Govee Outdoor Permanent Lights-1st Gen.*HOW TO FULLY CUSTOMIZE*

Welcome back everyone!!! This video is an update to my last Govee Install video. We were back at it in the blistering heat to bring you this need to know content so we can all be ready for Christmas(NewYears, Valentines Day, St. Patricks Day)ect. all the holidays lol. This video might not clear up all your questions, but we are right there to narrowing it down so we can put every penny into this and make it worth it. Please don't hesitate to leave a comment below if you have any further questions . Hit that Like button, share, subscribe to the channel so you don't miss any of the new content. Feel free to ask any questions. Till next time my friends. Thank you for your support.
"Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates"
Govee 150 ft Outdoor Permanent Lighting
amzn.to/3swC3Yr
Govee 100 ft Outdoor Permanent Lighting
amzn.to/49yGMcH
Govee 50ft Outdoor Permanent Lighting
amzn.to/3uiVAMk
PRO EDITONS
Govee Pro's 100ft
amzn.to/3MC6hQy
Govee Pro's 200ft
amzn.to/3svjuDZ
Wirefy 150 PCS Solder Seal Wire Connectors
amzn.to/47idT2I
LED Clips
www.amazon.com/dp/B0B2WY1D2F/...
BTF-3 PIn 18 Awg LED Addressable Wire
www.amazon.com/dp/B07SKGTCWQ/...
Ryobi Brad Nail Gun Brushless 18Gauge
www.amazon.com/Ryobi-One-18GA...
1" Brad Nails
www.amazon.com/meite-Length-G...
Heat Gun
www.amazon.com/Wagner-Variabl...
2"x2" Wood Squares
www.amazon.com/gp/product/B07...
Pickle Potion Sport Drinks
www.amazon.com/Bobs-Pickle-Po...
Ryobi Misting Fan
www.amazon.com/RYOBI-18-Volt-...
Cooling Rag
www.amazon.com/Ergodyne-Chill...
Ryobi Glue Gun
www.amazon.com/dp/B0BP9YM9LT/...

[@nirmal6632]

Best video out of them all. Love how it turned out

[@jbsdiytv]

Really appreciate the comment. Thanks for watching and your support

[@treyibert6715]

Man, excellent video. Thank you for not trying to be a ridiculously acting "Influencer". Extremely informative!

[@jbsdiytv]

Thank you for watching. We really appreciate your support

[@somerandomguy6322]

Dang thank you so much. You answered all my questions and showed me everything i needed to know. Great Video!

[@jbsdiytv]

Hi, thanks for watching. Glad we could help. Good luck on your installation

[@AB_thingsDFW]

The best video for these lights. I just purchased the pro black ones and will follow your steps.

[@jbsdiytv]

Awesome, we appreciate your support to the channel. Hope your install goes well. Reach out if you need assistance

[@chrismeemken6135]

Great job on the video, it was very helpful along with the waterproof splices.

[@jbsdiytv]

Thank you for your support to the channel. Glad we could help 👍

[@christdied4us]

Very neat job I love the perfection you did

[@jbsdiytv]

Thank you!!

[@rhondaholeinoneon16]

Very detailed and helpful video thank you

[@jbsdiytv]

Thank you for watching our content and for your support

[@slongsta]

Just had the pleasure of messaging JB. I want to thank him for taking the time to explain all the possible steps that it’s going to take me to get my lights installed properly. Thanks for putting out these video, kind heart and insight. Let’s follow and subscribe.

[@jbsdiytv]

@slongsta Really appreciate that🙏 Thank you for your support and I’m glad I was able to help you. If I can help, at my convenience I will. Hard work money at stake so do it right the first time. 👍

[@jimdenton3925]

Can't wait to install mine.

[@jbsdiytv]

Good luck on your install. Stay positive

[@terryahrens4942]

Thanks very much for these tips! I ordered the extension cable and connectors, plus the clips, to extend my 100 ft kit.

[@jbsdiytv]

That’s amazing. I hope it isn’t to hot where you live. Stay hydrated and be safe when you install. Plan ahead, measure twice cut once!! Check out my upcoming video for some further tips and tricks. Thanks for your support🤝🙏

[@ssandok]

Where did you get the extensions? I don't see them on their site. That's exactly what I need!

[@murphybalsomi8526]

WHERE DID YOU GET THE EXTENSIONS CORD?(Extension Power Cable for govee H705A)

[@jbsdiytv]

@murphybalsomi8526 Hi there. The extensions come with the 1st edition 100ft and 150ft kits. Also comes in the 100ft and 200ft pros

[@SithLordBishop]

so many good tips thanks!

[@jbsdiytv]

Yes not a problem at all. Good luck with your install. If you really want us to travel to Colorado we can discuss numbers. Just let us know. We have other social platforms at the top of our page to reach us

[@roccobee6773]

Great video. What would they look like if installed closer to wall then 2"? I have some side areas where there is no overhang.

[@robertt8273]

Great video and great advice. I have just 2 comments or suggestions. First, I have discovered that when i use the solider and seal connectors sometimes the wire will poke through the plastic side causing a possible short situation. So i place a section of shrink tubing with the glue/sealer inside over the connectors as added insurance. Then also to further seal with another shrink tube over all three extrnded about 1/2 inch past each end. Second, i had enough overhang of my facia board that i put my lights on the back of the facia board aming toward the house. Thus hides the lights almost completely and lights up washing the house wall much brighter.

[@jbsdiytv]

Thank you for commenting. I’ve never had that issue with this brand of solder and seal when you mention the wire poking through. I have had this issue when using just the heat shrink sleeve without the solder so I stop using that type. The sleeve on these have a silicone in them when they get heated up when properly done. I can see someone who doesn’t know how to work with these have that issue so that is a good suggestion to have another seal cover the hole connections after complete. Wouldn’t hurt. To answer your suggestion on the lights on the back of the fascia facing the wall. Installed this way for one of my clients because they asked for it to begin and they ended up not liking it. They would rather have the triangle effect like shown in my videos instead of blasting light shown on the wall. Of course they paid me to re do it and it wasn’t worth the hours and headaches we got from it so I’ll never bring that up. I do mention to all my clients that it isn’t track lighting. Most of them are ok with it because it’s a knockoff from bigger types of lighting at a lower cost. For the ones that will pay to paint the lights to match the soffit, I’ll do it for them. Also have to consider a house I did had 4 different soffits spacing in the front alone, some 5inches some 12 inches and the others in between. Casting would've been different in those areas. So to keep everything even as I always recommend 2 to 4 inches. Thank you, this will help with someone’s install

[@jasonh.3156]

Do you have a video showing your install with the lights installed onto the fascia board having the lights pointing back at the house? What was the estimated distance between the light to the house?

[@joseluisperezjr3285]

Literally the comment I was looking for !!!! I wasn't sure if the lights would light up decent if I did that, because I noticed that if I installed them as you did it would preety much conceal them...

[@jbsdiytv]

2” from the wall

[@lalomtz84]

​@@joseluisperezjr3285Yea, i'm also interested in seeing how your installed lights look .

[@aztecghost9058]

Great video.. Thats what I would expect a professional install to look like. I didnt even know about those water proof heat shrink. I could have definitely used those both times I've put lights up. I wish Govee gave us some color options for the cables though so you didnt have to color match. Maybe one day

[@jbsdiytv]

I really appreciate you taking the time to view my video. I really like how you spilled out in your video what needs to make sense when installing these Govee lights. Everyone pays a pretty penny to buy these govee lights and everyone ask these questions but that’s the reason why they do it, so you can buy more. I’m trying to help to viewer so that’s why I started making videos on theses lights. I don’t know what happened to my comment on your page but I’d like to post again if your ok with it. Maybe one day we can collaborate on a topic. Good luck with your journey my man.👍

[@blackmacgyver9965]

Thats a tight i stall dude , looks great 👍🏾👍🏾

[@jbsdiytv]

Thank you!! Thanks for watching

[@hotrodsbikes8460]

A collared shirt on a Christmas light install is hilarious 😂

[@HughsReviews]

I got two of the 150’ kits and did the whole house and entire perimeter fence in the backyard. These lights are fantastic

[@jbsdiytv]

Yes sir they are. I understand that the line can be seen and everyone mentions that but other than that, why spend 2,000 extra on something else when you can improvise with these. Awesome, glad it all worked out. 💪 👊 Hey look it this way, you can do a review on it. Every one of my videos is Creative Commons so you have my permission to use my video as an example👌

[@martybli]

How do you do the perimeter fence? Do you have them pointing down?

[@jbsdiytv]

@@martybli thank you for watching my video. If you decide to do this on the picket side(usually to the street) then the white wire will stand out and the lights will need to be put on their sides if you want the triangle effect. Or you can face them out. If you do it on the inside, it would work on the edge of the top rail 2x4 with the adhesive pad and clips. This install will be close to a home installation look.

[@benbarlow6135]

@@jbsdiytv I know you can't do any more than 150 ft of lights but if the house is bigger than that, do you just need to connect it to a different outlet? And can you sync up the different 150 light strands if you had two different segments?

[@jbsdiytv]

@benbarlow6135 please message us on Facebook @Jbs Holiday and Christmas Lighting LLC or Instagram @ jbsholidayandchristmaslighting

[@DS-home]

Do you know of any manual or clear instructions for programming multiple sets of lights? Also, is there any info for controlling groups of lights when outside of bluetooth range.

[@navygreeny2]

What was the lighting pattern at the end of the video or did you program it yourselves? And cool video

[@tommckenna602]

Great video! What gauge Brad and what settings do you use on your Ryobi air strike? Thank You Tom

[@jbsdiytv]

Hi Tom, thanks for watching our content. We are using 18 guage - 1” brad nails since our Ryobi Brad Nail gun requires 18gauge only. Follow what is recommended on your tool. Thanks for your comment

[@n0rms23]

I knew that looked like Texas ! Lol I hope that’s San Antonio! I would definitely hire you all for install 😂

[@jbsdiytv]

Your in luck😂 we are located in San Antonio

[@jacquesm1553]

I bought the 150 ft. I have those areas above the garage as seen in the video. I will have to cut. I wanted to know if I can cut the 150 feet. I am not sure if it says it cannot support more than 150 feet of light or more than 150 feet of wire. Please help

[@612doteth]

@4:04 Nice Catch!

[@jbsdiytv]

Thank you for watching. Thanks, it was the sound of the swoosh that helped me find where it would land 😆😂

[@richardanderson7546]

love the video but no how do I hire you do install my govee lights?

[@Kevinw4040]

Hi there thanks for the video. How does that 18/3 connector wire hold up to the elements over time being exposed to the TX heat, rain, etc. just laying on the shingles like that? That's my only concern that it's not hidden behind the eaves in the attic. I live in FL we have horrible humidity and sun.

[@jbsdiytv]

The lights and wire are rated IP-67 rated. 65-67 both provide a high level rating and provide excellent protection for outdoor enclosures. I did spray a clear protectant over the line of the 12’ extension to protect it from some of the elements which I didn’t show in the video. I apply this to most painted materials when I do handyman projects to protect outdoor paints exposed to elements. Some of these items we keep addressing in our future installations so it wouldn’t hurt to protect them more if you can. Thank you for your questions

[@hugomolina3522]

Hey sir. How you doing? I bought 2 set of 50ft. I was planning to connect all 6 string to one power supply can that be done? When I need to do 3 jumps One of 17ft, 11ft and 9ft The first jump I have to cut between lights in the 2nd string I use 18g wire and make sure all the connections are good I power up and only 1 light turn on after the jump. The wire jump is 17ft What do you do when you do jumps like that?

[@rogerbegaymd2101]

Thank you for sharing. Where did you purchase your plastic clips that you used to secure the wire?

[@jbsdiytv]

Yes sir not a problem. Thanks for watching and your support kzbin.infoiwZyyI3RXUw?si=No63RzoIg5R__-ET

[@chadchittenden9943]

I live in San Antonio and about to purchase a 100ft. set of these lights I have a single story house with 3 peaks could you give me a rough Idea how much your install would cost?

[@luisescobar8983]

Hello I have question?? How much do you charge for installation of the lights

[@pgonzales9795]

Do you do installs? If so, where in Texas are you located? Looks amazing, awesome job.

[@jbsdiytv]

We are located in SA, Tx

[@tinakaiserveloz]

Hi! I’m in Cibolo, Tx in a very similar one story home as in this video. I would also appreciate if you could give me a quote for install. Thanks!

[@jeffmullins1665]

I thought I saw somewhere that when you cut the light sections there is a minimum number of lights needed in that section for them to still work. I have a corner overhang that would only need like 4 lights on it and it would be spliced on both ends of that four light strand. Would that work out cause a problem? Thanks and great video.

[@jbsdiytv]

Hi there and thanks for watching. Yes, they are group of 4 sections. You can’t end with less than 4. When you splice it, make sure to use liquid electrical tape. Before you do that, make sure no copper strands touch each other. I have a new video coming out that explains the set up and app features that will explain your question.

[@ExperimentalLawn]

What wire do you recommend when your splitting strands to make eve jumps? Do you have a link to that as well?

[@jbsdiytv]

Oh I’m sorry about that. Must of missed it. I will place it in the description now. Thank you. The link is available

[@cabotheduckdog1039]

Did you just use one controller for all of these lights?

[@michaelrourke2182]

Where can I find information on installation? I'm located in San Antonio

[@milamber1b]

What product would y'all use if you needed to do a 3 way split, not just 2 way? I have a house I'm going to be doing and they have a gable as well as a straight area to cover.

[@jbsdiytv]

We typically don’t do 2-ways or 3 ways because the devices can be grouped as one system. If you wanted to make a 2 or even a 3 way, just keep in mind whatever line you tie into, those lights will mirror that strand. Which is not a problem when you use your Govee scenes but only a problem when you do your accent spot lighting as you turn a particular lights, the strand attached will also respond. He is something you can try out to see if it works for you amzn.to/4aFXiYn

[@jamestipay2486]

Hi, what wires are those on 12:15 time stamp to jump over the 2nd floor roof? We’re thinking of doing 150ft around the house and a 100ft at the 2nd floor, do you have the link for the 12ft extensions or was it provided by govee?

[@jbsdiytv]

Hi there. Thank you for watching my video. That is the 12’ extension provided by Govee. There were two jumps like this. 3 and 7. They were 9ft jumps only and I cut the connections off so that way we did not have all that extra line left on each one. Then those cut off connections, we used them in other locations we spliced the strands and put the heat shrink sleeves with the solder. I hope this answers your question. If you need to make small jumps, the link is in my description (18-3 BTF) Keep this in mind, 100ft box comes with one 12ft extension. 150ft box comes with two 12ft extension. Look at your house and see if you will need two major jumps. Unfortunately you can’t just order extensions last time I checked.

[@jeves360]

There is a new model coming out it's the Permanent Outdoor Lights Pro model H706C. I am currently testing them out. Biggest difference is they come in a 60m or 196', this is what they sent me. Also they are able to be spliced. They sent some connectors to allow the splicing. So far so good. Great video btw. I used this for my install.

[@jbsdiytv]

Yes that is correct. I follow the Govee group’s and comment on their ads. Seems like they might have a different color of line instead of just white. We will see. Thank you for watching, glad your installation went well

[@jeves360]

@@jbsdiytv I got white, so not entirely sure about the color but I've read that somewhere also. I posted a small review on the community page at Govee.

[@mpratt69]

@jeves360 where did you find this info? Tried googling the model number a bunch of different ways to see more info on them, but couldn't find a thing other than an item number in an obscure page in their site like a placeholder. Super interested in checking these out before buying and having to splice. Any details would be really appreciated

[@KY_CPA]

​@@mpratt69They're selling them on the govee website now

[@mpratt69]

@@KY_CPA right, but this was 2 months ago. Salty they just liked the comment and didn't tell where tf to find em.

[@gigi9697]

JB, where can I find the water sealed connections for the jumps? Would you have a link to the item?

[@jbsdiytv]

Hi there. Links is in my description. Thanks for watching

[@cruzyosabeth]

Hey I have a question in the product description it says not to cut it but you did cut, that is possible then and what extension cable to use

[@jbsdiytv]

The link to the 18-3 wire is in the description. You can also use 20-3 if it isn’t available but keep them under 2ft to avoid voltage drop. You can splice between the 12ft extension provided by Govee but keep that under 18ft

[@kj5905]

Do you think it’s ok to use Brad nailer on vinyl plastic soffits? I like those clips you have links for so I hope I can brad it too

[@jbsdiytv]

Use fine point small screws so it grabs the vinyl soffit

[@bpage6636]

You guys did an amazing job. Do you install these for anyone and if so how can I contact you for a job?

[@jbsdiytv]

Thanks for watching. Yes we do, going on our 67 install this year in Texas. We will be going outside of Texas middle of next year. There a social media links at the top for the page

[@michaelpenn5224]

Hey JD, sir, you did a heck of a job. I just had one question for you, I have to use two 100 lights per side of my home with two different controllers. Is there a way that they can be synced together. Thanks for the video. Very nice.

[@jbsdiytv]

Hi there, yes there is a way called grouping the controllers. You can also set timers and schedules. In there, if one 100 is going one way and the other is going the opposite way, you can adjust one to clockwise and counterclockwise. Go take a look at the Govee app (Detailed video) for a visual. Good luck

[@michaelpenn5224]

@@jbsdiytv you the man. I appreciate it. Have a good evening.

[@jbsdiytv]

Not a problem. Good luck

[@michaelhaase778]

Can these be face mounted..on part of my home I don't have a soffit..but wat lights there...what do you think

[@jbsdiytv]

@michaelhaase778 you can face mount them but it will be super bright to passer byers and cars. You won’t get any lighting effects on the wall

[@sheananos770]

I’m installing 2 150ft stands on my house.. since they can not be connected, can they be programmed on the app together so if using some light settings they are in rhythm?

[@jbsdiytv]

Hello and thank for your question. Yes they can be programmed together. Go to home in the app, then hit the plus symbol, then with select type on the screen then select same-model group control. You will see two model controllers in there so select both. If you haven’t figured it out, I will have a video coming out soon that goes in depth with the app. Thank you

[@a610412]

When it comes to Vinyl soffits, do you still use brad nails to secure the LED clips?

[@jbsdiytv]

Haven’t done vinyl soffits yet

[@jimbates6227]

Can these Govee light strips be spliced anywhere along the 16ft string? I just finished a 100(ish)ft section (with 6-16ft sections) and need 1 more bulb to perfectly complete the 100ft section. I have a 7th 16ft section to use as the donor of the extra bulb.

[@jbsdiytv]

Yes they can be sliced but not less than 4 lights. You can only have 3 segments(stands) in a 50ft kit, 6 segments on a 100ft but can add 3 segments and 9 segments on a 150ft box. You can’t add to the 150ft.

[@knpg119]

Where. Can i get those clips for hold the wire any links or any recommendations thanks

[@jbsdiytv]

Take a look at my Govee/ AliExpress video

[@bac4998]

I love the concept but hate the spotlight effects from source of the light. I wonder if the neon rope lights will perform better.

[@jbsdiytv]

The 1st generation Govee lights are not great for spot lighting. But the Govee Pros for that

[@RichardHarrison2014]

Very nice job! One question, I just purchased a Govee RGBIC Permanent Outdoor light Set 100' Model H705A can these be cut to fit? I have solder waterproof sleeves but not sure what happens if I cut this run ....These things cost way to much to screw up!

[@jbsdiytv]

Thank you for watching. The kit on the Govee website does say do not splice. Now, they say that cause if you do, it voids their warranty. That doesn’t mean they can’t be spliced but you need to have some knowledge of voltage drop when customizing your own length of wire jumps and take the amount of strands you have vs how many times you have to customize. Like I mentioned in the video, do all this at your own risk

[@user-wx9dg4xe7t]

What's the best distance you recommend from wall for best results? Thanks

[@jbsdiytv]

Hi there. We install all our lights 2-4” from wall. You will get a nice triangle effect and it looks clean. Most want to get away from those measurements and get a round look but that looks somewhat ok for the scene modes but does not look good when accent lighting is used. Hope this info helps

[@efthimios]

JB, would you be able to share based on your expertise, are Govee PRo same, better or less quality compared to trimlight , oleo or minleon? Guess my point is will these be with installing and lasting long enough compared to competitors ?

[@jbsdiytv]

I never encourage defamation of another business practices. Govee lights don’t have a track vs the other competitors installs. Factor that in price. I have had my no pro lights on my home installed for about 2yrs now and can say this, I run mine for 12hrs everyday. They look great and are bright. The light is defined by the cone on the wall. It’s not a must to run them that long but I’m doing it for testing purposes for longevity. They do have 50,000hrs of life. You can have your lights stay up there on the soffits if you actually take some extra time to clip every light, use 3D mounts sold by others or customize yours to raceway channel. Other businesses who install permanent lighting are now competing with homeowners purchasing their own type of permanent lighting so of course bash the product off info on research that a bad installer did. Do it right the first time and you won’t have problems. From an installers perspective on the non pros and pros, we choose to install the pros because they are easier to install. For example, the non pros are one directional LEDs when splicing. It must all go back the way it was cut. The pros, the strands don’t need to be cut in sequence. I can take a piece from another strand and they still work. You still need to keep the connectors running the same though. Non pros are not warranted after splicing but pros are warranted if spliced. The non pros use 3 colors to make white vs the pros have specific LEDs designated for both warm and cool white and that’s a major pure difference. On non pros when installed from left to right it shows white with a tint of green and when installed right to left it shows white with a tint of purple. Pros are slightly brighter. Hope this gives you a perspective on the product and the two kit differences

[@user-le8yj8ki3c]

I got the 100ft goove permanent light pro lights. I think I am only putting the lights in front of the house and will have about 20ft left. can I just cut at the end and does the 100ft comes if different roles or is just one long string?

[@jbsdiytv]

Hi and thanks for watching. You can cut them. The strands come 16ft 7inch in length and have 10 lights in each strand. It comes with 6 strands

[@IMiss_The90s]

Can you turn off individual lights? I just purchased (2) 100 foot sets but there's a few spots I need a few turned off to make them look good.

[@jbsdiytv]

Hello and thanks for visiting the channel. Yes you can. Open the app, instead of segmented go to advance settings and in that area, you’ll see a snake line. In the color buttons there will be one that has a red slash on them. Use that one to individually turn off specific ones you have customized. This cannot be done for the preset scene modes. Hope this helps

[@CentalBama]

Have you ever installed on a fully perforated/vented vinyl soffit? Hoping install in the next few weeks, and while Alabama weather isnt as extreme as Texas it's still hot enough I worry about relaying on the 3M tape. It's been suggested to use furring strip.

[@jbsdiytv]

Hi there, thanks for watching.Unfortunately I have not but all that I have read on some installs we’re using small white zip ties. Sorry I couldn’t be much help

[@mpsmoov128]

You probably already figured this out but could use liquid nails and or more clips on the soffit. Ive seen people install on the strip that is way farther than the 6in they recommend. It changes the way the light looks; less cone more mixed. What did you end up doing?

[@jbsdiytv]

@mpsmoov128 yes we have started using way more clips than what Govee recommends. We purchased a bulk amount on Ali express since we are doing 1 govee install a day. Also, I don’t recommend using liquid nail on these lights. We have tested them out and during the installation the strand stop working so our installations are easily able to slide the strand out of the clips and replace a new strand. Also, if one goes out in a few years, they will damage when removed as wood and hardiplanks paint get removed from the surface. We install all our lights 2” from the wall using a 2x2” cube. We bring this up to every new client and they agree because they have seen my KZbin channel. 6” is something we tried and our client ask us to move it closer cause they didn’t like the round effect. They paid us extra to do it

[@CentalBama]

We are using up J channel, at 2 1/2" from the house. Christopher helped to explain a few questions we had about jumps. Had planned on renting a boom, but HD is having issues, we are hoping that a replacement battery shows up tomorrow so don't have to use a ladder

[@jbsdiytv]

@@CentalBama awesome glad he was able to help you all out. We have to keep it affordable for our clients. Seems like they want a really nice install for a low price. Might do this with my own house. Thanks for the info

[@scarletfire9812]

I cut my Govee permanent outdoor lights in 6 different places. So basically I have six extensions of 18g 3 wire. And they work perfect

[@jbsdiytv]

That’s awesome. How long were your jumps?

[@scarletfire9812]

@@jbsdiytv Four 10' jumps, two 6' jumps.

[@jbsdiytv]

Nice..1st Generation lights or Pro’s. The pros just have magic wires for some reason lol

[@scarletfire9812]

@jbsdiytv 1st gen, But i'm having problems with the timer. They come on at set time but don't go off at my set time. I when I turn them off manually they magically turn back on thirty minutes later. And the set scene playlist doesn't start when timer turns lights on 🤷‍♂️

[@jbsdiytv]

@@scarletfire9812 only set a timer at the front page to go on and off. Then in automation just set an On and the days you want the scene to start. Don’t set an off in automation, just a On

[@charliehoogewerf2824]

My question is if you're stranded exceeds one control box and you need to use multiple control boxes is there a way to sync your lights up together so they do the same light pattern

[@jbsdiytv]

Yes, in same-group by adding both devices

[@mrbaseball12mom_bot]

Have you done an install where the lights were facing out?

[@jbsdiytv]

No we have not. Govee lights are intended to be installed on the soffit. Facing out will take away from how they are intended to look or installed

[@gregramirez1946]

Hi, do you do installs? I live in SA and I’m ordering the 150 ft pro set.

[@jbsdiytv]

Please message us on Facebook at JBs Holiday and Christmas Lighting LLC or IG @jbsholidayandchristmaslighting

[@theword2011]

I think we need to talk about the dude on the ladder that just vaporized into another dimension.

[@jonnysmith6701]

I have my last section after a splice not working with the colors or app just white lights any ideas

[@jbsdiytv]

That’s a bad strand. You can try a factory reset holding down the power button on the controller for 6 seconds and then after a short white flash. If it continues then it is indeed a bad strand

[@SWCHEEZ]

I'm getting syncing issues between jumps, before the first splice works, after the spice only does white. And recommendations before i order another set?

[@jbsdiytv]

That’s is a bad strand. We have encountered this in many installs. Don’t order anything. Take a photo or video and post it to the Govee website for a free strand replacement. Well you did a custom jump probably so you will probably not get another free strand

[@cm.5023]

I may have missed it but are you using one controller for the two 100ft kits or did you link the two somehow? If linked how and how many can be linked?

[@jbsdiytv]

Hi there thanks for watching. I used two controllers and power adapters. They can be grouped in same model

[@DRobertson725]

Are the clips you used the ones listed as LED clips in your description?

[@jbsdiytv]

You can use those in the description or give see my Govee/AliExpress video for the naming of the clips

[@PatriotDad]

Is there a maximum distance you can splice in an extension between two lit areas?

[@jbsdiytv]

Yes. If you use the 12ft govee extension, you can splice 5-6 more feet inline of it

[@wolivere]

If say, I buy the 50-foot kits. I have 3 areas of the house to cover. But each section is really only 40 ft. Can you cut off the last 10 feet?

[@jbsdiytv]

Hi and thanks for watching our content. You just need to end your lights with 4 or more for them to work. If your jumping from eave to eave then you can cut anywhere. Keep your jumps small, less that 2ft and a minimum of 4 total

[@donaldlewis499]

Damn, i got mine further away from the house. I hope i can move them back some. Just put a strand up.

[@jbsdiytv]

😁just one strand, you can still move it

[@JimAbbett]

I want to install these on my house but worried about the wiring sticking out like a sore thumb during the day. My siding and soffits are vinyl. I'm not spray canning on vinyl. They should consider selling grey, tan, etc colored wires. Your video and process was great except for the spray paint overspray. What happens when it comes time to paint the house?

[@jbsdiytv]

Hi and thanks for watching. These are items we discuss with our clients before we start any quotes. We have to make it clear before we proceed. This is a 3rd party product and warranties it comes with it is what you get. Of course, if we are in the area we will definitely replace a strand if it goes bad once the client requests warranty replacements or buys new strands. Our clients are fully aware and majority just want their lights up

[@bhburks]

Did you use 18/3 stranded wire? I need to make a few smaller jumps and want to make sure I’m getting the right stuff.

[@jbsdiytv]

Yes sir that is correct. I have that product in the description of one of my videos. I’ll check and see if I have it on the others as well. If it’s not there I’ll add it. Thanks for your support

[@bhburks]

I should’ve looked in the description first. lol. Thanks!

[@jbsdiytv]

No worries all good. Good luck with your install. Be safe

[@random_24663]

What is the distance between each led light? Is there a maximum distance you can go with the extension, I'll be using he 20awg wires for that purpose.

[@jbsdiytv]

Hi there. Light spacing is 17” center to center. Govee provides a 12ft extension in the 100ft box and 2-12ft extensions on the 150ft set. If you’re going to be using custom wiring, I would only use those for small jumps like 1-2ft. If not you have voltage drop and cause flickering in your lights

[@heymapll33]

I was wdonering, how did you get the bottom of the house to connect to top? It doesnt look like yoiu used same string for everything. Or did you?

[@jbsdiytv]

Hi there. Thanks for watching. At the beginning of the video there is the planning for a guide. The longer jumps we used the 12’ blank extensions provided by Govee, the rest of the jumps were 3-18awg wire. Hope this helps

[@ryanlowrie3689]

When you mention to only use the insulated 3 color wiring over a small distance, how small of a distance does it have to be? Would it work over 5-6 feet?

[@jbsdiytv]

That wire was 20gauge, if you need to jump that then use something thicker between 16-18gauge wire

[@AEpstein]

The pros are sold out everywhere. Are the original ones worth purchasing? I don't have a complex layout.

[@jbsdiytv]

Only difference is that they have designated warm white LEDs vs the 1st gen uses other colors to make white. Also would like to add that the 1st generation lights void the warranty if you splice and the pros doesn’t void the warranty since it can be spliced

[@willburk]

Thanks for the videos! Your mount clip link is for transparent clips. Won't those break when I try to nail them? Do you know where to find the white plastic clips?

[@jbsdiytv]

Thanks for your comment. They will break if you have your brad nailer at max power. There is no need for max power. Set it to the lowest and adjust the nail head wheel on the side of the gun. Hope this helps. Links to all my products are in the description(3 dots)

[@willburk]

@@jbsdiytv Thank you!

[@willburk]

The clips linked are unavailable too. Maybe you can update the link?

[@jbsdiytv]

Ok thanks for the update. Go to aliexpress and buy a bulk amount for almost the same price. It’s called RGBCCT Official Store. 10mm PCB. Good luck

[@willburk]

Amazon still has them; just not at that link.

[@joseg.5937]

What is the distance you use to install them from the wall? Looks really nice.

[@jbsdiytv]

Hi there and thanks for your comment. We used a 2x2 (2inch) wood craft block to space our lights for install. This helps to give the cone effect that everyone comments on. There is a link in my description to purchase either 2,3 or 4inch blocks. Further than 4” makes the light expand out to a rounded look if that’s your thing.

[@joseg.5937]

Thanks for the fast response!

[@edhammel9535]

Jb … thanks for the vid. Just finished my install. Only snag was on the jumps. I used my own 18 gauge 3-wire but my jumps needed to be 11’. The system didn’t work until I shortened the jumps to about 6’. What do I do if I need longer jumps at 11’ or 12’ ? Will use if the two 12’ jumps supplied by Govee do the trick? What if you don’t have male and female Govee ends to add on like in your video? Appreciate the help. Thanks for the reply.

[@jbsdiytv]

Awesome. Glad the videos could help with your install. What kit did you end up buying? Pros or no Pros? Once you provide me with lil more info to the kit you bought I should be able to help out. One thing I can say is that if you need more than 12ft jumps we have spliced 3-4ft in the middle of the 12ft extension. The signal boxes in the Govee extensions need to remain

[@edhammel9535]

I have the H705C kit. 150’ with two 12’ Govee extensions. I needed to cut and splice at two different points to reach a roof peak. I used 18 gauge 3-wire jumps that were initially about 11’ each. This resulted in flickering about half way past the first jump. When trouble shooting, I cut the first jump down to about 6’ and the prob was solved until the next jump. When I cut the second 11’ jump down to about 6’ … entire prob solved and entire system works fine. But I really need those two jumps to be about 11’ each to hide and run the wires correctly.

[@edhammel9535]

Did you mention that those 12’ Govee extensions have “signal boxes” ?

[@jbsdiytv]

@edhammel9535 I see. It’s tough to splice with the 12ft extension on the 150ft kit since they have them on both ends. You could purchase the Asahom 6ft extension from my site to use their connections

[@jbsdiytv]

@edhammel9535 lnk.bio/jbsdiytv shop permanent lighting accessories on my site and look for the Asahom 6ft extension with amplifier

[@hahasteven2266]

So if I purchase 150ft in length I technically if need to jump or other length added through 18/3 they can be extended longer than 150ft. Is that what I understood?

[@jbsdiytv]

They can’t be extended pass 150ft. If you have say 115ft then all your small jumps (2ft or or less) need to stay under 150ft

[@ignaciorivas4712]

Link provided for the clips are little different from the ones used in the video. I would like to use the. Nail gun as well will these clips made of the the Same material. I would hate to purchase them and find out that they crack if nailed with gun. Thanks for the video

[@jbsdiytv]

The ones you are looking for keep selling out. Yes those are different but they work for all our installs. Make sure it sits flat on the surface material

[@dustinwhite8186]

On the 150ft can you use both 12 extension cords in a row to make a 24ft extension cord without any issues?

[@jbsdiytv]

Don’t use them back to back to make 24ft, it will cause flickering. What we have done is use a few lights in between the extensions so they act as data boosters

[@patrickr2553]

What is the size of that little block you are using to place the lights so they are even? 2” x 2”?

[@jbsdiytv]

That’s correct. Thank you for watching our content

[@adamjensen6453]

Can i use a 3rd party splitter on what controller? I want to make a jump from first floor to second floor without cutting. I have seen that another company makes a 2 to 1 splitter will thr lights all function correctly?

[@jbsdiytv]

This I’m not aware of. If it can be done I’d like to know about it to make content on it and I will reply to your comment with a video

[@paulmaestas8709]

You you able to run just white lights with these govee lights you installed? Mainly for the summer or non holiday months. Thanks

[@jbsdiytv]

Yes you can do cool white in advance and warm white in segmented

[@paulmaestas8709]

@@jbsdiytv Are these the regular Govee or PRO?

[@jbsdiytv]

These are the first generation lights

[@dward360]

What is a heat shrink sleeve? Is that the same thing as the govee extension?

[@jbsdiytv]

No it’s when you splice the wire and you need to bring the wire back together , you use the waterproof heat shrink solder sleeve to bring them together for a solid bond. Then you use the heat gun to shrink it. I don’t recommend taping or crimping it

[@Liljoe371]

Do these sync with music out of the box or do you have to ourchase the Govee music box?

[@jbsdiytv]

You can sync with mic or phone

[@deldeek]

Nice , do you guys offer installation of these lights ?

[@jbsdiytv]

Thanks for your support. Yes we do. We are located in San Antonio,Tx.

[@JOEZ7115]

When you say that wire should only be used for smaller jumps. What length would you consider to be smaller?

[@jbsdiytv]

We typically use the 18-3 or 20-3 for at least 2-3ft jumps if we have one or two jumps and 1-2ft if we have three to five jumps. If you have jumps longer than 6ft I don’t recommend using this with out some kind of data booster or splicing some lights in your custom extension because the lights themselves can be used as data boosters

[@gbenjamin28]

What kind of nail gun are you using with nail size?

[@jbsdiytv]

Ryobi Brushless 18gauge nail gun 1” nails

[@migueljrcaceres]

I cut mine right before the quick connect with the 3 pins and when I splice them and put them together after a 7 feet extension the rest of the lights did not light up anymore 😢

[@jbsdiytv]

How long was your jump?

[@pigbait85]

Hey, I told you I would update you on the data boosters I got. Working perfectly with 24ft extension and 5 sets after the extension

[@jbsdiytv]

Where did you get you data boosters from? Do you have a link. Maybe on the next video I can try this and give a shout-out to pigbait85

[@l33tur57]

@@jbsdiytvI’ve previously used F-Amp data boosters, as well as Quindor’s data boosters. He might be referring to one of these.

[@jbsdiytv]

Awesome. We will purchase these and test them out in the shop. I will perform some test and if all succeeds, I will use them on my next video and make sure to shout out to both your KZbin handing. Much appreciated it

[@pigbait85]

@jbsdiytv yes sorry for the reply. I used Quinn's data boosters as the are rated for 48v and govee runs at 36v

[@jbsdiytv]

Thank you for the update. We will try this as well and try them on the next video

[@migueljrcaceres]

@ 8:18 what does that mean make and female side? What’s that for?

[@jbsdiytv]

Hi there and thanks for watching our content. When describing connections the connection that has 3 holes is the female side and the connection that has 3 prongs is the male side. This matters because if you have a power supply on the right and you start left with the connection to the controller. You have to remove everything and flip it

[@CivicSav99]

Forgive me if this is already answered: You mention the white/green/red wire should only be used for “smaller jumps.” “Smaller” is relative. What length would be considered too long. I have a 14’ and 9’ gap I am trying to figure out. I am completely stuck considering Govee only provides ONE 12’ and does not sell additional strands by themselves. Please advise. Thank you very much.

[@jbsdiytv]

Hi there and thanks for watching. No worries at all. If you have just one small jump that is about 3ft then it’s doable but if you have multiple(at least 5) jumps then you will need to try and keep those under 2ft. On the first generation lights, the 100ft kit comes with one 12ft blank extension. The 150ft comes with two. On the Pros, comes with one 12ft blank extension and two 4ft. Hope this helps you

[@SGMercer]

I ordered a 150 foot kit and believe it only came with 1 extension cable

[@jbsdiytv]

@SGMercer it should come with two 12’ Govee extensions. Check one more time, if it doesn’t have it then reach out to Govee website for support and let them know

[@Anthonysni92]

How much do you recommend charging to install these? & can I buy two kits but they work together on the app?

[@MMARIC20]

Hey JB does this Ryobi brad nail gun has nails that can go into metal soffits?

[@jbsdiytv]

The Brad nails will be loose on aluminum/metal soffit. I would definitely get one full 200ft kit to light up your front and keep a 100ft where it’s less visible to the view. Not sure how your house is positioned in a cul de sac or at corner but use your best judgement with that. Just know that you can group your devices Here is an example of how to go about the panels that have holes if yours are like this instagram.com/ourdiyhomeproject/reel/Cz33AkvL0Lk/

[@MMARIC20]

@jbsdiytv sounds like I will be on the scaffolding screwing in the small clips instead of nailing them 😆....keeping the layout of my house in mind I have 3 weird jumps at the front , I may do 2x 150, one 150 will cover the front ,with the akward jumps, most of the house and than towars the back dobthe 100ft. I would just like to use the same power outlet. Not sure how that would work on the application. Since it would be going to two different directions from the same power outlet.

[@MMARIC20]

@@jbsdiytv I just saw the video I may do that...thanks alot.

[@jbsdiytv]

@MMARIC20 yes that’s correct. Govee presets will be different directions but your DIYs you can change the direction from clockwise to counterclockwise

[@josecapetillo6034]

What was the total linear length of lights installed on this video? And if you have a constraint of 150’ per controller, how do you get all lights to be in sync?

[@btr8jb]

I think he said it was 100 feet in the beginning. Govee sells a light show box that can control multiple lights using Bluetooth and can also synchronize them to music

[@jbsdiytv]

Hi guys, thanks for watching. Been super busy with Christmas and Govee installs so I apologize for the delay. We used two 100ft kits as one side was 95ft and then the other side was another 95ft. We were able to group the controllers in same model group. Yes the the light show box your talking about is this one, see link below amzn.to/3Td0cOA

[@dbelldaddy2023]

What if my gutter is only 80 ft what do I do with the remaining 20 ft can I cut it?

[@jbsdiytv]

The strands are 17ft long each. 5 of them gets you 85ft. Cut off the remaining 5ft

[@jerometabbert8641]

How long did you make the jig to keep the lights off the wall?

[@jbsdiytv]

It’s a 2”x2” crafting square. The link is in the description

[@veroniquebise8897]

Would you come do an install in Colorado? Thx

[@jbsdiytv]

Hi there and thanks for watching our channels content. Yes we would consider it. Please message us on IG @jbsholidandchristmaslighting or on FB @ JB’s Holiday and Christmas Lighting LLC

[@veroniquebise8897]

@@jbsdiytv thx I messaged you on IG :).

[@Scott-iw8yr]

Whats happens if you exceed the 150ft light? I bought two 100 ft packs just curious. I will probably wire the back side of my house with the extra 50ft if it just cant be done

[@jbsdiytv]

There are two types outdoor permanent lights. Once being the non pros and the pros. Please specify which 100ft kit you purchased as each example doesn’t apply to the other

[@Scott-iw8yr]

@@jbsdiytv Yeah mine are non pro. I know the pro version supports 200ft.

[@jbsdiytv]

@Scott-iw8yr ok thank you for that info. On the 150ft non pro kit which is model H705C supports 9 strands(9 segments) 108 lights. Anything pass this one device model will not light up nor read in the app. Yes buy a 50ft and add them in same model group to control as one

[@garylarrew6321]

Wanting to get my done but to high for me. Do you install?

[@jbsdiytv]

Yes we do

[@user-oq2ow2ho2r]

I have a set of 100' and have had the same issue even with a replacement kit. Both sets lights stop working and resets reconnect to power nothing works. The controller responds in the app its just the lights never come on. With your experience have you ever had this issue? If you have how can it be resolved? How can you fix th

[@jbsdiytv]

Hi there. Thanks for watching our content. Have you made sure your segments are correct under settings? I would first do a factory reset by holding down the power button for 5-6 seconds, check if that works. If not, go to your settings and make sure the segments are correct in there. If none of this works, start troubleshooting. Grab your power adapter and controller and test each strand to respond to the factory reset

[@thebionichandman8967]

so that entire strip was powered from one location? im asking bc i was going to power from 2 spots bc i didnt know i could cut and extend where i didnt need lights in order to get to the second floor. also does it need to stay on constant power or can it be on a switch and still function properly?

[@jbsdiytv]

Thanks for your comment. At the beginning of the video, it showed two outlets on the back left and right. We only captured 100ft kit to show how to connect, set up that all your strands and make sure they work before install. It was 95 ft to the left and 95ft to the right so this install had 2-100ft kits which were grouped later in the app. I have installed the lights to an outlet that was in a switch so no not necessarily consistent power if that’s all you have. Just know if you’re somewhere and want to control your lights you won’t be able to cause that outlets in a switch.

[@thebionichandman8967]

@@jbsdiytv okay that answers my question then. I didn't know you could pair them together so that they would sync up. I'm that case I can wire from 2 spots constant and have them on a timer within the app.. Than you sir

[@jbsdiytv]

@thebionichandman8967 yup you can group them. Go to home, then to group, plus symbol, then same-model group