GYROBALL || Teardown

[@AvidiaNirvana]

I'm pretty sure those are inductors not capacitors, even though they look very similar to electrolytic caps. That would explain how it generates the electricity that powers the LEDs. So the "sensors" are the two inductors that generate electricity as the rotating magnets pass by.

[@PremYt-m4b]

Tanks for explaning the working off the gyroball. I was wondering it, and googled it, and that's how i end up on your film. 👍

[@crieliocriel]

Thank you!!!

[@drago7598]

I have almost the same exact model of Gyro ball minus the lights and thanks to this video. I was able to repair my exercise Gyro ball. Thank you so much.

[@meandmykuttus2574]

Mine is vibrating so bad when i start to spin it plz hlp

[@crieliocriel]

how bad is the vibration? because small vibration is part of it.

[@meandmykuttus2574]

@@crieliocriel it vibrates so much

[@crieliocriel]

@@meandmykuttus2574 let’s see.. have you tried prying it open? And look if there are loose ends?

[@cnarefeorhan9321]

how do i fix it that could have caused it to drop it on the floor and then it didn't work at all

[@G8HCB]

L1 and L2 are inductors with coils, when passing through the magnetic field these generate electricity. L is for inductor where as C would be capacitor which they are not.

[@Masterof1ne]

Thank you! i have been wondering what it is going on inside!

[@crieliocriel]

my pleasure!! Thanks for dropping by!

[@KongKingman]

Mine came with a lanyard like yours Im dumbfounded where can I insert it, there are no holes in unit to insert

[@crieliocriel]

you can just poke a hole on it.

[@KongKingman]

@@crieliocriel thanks for that info, but idk why they would include one and would expect one to alter the device ?

[@crieliocriel]

@@KongKingman might have been a manufacturing error which QC missed. If they do have the QC.

[@KongKingman]

@@crieliocriel thanks for reply. I since bought the “gyro stick” you put the gyroball on a “stick”

[@xSO20]

What to do my gyro ball is not spinning after I cleaned it. What do I need to do for friction?

[@crieliocriel]

you can add a bit of oil,

[@xSO20]

@@crieliocriel mine doest have any plastic ring in between the case.

[@hafiznahri5365]

Just want to ask,the small white ring where to put?

[@crieliocriel]

I think it is place in the middle before putting back the two parts..

[@Agylrs]

It's the nut that secure the clipper with the mechanism.

[@baboigames5374]

Tried everything won't open not with screwdriver throwing it knife spoon mine fell and now not works properly thats why i am trying to open please suggest

[@crieliocriel]

i just pry it open with flat screw. you can see the latches?.. try to open it at that part.

[@baboigames5374]

@@crieliocriel heyy thanks I opened and figured it out but don't know how to fix it my gyro ball moves left and right and makes a "tack" sound the steel rod the holds it is moving

[@nooralbyati]

Pls .. why does it sound increased and became louder than before .. much louder !!!Should It be greased?

[@crieliocriel]

yeah.. probably you need to do that.. just try it..

[@nooralbyati]

@@crieliocriel It didn't work .. grease made the movement hard

[@crieliocriel]

@@nooralbyati how much you put? It should be just like 2-3 drops

[@nooralbyati]

@@crieliocriel believe me not a single one

[@annoymousannoymous9439]

Help,i cant crack it open, i used flat screw, knife, nails and all failed

[@roho8380]

Why the spring doesn't work if it's upside down?

[@crieliocriel]

what spring?

[@roho8380]

@@crieliocriel the arch, el resorte, la cuerda, the mechanical initial impulse.

[@BMG_TON]

3:48 tôi ko cần tua nhanh

[@jorgeochoa1811]

Cómo lo abriste?

[@madmawsupreme]

Take of rubber , and pry it open with flat head anywhere in middle seam

[@socialwagner]

this guy speaks with one word / year!

[@danielacoelho4795]

I enjoyed the video. But please don't speed up the parts where you disassemble and assemble, they are very important too. Thanks!

[@crieliocriel]

noted mate!

[@choilucas2333]

I saw ur video and im wondering how u managed to pull the ball open agter unscrewing it cause i tried what u did in the video

[@crieliocriel]

you need to use flat screw to punch through to it a little bit.

[@azrael7029]

Bro I don't know if you are professional at these stuffs but I want to tell you that those two black things you calling capacitors are not capacitors, its the electromagnet and the other thing that fits beneath it and rotates is a magnet and when it spins the electromagnet absorbs the electromagnetic feilds generated by the magnet to power the led. Its a simple thing but is created greatly. And the heavy thing that rotates is the actual gyroscope.

[@matttwelve7332]

Why you speed up this so bad 😂

[@crieliocriel]

hahaha.. i figured.. =))

[@betty5948]

Tysm

[@jessa.3857]

Does the all metal gyro ball come with a metal track for the gyro to spin in or is it plastic?

[@madmawsupreme]

Plastic

[@brucerulz5297]

There is no sensor. It’s an electro magnetic generator

[@JenniferThomas-z7l]

Walker Betty Gonzalez Richard Garcia Jennifer

[@Tazywz]

Mines don’t light up😢

[@leandroprates3634]

ele não mostra direito

[@petervick4775]

Useless! The most important part of the disassembly and you have speeded it up so that it is IMPOSSIBLE to see how to take it apart! What an utter waste of 10 minutes of my life!!! After removing the 2 screws (one each side) of the midway point HOW do you separate the 2 clear plastic halves to open up the insides?????

[@crieliocriel]

i am sorry if you feel that way.

[@GarenNileshRaviChelliahDunmans]

Bloody hell scammer of her is this true