GY6 Taida T100 Camshaft valve adjusting How to 190cc 07

[@larrykeesee1442]

THANKS DAN FOR ALL THE GREAT INFORMATION.U HELPED ALOT OF RIDERS...

[@alanfoster2271]

Hi Dan you say set the intake gap is wider than the exhaust! But you set the intake gap smaller than the exhaust ! And i went back twice to check what you had said ! But thank you for the video it was very helpful

[@claudio67362]

Daniel,have you tried installing a regular 157qmj head on a 1p57qmj.i would say it might be ok since the difference is very small.Will the chain tensioner make up for the timing chain slack?

[@dwayner2518]

I have a 150cc GY6(1P57QMJ), the flywheel has exact same markings as yours, however when I set TDC by using a dowel through the spark plug hole the first line before the T is approx. 10mm past the alignment mark on the case? at this setting my camshaft marks are slightly off by one link, if I set TDC by the T mark method the camshaft is in alignment but the piston is not exactly at TDC, it is slightly before. I may be wrong but I'm pretty sure the camshaft alignment should be done when at TRUE TDC by using the dowel method, I can't help but think the engine timing is set one tooth out from factory.

[@FranklinHicks-qs4gs]

I experienced that as well. Did you find a solution

[@Yakplanet_tv]

Question? I have new a9 cam and installed them in on a big bore kit. But when I tried to adjust my rocker arms. They seem to have a much of a gap. A little too much gap where I can't even adjust them. My cam lobes are facing the motor. And when I out on the rocker arms they have too much play. So I flipped the cam over and I was able to adjust them.

[@seanmayo206]

What if the chain link doesnt match from the factory? Move chain?

[@deschuyteneerpol8372]

very instructive thanks. Do you know about a camshaft with an automatic decompression system ? It is for a bailey engine V5 (GY6)

[@maninderthind4309]

Hi bought V5s last year.

[@anishilmiahmadbadri3868]

Thanx. Great information i got there.

[@Knowledgefiend]

How many pounds on the torque wrench ?

[@kaw73]

What your opinion on using the taidia T-one cam in a A block with the taidia 61mm drop in kit , it currently has an a13 cam and tops out in the low 50s at a max rpm of around 7k , while I love the low end torque ,I'm hoping this t one will be good fit all round , in a hypothetical would you change the cam lol , 30mm cvk style carb and aftermarket pipe ,running a tad rich, please it only hypothetical now lol

[@b-wiser3636]

Nice video what’s your charge for install 171cc on Chinese 150cc?

[@henkvandermerwe8990]

HOW DO YOU FIT THE TIMING CHAIN GUIDES thanks

[@ipray4yousmc]

What was the torque wrench on that an if it was a two stroke what would be the torque on a 1E40qmb 49cc I just ruined mine used foot pounds 10 now I'm told I need inch pound's like 130 I got a couple of two stroke engine's but I just got a 150 and I like your video's but the 150 is for a gocar I can't put brakes on it and I no if I could wield it.

[@لطيفالحلفي-ح7ض]

motorcycle Honda spacy 100cc. intake 0.05 . Exhaust 0.06 . What do you think.

[@justinxityzamudio1388]

Hello from México good video thanks David Martin 4 this vídeos

[@blackjuice007]

Wish you can talk about and show the cam shaft lobes..

[@worldcollections2839]

Please I need your Help : I have set up a new gaskets for my GY6 150cc then after all that : I turned on the Scooter on the idle screw without opening more gas. but it works not regulary : while it is in the kick stand the rear wheel stops then moves slow then a little speed then stops the biggest problem is that the sound of the scooter is like AK47 Rifle you can hear it from 500 meters away . I suspected the Stator or Spark plug itself then the Gas Mixture screw maybe need to be closed a little : also I suspect that the Exhust need a New Gasket to make the soun lower ,, please tell me what is that Problem ?

[@Mech.E]

Did you solve it? What was it

[@b-wiser3636]

Big bore kit?

[@proteusmacapagal1453]

sir its that okay to use stock camshaft without camshaft stopper plate?

[@tobysuttles9559]

Hi I have a 161QMK I got it from scrappydogs I was wondering if I could put a 63 mm piston in it without half team to board it out

[@Gy6HackPh]

Why you're whistling? Nice video!

[@b-wiser3636]

How do I contact you for service on my 150cc ??

[@jamesroberts95]

That is the reason I build my own stuff because I sure wouldn't let u work on my stuff that is for sure

[@3628778]

Would it be possible for you to help with my scooter

[@mopedman8220]

09:32 "intake always larger than exhaust" sets intake to 0.05 and exhaust to 0.07 ?????????????????

[@Mech.E]

Exhaust valve should have bigger play then intake valve. It's because it heats up more, so it expands more. I think he mis spoke

[@jamest.5001]

Yep, he backwards said it. The exhaust is looser because it gets hotter and expands slightly, and will be approximately the same as the intake when hot!

[@youtubeuniversity6589]

Hey do you have a way to get a hold of I'd like to have you build a engine for me

[@DrLove911]

I build engines this guy is pretty good tho. I've probably built 70 engines before I started watching this dude and I still learned some shit. But I build racing Gy6 engines and even supercharge them.

[@b-wiser3636]

@@DrLove911 hey I have a 150cc do u have info to reach for service on upgrading my motor??

[@MrWeaponlord]

Why not insert the dowels where ever possible?

[@jacobtucker6819]

I just need hes help with my

[@AugustosSilva]

thank you

[@jeromecollins4422]

I dont get it

[@789costela]

you got new nuts ? EEWW wath ? 😕😂

[@bobbydinkel7051]

You make me nervous

[@noneshere]

Theres pure nitrous oxide in a can of whip cream. It dont stink like the track tho 😁

[@Cito_Fiytb_617]

@@noneshere huh?

[@davidhill588]

This was painful to watch