Thank you Kane, I followed your exact instructions and it worked out beautifully.
@thekanemadness16 ай бұрын
Awesome - glad it worked for ya!
@jeremyfinn9031 Жыл бұрын
I bought the ghdp with that monster ram elbow and been wondering how to go about adding that heater element and if the wiring would be long enough. First video i have found that was detailed and to the point. Thanks for the great video!
@thekanemadness1 Жыл бұрын
Awesome. Glad it helped!
@mrnkognito4 ай бұрын
I like the picture of the Duke on the wall in the background.
@thekanemadness14 ай бұрын
Gotta give respect the Duke!
@EKevanEK Жыл бұрын
Noticed the Alberta plate 🤟 I'm in Fort Mac I've been curious if these have any issues on the really cold days? I know its been a mild winter so far. But if we get some cold temps a cold start video would be Wicked!!
@thekanemadness1 Жыл бұрын
Once we get some colder weather for sure. It does not produce near the heat the OEM does. I should have measure intake temps prior. I wasn’t too worried as I have a webasto as well so typically any cold weather the truck is pre-heated.
@tommysalami308711 ай бұрын
Kickass. I have same setup. I also was tryin to figure out a hack for this, called banks and they had no insight. Thanks for the lesson.
@thekanemadness111 ай бұрын
Glad it helped!
@JacobLucas-z8r Жыл бұрын
why weld the bung vs drill out one of the holes already on the back? i was looking at both options..
@thekanemadness1 Жыл бұрын
Where the smaller holes are - that section is raised a few MM and if I recall the bung is just as wide, once drilled for the bung there would be a slight gap. The location allowed it to be a bit nice to tig in. Also being lower down is just less obvious to the eye. I’m sure you could put it there, but those are my reasons for choosing that location…!
@ekeltek Жыл бұрын
What is part number for the heating coil and where do you get it?
@thekanemadness1 Жыл бұрын
I don’t remember the exact part number. But BD makes one, banks makes one and the one I have is for a chev diesel. I’ll see if I can find it
@geebroni4118 Жыл бұрын
Would part 1S12230 work? On Amazon.
@thekanemadness1 Жыл бұрын
@geebroni4118 that isn’t the one I used but looks to be much the same.
@ratgreen9 ай бұрын
@@thekanemadness1 Is that coil branded? Like an OEM part or made by banks? I dont trust random Chinese pieces of metal in my intake so Id only trust it if it was an OEM or high quality part. Could you try find the part number please?
@thekanemadness19 ай бұрын
DIH4 is commonly what is used as part number to find these. There is a multitude of parts manufacturers that make them. Take your pick of who is reputable and who to choose from. These were common in Chev’s LB7 engine from the early 2000’s.
@ratgreen9 ай бұрын
I'd be interested to know how much this little coil actually helps. A cold start comparison on two different cold days of a similar temp would be interesting, one with and one without the coil. Thanks for the vid.
@thekanemadness18 ай бұрын
For sure it helps. The factory heater does do a better job of pre- heat. But this works ok. Where I am from in winter, cold climates I don’t just rely on the pre heat. I run a webasto coolant heater to help eliminate those cold starts. But for peace of mind with factory grid heater, the coil gives that. Cheers!
@dodgedude9089 ай бұрын
That air temperature sensor extender you mentioned, even though you just lengthened your factory wiring you happen to know a part number for the extender or no?
@thekanemadness19 ай бұрын
Fleece makes one and so does Banks. Fleece part# FPE-HAR-67-IAT-EXT
@jaysonarmenta2255Ай бұрын
I’m getting ready to install the same heat coil. I’ve heard stories of it frying the electrical system because it grounded itself out, I was wondering how you did it and if you had any problems with it? Thanks
@thekanemadness1Ай бұрын
It is one terminal to install. Route your cable and secure it, shouldn’t have an issue. Less fail points than the OEM heater. I did put a little shrink tube as a boot over the terminal to keep the power cable as isolated as possible. Cheers
@coreyadams46467 ай бұрын
Great video, will I need an air temp extender for a 2012 6.7l Ram. All I see are for the 2013-2018s. Thanks
@thekanemadness16 ай бұрын
I think it would be the same unless the connector is different or the sensor has changed locations. But I can’t confirm what you’re asking!
@coreyadams46466 ай бұрын
@@thekanemadness1 Finish, wow what a difference. So on my 2012, my air temp sensor is located in the same spot as original, didnt need to extend. I also did the bung technique with the aluminum weld. Added a heater just like yours and works great. Thanks
@cjwickie Жыл бұрын
best fix ive seen.
@mediajunkie2195 Жыл бұрын
My Mega Cab 4X4 G56 still has GH. I'm at 335000 miles (540000 or so Kilometers). No issues but feeling this needs to be done. Delete pieces are AFE but factory grid heater still in tact. What product do you recommend to delete the factory GH plate? Also If I remove the power to the relay will this buy me some time? Oh BTW I'm located in the deep south of the US so 10F is the coldest Its been since I've been here.
@thekanemadness1 Жыл бұрын
If you wiggle the power source at the plenum and it moves that is a pretty good indicator there could be incoming trouble. Yes, you can remove the cable from the relay and then I recommend some shrink tube over the ends of the cable. For the plenum there is multiple options Fleece, Pusher, BD diesel and Banks all make a non grid heater plenum. I saved a few bucks and got one off Amazon. Which is much the same billet aluminum. I used an OEM Cummins gasket with it instead of whatever came with it. Works and functions great. Hope that Helps!
@bucketheadrox Жыл бұрын
Yeah my power cable blew up and as long as the bolt wasn't dangling and was tight when you pulled the cable. It should stay there indefinitely. I start up just fine in 21 degrees. 2 degrees over a couple days last year wasn't good but I have no in between yet. It's 40 again.
@PondstompingAdventures9 ай бұрын
How did it fair over our Alberta winter? Any issues with the cold. I have the banks gird heater delete, but havent installed it yet. I have the 3.5 inch intake horn, your video has given me an idea where to mount that coil heater. I wasn't too confident on drilling out the top hole on the banks intake horn.
@thekanemadness19 ай бұрын
It doesn’t produce like the stock grid heater by any means. It does ok though. My truck is usually always pre-heated too with a Webasto. But I have had a few real Canadian cold starts and it did ok. I liked keeping the coil out of sight, I like it better in the back side then on top.
@davidzaratee Жыл бұрын
How was this wired? Was it the same wire as the grid heater bolt?
@thekanemadness1 Жыл бұрын
Exactly!
@jacoblucas333111 ай бұрын
Hey im doing this exact thing but i cant find an aluminum bung anywhere. Any info would be great. Thanks
@thekanemadness111 ай бұрын
I found mine off Amazon. Search m22x1.5 aluminum bung. There is a few to choose from.
@seanriley3882 Жыл бұрын
Kane do you have part# for the monster ram air intake, and is that the 1000 cfm
@thekanemadness1 Жыл бұрын
Part # 42790. The bigger Banks horn with the 4” inlet on it
@everforexcanada56632 ай бұрын
great vid! just wondering what cleaner spray your were using to clean the inside? thanks!
@thekanemadness12 ай бұрын
Thank you! That was just some good ol fashioned brake clean
@15w1ck3d038 ай бұрын
I don't understand why Banks didn't make that an option with the heater coil on the non CARB intake elbows.
@thekanemadness18 ай бұрын
I wish they did something too. I do like having it where I put it on the back side, more inconspicuous there. Personally I like the clean and declutter of it!
@maddog8911capt3 ай бұрын
What year is your ram? And which Banks Grid Heater kit did you go with? They have two on their site, they say one is for 1st gen ISB 6.7 and the other is for 2nd Gen ISB 6.7, but I can't find anywhere to tell me which gen the ISB is in my 2017 ram 2500... Also, where did you get the vertical column heater by itself?
@thekanemadness12 ай бұрын
I just have the banks intake horn. The other parts I used aren’t made by Banks.
@williamvanmeter10709 ай бұрын
Nice video. Thanks for all the good ideas.
@palharley Жыл бұрын
Are you installing a larger heater than the one that comes on the Banks?
@thekanemadness1 Жыл бұрын
Same size as far as I know!
@logansaywhat834 ай бұрын
Hello Kane, Which coil air heater is this one that you installed?
@thekanemadness14 ай бұрын
Look up DIH4 for part#.
@mediajunkie2195 Жыл бұрын
Thanks for the video and again for you're response to my first questions. Were the fuel rail lines hard to break loose? I would think yes due to extreme pressures. Thanks
@thekanemadness1 Жыл бұрын
Nah not bad at all. Fairly easy to do I found.
@josephchalifoux7930 Жыл бұрын
I thought the top hole in the elbow was sized for the spiral wound grid heater. Maybe your Chev Heater has a larger outside diameter than Banks?
@thekanemadness1 Жыл бұрын
The intake for emissions intact is already set up to take a coil heater M22x1.5, it is also machined around the flanged for it. The non-emission monster ram like mine is not and is smaller. Diameter of heater same size
@clintonowens2001 Жыл бұрын
Hello sir awesome work do you have a part number for the bung
@thekanemadness1 Жыл бұрын
Search B09X4V8XLJ on Amazon. That will bring up the bung I used. Thank you..!
@devonjankowiak Жыл бұрын
Nothing of that sort comes up on Amazon when I type it in. Do you have any other leads on finding one? Thanks
@thekanemadness1 Жыл бұрын
I’m in canada so use Amazon.ca. May not be available for Amazon.com ??
@devonjankowiak Жыл бұрын
@@thekanemadness1 man that did the trick and there was literally 1 left! Thanks a million!!
@mitchell06167511 ай бұрын
What wheel are on your truck?
@thekanemadness110 ай бұрын
Cali Gemini 24x14
@josemc0628 Жыл бұрын
Thanks for the video I’m thinking about doing this my self . It possible u can get the parts number or links for the parts I want to do the banks monster 4” do the Grid Heater delete.
@josemc0628 Жыл бұрын
I also live in Houston Texas too be exact it don’t really get cold here. But prefer too have that piece off mine that 10mm nut won’t brake and damage my engine thanks
@thekanemadness1 Жыл бұрын
I used banks part #42790 for the horn and sourced everything else individually. If you want whole kit banks makes part# 42798 if it is for 13-18 year models.
@DOC6.79 ай бұрын
What year is your Cummins?
@thekanemadness19 ай бұрын
2018 sir
@DOC6.79 ай бұрын
@@thekanemadness1 thank you.
@DOC6.79 ай бұрын
@@thekanemadness1 I only asked cause you drilled in your intake for the coil heater. I have an 18 also and my banks was already tapped. My friend has a 14 and banks don’t make it with the coil heater tap. So I sent him your video to show what you did. Thanks again.
@RogerM1978 Жыл бұрын
I did a grid heater delete 2 yrs ago but I need a heater plug now but can’t remember what wire went to heater please make a video to help a clueless shade tree mechanic
@MechanicalMercenary10 ай бұрын
Battery cable coming from solenoid on passenger side around the front of the head.
@herculesinwyoming Жыл бұрын
I have never seen a grid heater bolt fail. I know it happens , I think it isn't near as common as people think.
@bucketheadrox Жыл бұрын
But it is always overvolting. So it's always getting the treatment that could cause it to fail. Mine exploded from the outside cause my connector failed before the bolt. I'm still gonna get a non grid heater plate and just tap my intake for a coil.
@thekanemadness1 Жыл бұрын
It happens. For the cost it is safe assurance to not have it happen. With wanting to add the bigger intake horn…clean up engine bay - for me it made sense to go this route!
@herculesinwyoming Жыл бұрын
@@thekanemadness1 mine is already done. Still never seen one fail
@mariodiy4517 Жыл бұрын
Most end up failing out of warranty. Even if it was during the warranty period, RAM will use the same parts. RAM does not have an upgrade/improvement on this.
@petermandel25529 ай бұрын
It not common until it happens to you. $$$$$$$
@rocksolid180411 ай бұрын
THE MOSTER RAM IS A BIG POWER UPGREADE WITH GRID HEATER DELETE