Guida alla riparazione della vernice - Parte 5 "Riparazione danni su parti in plastica"

[@valentinomuller3530]

Buonasera, ho seguito tutti i passaggi ma non ho messo il filler bianco. Il colore finale risulta diverso da quello della carrozzeria, nonostante sia quello giisto, dipende da questa mancanza? Grazie mille

[@emacod465]

Hi, which grit of sandpaper are you using in te beginning of the video to remove the trasparent and the paint?

[@presto_EU]

Good morning Emanuele, thank you first for your interest in our products. Here is the information you requested about the sandpaper grit: First sanding = P180 / Putty sanding = P120-P240 / Filler sanding = P 800 wet. Best regards European Aerosols Social Media Team

[@kimpoyvillanueva6253]

Ciao, quanto costerebbe una riparazione cosí in carrozzeria? (Verniciatura)

[@presto_EU]

Hello Kimpoy Villanueva, This varies a lot. However, it will be several 100 €. Best regards, Your European Aerosols Social Media Team

[@marybiscotti3330]

ti vogliono cambiare tutto il paraurti per un graffietto ------

[@davide4256]

Buonasera, avrei una domanda... devo cambiare i paraurti della mia fiat panda del 2012, sia quello anteriore che posteriore. Vorrei metterlo nero opaco come quando lo si compra, prima che venga verniciato. è sufficiente acquistarlo e montarlo essendo già nero o devo comunque dare un protettivo? ho visto molte panda col paraurti nero...

[@presto_EU]

Hello Davide, thanks for your interest in our products. Can you please write us in English, so that we are able to understand you or contact our company in Italy directly? MOTIP DUPLI ITALIA S.r.l Piazza Tirana, 24/4 I-20147 Milano (MI) Telefon [phone] Kind regards MOTIP DUPLI Social Media Team

[@davide4256]

@@presto_EU Good evening, of course excuse me ... I have to change the bumpers of my 2012 fiat panda, both the front and rear. I would like to put it in matte black. online I saw that they sell it black with the primer on it ready to be painted. is it enough to buy it and mount it as it is already black or do I still have to give a protective? I've seen many pandas with black bumpers ...

[@presto_EU]

Hello @@davide4256, there are big differences in the quality of these pre-primed bumpers. Often this primer is only suitable for transport protection. We cannot therefore say whether you can drive with it in the long term. The only serious answer from us can therefore only be to paint the bumper properly, as shown in the video, for example. If you want a structured surface then you can use such a spray: www.motipdupli.com/it/ITA/lang/prodotti/colormatic/aerosol-stucco/verniciatura/ipg-1227.html Kind regards MOTIP DUPLI Social Media Team

[@davide4256]

@@presto_EU all right, thank you so much!! I Will try

[@petrusbenckey]

Quando si dà il fondo e quando il primer/aggrappante? Quel filler spray è uno stucco riempitivo, a cosa serve?

[@presto_EU]

Hello Fabrizio, thanks for your interest in our products. Can you please write us in English, so that we are able to understand you or contact our company in Italy directly? MOTIP DUPLI ITALIA S.r.l Piazza Tirana, 24/4 I-20147 Milano (MI) Telefon [phone] Kind regards MOTIP DUPLI Social Media Team

[@presto_EU]

The following instructions will help you to achieve the best possible result: 1. sand the damaged surface. The surface must be clean and free of grease. Remove traces of silicone and grease with DUPLI-COLOR Silicone Remover. 2. Apply presto Plastic Filler to the damage. This filler remains flexible even when dry and does not break when exposed to light loads. 3. Sand the surface to level the filler and then clean the surface with DUPLI-COLOR Silicone Remover. Then prime with DUPLI-COLOR Plastic Primer to ensure adhesion of the subsequent coat. After 10 minutes drying time, prime with DUPLI-COLOR Filler and allow to dry. Sand again and clean the surface with silicone remover. 4. 4. spray several thin coats of DUPLI-COLOR AUTO-COLOR Acrylic Spray until the coat is opaque. The coats must be thin to avoid excessive film thickness, runners or drying problems. If necessary, spray over any spray mist in the marginal areas with a spray paint. 5. Metallic colours must be sealed with a protective clearcoat. For this purpose, you can use DUPLI-COLOR 2-Coat Clearcoat or 2K Super Clearcoat. If necessary, spray over any spray mist in the marginal zones with a spray lacquer.

[@lucaalmonte3550]

Sito per acquistare i prodotti?

[@presto_EU]

Hello Luca, unfortunately we don't have a webshop ourselves. But you can contact our colleagues in Italy directly. They can certainly help you: MOTIP DUPLI ITALIA S.r.l. Piazza Tirana, 24/4. I-20147 Milano (MI) Telefono [phone]. Fax [phone]. e.mail [e-mail] Kind regards MOTIP DUPLI Social Media Team

[@royjohnson6623]

Come agisce l'armonizzante?

[@presto_EU]

Hello Roy, can you please write us in English so that we are able to unterstand your question? Kind regards MOTIP DUPLI Social Media Team

[@namelessgirl0022]

Quanto potrebbe costare un lavoro del genere ?

[@presto_EU]

Hello, unfortunately, it is difficult to make a statement. It always depends on the size of the damage and the corresponding use of materials. Kind regards European Aerosols Social Media Team

[@lucaluca1297]

Eeehhh sto czzziii sei un carrozziere? 🤣🤣🤣

[@presto_EU]

Hi Luca, can you please write us in English so that we are able to understand you? Thanks! Kind regards MOTIP DUPLI Social Media Team

[@carpipazzo]

Se lo portava dal carrozziere avrebbe speso la metà, con tutti i prodotti che ha utilizzato 😂

[@lucaluca1297]

😁😁