to do a color change from right to left, would they end up converging instead of the combined 200ft left -> right effect?

[@jbsdiytv]

Currently you can run 200ft on one controller. Now I’m not sure whether or not they will update the firmware so that isn’t possible anymore but it currently is. You can add 12 strands together

[@ashvinpawar1891]

Cost for installation of 150 feet Govee pro black? I live in Cypress,Texas.

[@7D9Z28]

Great work! How far off the house did you go with the soffits? The peak looks like 8 to 10 inches?

[@jbsdiytv]

Hi and thanks for watching. This install was 4” off the wall

[@RushPL1]

Nice one. We did an installation with JB's team (not this one) and can absolutely recommend the crew. Govee Pros look amazing, especially the warm white. Did you end up doing 4 3/4" on this one?

[@jbsdiytv]

Thank you for your comment. We ended up using 4” as it sit center from the wall and fascia board

[@a610412]

When you drill through the wall into the attic to run the wires, what do you use to seal it back up?

[@jbsdiytv]

We use matching caulking or spray it with matching paint

[@hectorgarcia1312]

I have about 200 feet or so that i need covered. Whats the best option to get the best lighting control. Should i get one 150 kit and one 50 ft kit or two 100 ft kits? What option is easier to control and manage?

[@jbsdiytv]

If you get the the Pros 200ft Kit it’s all around easier to manage splicing, length wise and all on one controller. It’s a hot item currently so good luck getting your hands on one of them. Multiple controllers takes away of the the full functionality. One controller works best because both WiFi and Bluetooth work. More controllers, Bluetooth has problems

[@jcaprietta]

How far away from the wall are you guys mounting? Direction says 5-10 cm

[@jbsdiytv]

2-4 inches from the a wall

[@SithLordBishop]

how many extensions do the 100ft and 200ft kits come with?

[@jbsdiytv]

100ft Non Pros comes with 1-12ft extension. The 150ft non pros comes with 2-12ft extension. The 100ft Pros come with 1-12ft extension and 2-4ft extensions. The 200ft Pros comes with 2-12ft and 4-4ft extensions Here is a link to my video on TikTok www.tiktok.com/t/ZT8ccxcUw/

[@eleuteriopazacinta7173]

Great work JB! What is the longest you can connect the Govee pros on one controller? I need almost 275ft. Would they work for that much?

[@jbsdiytv]

The website indicates 150ft so I recommend to do just that until the module driver is released. Now, I was able to do two installs with 12 strands(200ft) and I’ve contacted the homeowners said they have had no issues. I will definitely circle back once those drivers get release. Make right choices, install what’s recommended first. Thank you for your support to the channel

[@eleuteriopazacinta7173]

@@jbsdiytv thank you! Thanks for the info and the great content.

[@Omar-yf4ib]

For this setup were you able to sync both 100ft controllers with each other? I’m trying to figure out if I should buy two 100ft or just one of the 200ft for a two story home. Interested in what you would recommend.

[@jbsdiytv]

Hi there and thanks for watching. What we tell our clients is that if there are big separations in rooflines and they possibly want to light up their sides, that will require huge jumps and different directions of the lights streaming. So it’s best to use two 100ft. Most do ask for them to stream in the same direction so it’s difficult to do that when you have your lights running one direction and need to light the top, then it will run the opposite direction if all on one controller

[@jbsdiytv]

You can then group the controllers in same-model group under the home tab

[@Omar-yf4ib]

@@jbsdiytv cool, thanks for the help!

[@srt8_lockdown782]

Im in new braunfels and lookkng for someone to do a install how much would i be looking for the install

[@jbsdiytv]

We currently have a full blown Christmas light installation season that we need to take care of first and then we will resume after the season is over. Thank you for considering us for youir install

[@johnreese2856]

Looking to do an install in floresville tx with the 200ft pro kit can you give me a price.

[@jbsdiytv]

Please message us on our FB page with the link provided at the top. Thanks 🙏

[@dancevids23]

How do you combine 2 100ft without the module driver?

[@jbsdiytv]

Connect them all together and add 12 segments in the app

[@theRealSara]

Would love to hire you to do a job in Houston - but let me know if that’s too far

[@alvaromarquez1751]

Same here.

[@jbsdiytv]

Thank you for your support. We greatly appreciate it. We will eventually travel throughout Texas. We are Christmas lighting business and we are currently in our peek season of installs. We have a list of clients we have to attend to before we do Gove installs

[@theRealSara]

@@jbsdiytv do you have a website or Instagram where we can message and talk about scheduling an off-season install?

[@Banana69999]

Did you find an installer for Houston area?

[@jbsdiytv]

We have committed to installing throughout Texas now. Please reach us on our social platforms you are needing an install facebook.com/jbsholidaylightingsanantonio?mibextid=LQQJ4d facebook.com/share/uyhZCKLdSA8FwQNK/?mibextid=LQQJ4d

[@andrewalvarado319]

Hi I was wondering if you happen to know if I can splice into a section and branch off with a full section? So basically I’d cut into a section and splice 3 cut ends together essentially creating a Y design

[@jbsdiytv]

You can but it works only in the presets and not in the advanced settings for shutting off lights or DIYs

[@andrewalvarado319]

What do you mean? I’m a little confused.

[@andrewalvarado319]

Basically I can only use the preset settings?

[@andrewalvarado319]

Will the timer still work and the scene I select to come on still function?

[@jbsdiytv]

@andrewalvarado319 most want to do spot lighting with the govee lights and you can only do this in the advance settings and segmented. When you do a Y-split, that data does not read the y separately but as one. They should all act independently from each other. If your ok with this happening then it can be done but there are no special connections provided by govee

[@jk-hk3go]

Hello Sir. What is the best way contact you? I been trying to reach you but was not able to get touch with you.

[@jbsdiytv]

We are a Christmas Lighting business and booked solid till the end of the year. We have a list of people waiting for Govee installs. You can message us at the social media links up at the top of the page