Hacking an ebike: how to reprogram the Bafang middrive

I go through some of the change i have made to my ebike programing to get the bike to perform the way i want it. Many popular commercial bikes also use Bafang motors and may be fully reprogrammable as well.
Link to another video where i show how to reprogram an Ebike using an Android App
• Hacking an Ebike with ...
Link to Bafang programing cable
amzn.to/3B7Impv
amzn.to/3XwuDQh
Link to Bafand Mid Drive Kit
amzn.to/47xoGr5
s.click.aliexp...
s.click.aliexp...
Link to software and good guide to read
edrivenet.com/...
Tools i use
ISDT 8S battery Monitor
amzn.to/3kwiqY5
ToolkitRC 8S charger
amzn.to/3dSxMon
icharger X8
amzn.to/3pXGAfa
Bench Power Supply
amzn.to/3sETf8n

[@JamesCampbellMr]

I think I can honestly say I think this this the best tutorial I've ever seen on anything on youtube, ever. So refreshing!

[@mikeking245]

this guy smoked it

[@Ariel-lt8ln]

Great tutorial and I say this to you with love, were you high?

[@ahmadahtezaz1408]

Indeed

[@johnwoodward7908]

Great Video. I did have a 250 watt bafang but upgraded to the 750 watt. When I first tried the bike it was far to fierce in in the lower settings. Your settings are perfect in the 1 - 5 almost exactly mimic how the bike was with the 250 watt motor and 6 - 9 make the most of the extra power.

[@sp4c3g]

JEEEEEEEEEESUS are you telling me that phisically 250W and 750W motor are the same? is just software limited??

[@stevenc22]

No. The 750w and 1000w are the same

[@ducksgoquackirl92]

@@stevenc22 NO they are not.the 750w is the BBS02B its limited to 25amps, the 1000w is a BBS03 (BBSHD). the bbso3 has larger core motor windings and its controllercan take upto 30amps before you get magic smoke.

[@RC-io9jv]

This is a good video for showing how to re-configure the settings... Thank You ! These modifications were just the ticket !

[@MrScaramoosh]

The gear shifter makes it a lot smoother and has natural peddling.

[@StephanCzajkowski]

i'll save everyone the hassle with finding the driver for the cable, take a magnifying glass (if the usb plug has clear heatshrink) and look at the code on the black chip, mine is ch340, spent 4 hours, once i found that it took 2 minutes

[@Full_Throttle_no_Brakes]

So where is the link?

[@StephanCzajkowski]

@@Full_Throttle_no_Brakes if you can read you don't need a link

[@lilcool6830]

What’s the black chip

[@lukeo85]

Also took me 2 minutes thanks to this comment. 😁👍

[@BROWNDIRTWARRIOR]

Hey man, spent 40 bucks on the Bafang programming cable but when I plug it into my computer I don't get anything other than the sound of the computer recognising the device. Is this a driver issue or should I be getting a pop up menu? I have a Juggernaut 1000w mid drive. Thanks in advance.

[@marcinmachnik9787]

by far the most concise and informative i've seen so far. great work.

[@stevenc22]

Thanks!

[@marcinkopa]

@@stevenc22 Hi, could you make a video about the free Speeed (3 letter e) app for configuring Bafang BBS series motors (and most Hub motors). It is the equivalent of the popular windows tool but in a robust phone version with bike display functionality and 25 language versions. thank you for a great job!

[@stevenc22]

@@marcinkopa I cant seem to find it in the app store?

[@marcinkopa]

@@stevenc22 Unfortunately, at this time only Android phones/tablets are supported (iOS does not support usb-uart adapters). The good news is that an advanced and ridiculously cheap bluetooth module is in the final stages of development, and an iOS version will be coming along with it. github.com/mkopa/speeed

[@stevenc22]

@@marcinkopa I use Android. Just ordered a otg cable. I'll check it out

[@lennymiller7336]

This is a great video for tuning your Bafang. The mild settings are perfect for my wife and has enough reserve power in the upper levels. Thanks, good job!

[@stevenc22]

Glad to help

[@lennymiller7336]

I’ve heard that you can configure these to work more like a torque motor, any idea how you would do that? I bike for exercise but at 71 with 4 back surgeries and 2 hip replacements I’m slowing down, I can only go 50 miles on a trike and I’m whipped. Thanks

[@stevenc22]

@@lennymiller7336 Lenny, what do you mean by "Torque Motor"?

[@lennymiller7336]

From my understanding the BBS02 is considered a cadence motor and a torque motor provides assist based on how much force you put on the pedals.

[@stevenc22]

I see. Yeah the Bafang doesn't quite work like that but you can easily program all the different assist levels to get the right amount of assistance so that you still get a good work out.

[@MathieuTechMoto]

Extremely useful information, thank you !

[@Vilisith]

Just a heads up. Depending on where you buy the cable and the cable brand you will end up searching online for compatible USB drivers before Windows will recognise the USB com port. But once you have done that it works like a charm

[@nathancarra6134]

Thanks for the video was very helpful, I copied your setting and it made an amazing difference thanks again.

[@RobertAdams-ly5ku]

This is the best guide for programming the BBS02, on KZbin

[@griznbeer]

This is so dang cool!

[@bartbaddie347]

Afterthought . . . if you were to revise the video, please highlight that . . . it's the motor/controller that decides when to pedal, not simply the rider. E.g. if you stop pedalling when approaching a Stop (with 18-wheelers rushing past at 100km/hr ) and you click down a few cogs in preparation to pull away . . . and turn a few pedal strokes to ramp the chain to the cogs, you can get a sudden surge in power . . . into the 18-wheelers.

[@robwood3976]

Thanks for the info, I have 2 bikes with Bafang middrive's, they're both 350w 36v units but they perform differently. Your info should I hope enable me to get them both the same. Thanks a lot, Rob

[@kevinjohnson8792]

Thanks Steve,i just hand to replace my controller due to battery reporting issues and the throttle wasn't grunty and it was too fierce off the line on ped 3

[@MeysamShojaeeNejad]

There is a Mode in Bafang motor called 'waking'. By keep pushing the minus button it get activated and the max speed will be around 5mph. I admit that 15 mph is too much for level 1, anyway.

[@trevorselch5574]

This is fantastic. Thank you

[@benjaminberger9629]

I've reduced the two Start Current to 1%, was too jerky for me at the start.. much smoother now also Slow-Start mode is the time it takes to ramp up to full current, the parameter you are describing is Start Degree (How long it takes for the motor to react when starting to pedal)

[@stevenc22]

No splitter cable. Plus it's best to make small changes at a time or else you can mess things up. Just start with you stock tune and tweak a few things that annoy you.

[@JEVVJITSU]

The first cable i bought did not work. It would be recognized by my computer and show up in the com port but it could not read the controller to show any info. I ordered a new one from a different vendor and it seems to be working. I have a 1000w motor with the 52v 19.2ah shark battery. Anyone have a video or post about fine tuning the same setup? 29' specialized rockhopper 2015, btw.

[@greybruce714]

Thanks Steven for taking the time to make this video. It is an excellent source of information for me. I’ve got a Bafang 500w mid motor on my TerraTrike. I would like to slow it down in general. I am a little uneasy thinking that if I did something wrong I might “brick” my controller. Is there a feature for controlling the headlight/display function? Right now when I turn the headlights on in the daytime the display automatically dims so much that I can’t read it. Also, it would be nice to just have the headlight come on when I am riding as a safety feature. Thanks again!

[@stevenc22]

Bruce not sure about the headlight but try it out. Pretty much impossible to "brick" it

[@Olafmacsambo]

Mentioning gear setting would help.

[@aNDy-qh1em]

That you for clear explanation! Very helpful, endeed! Subscribed.

[@adeharris4457]

Great explanation of the spped settings but your wrong about the 1k motor the 750 is 24A & the 1k is 28A controlled but I agree to keep it lower anyway as the cooling on the motors is insufficient for full voltage to the controllers

[@ManMan-b5y5c]

I've set mine to 1 in slow start mode and it still doesn't kick in until I have at least 3 cranks of the pedal what's going on

[@ps99m]

does this work on the bafang m420?

[@stevenc22]

Models with a round connector for the screen work. Models with triangle connectors for screen do not work.

[@cd78]

Superb explanation

[@whiteXT]

My was factory set to 24. Goes good bends the high cog good

[@crispy-k]

Bought a bb02b 750w a few weeks ago and it runs great, but i was curious as to how it was setup from the factory. So i bought the usb adapter and got the software. Mine was set to 24amp as default, and max is saying 24, not 25 like most out there. Anyways i changed it to 20 just to stay on the "lower" side of things. Thanks for the video ;) Reading tutorials is one thing, seeing how it's actually done and be able to just "copy paste" is a lot easier ;) 10/10

[@lilleniyo5743]

How fast does it go? Have the same thing

[@crispy-k]

@@lilleniyo5743 With just the accelerator i can go around 45kmh on flat if there's no wind. If i pedal i can go 50 on flat. I already have over 2000km on it, and no issues so far, no weird noises or anything.

[@desertweasel6965]

You can also get a otg cable and do this on your phone.

[@stevenc22]

Yeah thanks. I made another video about doing it on you phone 👍

[@whiskeykilmer1866]

Thank you for this video. Very informative.

[@boccatxrx5023]

Mate, if you can find a hack for the bloody Bosch gen 4 motor you will make a LOT of people very happy.

[@stevenc22]

The newest bafang motors are no longer hackable. Damn manufacturers making life difficult.

[@boccatxrx5023]

@@stevenc22 yeah, its total bullshit. If i wanna go 40 thats my business, not the bloody bloke who sold me the thing😡 Plus they're clearly built to fail on top of it all...

[@espressologica]

Hi there, great video, can the m600 be programmed with your cable. I have issues with too much speed like you. Especially with take off. Thanks. Annmaria

[@stevenbronstein4686]

I know it has been awhile since you posted this but I thought I would try anyway. Great tutorial. I was hoping for some clarification. You suggested setting the throttle maximum to assist level 8 so you don't blow out the motor. The power is set to 100% on the previous page so wouldn't it be throttling at the same level ( 100%) as level 9. Thanks again

[@All4Grogg]

His current limit on PAS 8 is 80% of 18 amps, quick math; 18 x 0.8 = 14.4 amps max current; On a 48v battery system ; 14.4 x 54.6v = 786.24 watts @ full battery, 684 watts @ 47.5v 50% battery and 622 watts @ 43.2v 11% battery which is when the walk assist function should be considered to preserve the battery.

[@markdunford1497]

Great tutorial butI I have a mac. Is there software out there that I can install on my mac?

[@skatygarcia3096]

Hello. Can this process also be applied to my Engwe bike, which has an unbranded motor? I definitely want to try it. In the Engine Pro 2.0 model, the motor cuts off power after 28 mph and continues only with pedal power. Is it possible to remove this limit, or more precisely, to make the motor continue to assist the pedal after this speed? Have you tested this software on motors other than Bafang? Thank you.

[@skatygarcia3096]

I will do it for you, sorry. :) "Depends. Not whether your motor is bafang but whether the controller box is bafang. Many companies use bafang motor but their own proprietary controllers."

[@LimeXize]

brake lever or brake sensor? what to order?? I have mechanical brake sistem on my bike. PLZ HELP

[@stevenc22]

I use sensors. I wanted to keep my original brakes. The sensor just sticks to the underside of your brake lever.

[@phd9590]

Mr. Steven, is there also some magic soft suitable for bafang hub rear motors such as H400b 250W 36v. I got such with can bus and speed limit of 25km/h. Using DZ41 (speedometer) I was trying to change it but it seems that it's locked in controler by a vendor. I was thinking about BESST but have no clue it will work. Rgds.

[@stevenc22]

The problem with rear hub motors is often the hub might be Bafang but the controller is a completely different brand and then you cannot use the Bafang tool to reprogram.

[@skatygarcia3096]

I could't find any software for rear hub motors. Can someone help please :)

[@capt.lennymiller6524]

Great tutorial but where do I get the program I need? thanks

[@stevenc22]

There are links in description

[@scallahan6426]

I purchased an Ariel 52V x class. It’s not a mid drive but a rear drive. The drive is by Bafang. I have the same problem with run away in PA. Doesn’t matter if you leave it in the stock 0-5 range or as Ariel says “change it to 0-9 and that will help”. That’s BS! Ariel says you can’t change the percentage on each pedal assist. I can’t try the programming cable you mentioned because its a female adapter going to the controller not a male. The only hope I have is that there’s a USB port on the LCD screen. If anybody has any suggestions or can point me in the right direction I would greatly appreciate it. Thank you.

[@rickdeckard9810]

7:33 Thanks for the great tutorial. You'd mentioned you wanted to override the throttle regardless of which PAS mode or gear bike was in, would there be a risk of damaging the components if you set throttle power to high?

[@stevenc22]

No but the tutorial does recommend not putting the throttle so the way to level 9 because going up hill and punching the throttle could overload the controller

[@goriverman]

I cut back the amps to 25 it’s rated for 30. Start at a 10 % and increases as you go up

[@yvesn58]

Steven, you didn't talk about the speed limit configuration. Can you configure it to override the limit?

[@All4Grogg]

Second tab "pedal assist", third drop down box. His reads "by displays command" which means he has gone into the "secret" screen on his display and set the max speed to his preference. I think you can use this drop down box to change the universal max speed at the controller or simply disable it.

[@davidanderton2437]

Same question, can you override this setting, or connect to the display to change it. In Australia most bikes are limited to 25km/h which is ridiculous.

[@henningdoring9531]

Great Video. I am thinking of running a throttle-only setup on my current build. Do you think it is even necessary to install the controller and sensors for this? If I do still require the controller, then is there a way to disable PAS while still allowing the throttle to sit at PA lvl 9 for example?

[@stevenc22]

You can disable PAS on 1-8 and then just program 9 to full throttle

[@KSPIRITS8]

Excellent video. Thanks

[@garyhoward4064]

Thanks. Are you implying that with a 25A controller, I can get the full 1000w power out of my BBS02?

[@impermanenthuman8427]

So the motors can be unlocked to run at higher speeds but now the other parts of the kit that aren’t rated for use at 1000 watts risk being burned out or damaged? So if all the parts on the except the motor itself were built for the 1000 watt motor then you could clock the 750watt motor up to its full potential safely?

[@stevenc22]

The kit can do 1000w. It's just software limited to 750w

[@mdweed1]

thank you, that's good information !!!

[@vHypnoticx]

hey mate im having an issue where no matter what i do i cant have the throttle work on 0 assist

[@stevenc22]

Did you manually assign the throttle to assist 8?

[@hossben]

WHAT ABOUT SPARTA AND BATAVUS ?

[@vsalvato53]

Hi, my new Accolmile City bike mounts a mid M200 Bafang motor, with BUS Can; I am told that Bus Can motors cannot be programmed... do you know if this is true? My aim is to skightky adjust the kevek of assistance on each of the 5 levels and unlock the speed limit (15 miles/h now).

[@stevenc22]

Yes the newest motors cannot be programmed. However you might be able to unlock the top speed by going into the secret menu on your bike display. Google which display you have and how to enter the secret menu

[@syr_jeff1753]

Great Stuff Thanks !

[@bizeb3927]

does it work on bafang hub moter

[@stevenc22]

Maybe. If you have a bafang controller box it might work. But many hun motors use aftermarket controllers that don't work

[@AirbrushDGart]

Thanks for this video. One question though. If I set setting number one to 5km/hour will the motor start when it reaches 5km/h and will it also cut of at 5kmh? Second question, when using throttle can you pedal at the same time?

[@brianeustace4175]

Not if you`re lieutenant Dan!

[@impermanenthuman8427]

What about the 250 watt limited motors? Are they also capable of being unlocked up to a greater potential or will that also likely risk damage? A seller told me that with the 250 watt Bafang kit, that all the other parts other than the motor itself will work with the 500 watt motor, so theoretically in places where motors are limited to 250 watts, someone could fairly easily swap out the motor for a 500 watt motor and take the bike off road out in the backcountry and use the extra power to carry gear, then swap the 250 watt motor back in when you want to ride the bike in public again? Legally the motor must have 250 watts written on the motor to be street legal where I am, but if the 250 watt Bafang could be unlocked up to a higher potential safely without needing other higher rated parts which would normally come with a higher rated watt motor then that is very interesting is genuinely safe to do and the motor kit stays equally reliable ?

[@impermanenthuman8427]

In fewer words, what wattage can you safely unlock the motors up to that are factory limited to 250 watt for local road rules? Can they also be clocked up to 1000 watts or just 500? Thanks again

[@stevenc22]

I don't know much about the 250w version, but after a little googling I think the 250w version has the 350w controller on it so you can likely overclock b the 250w version to 350w. No more.

[@MumfordJim]

I think the AMP setting on the 250 will be much lower. Something like the range of 10-15. What every the original is maybe 15? Do not go beyond that. You are only asking for trouble.

[@freddore7885]

Great video, as you experienced, my Bafang was quite strongly powered out of the box. I was able to follow your instructions and make changes to soften the power at low assist levels. But, then I find my display, a Varstrom touch screen is allow only 5 levels of assist. I've explored all the setting and everything I can find, but can not find the option to change from 5 to 9 levels of assist on the display. I've encountered a "pass word" option. However, I don't have a password and the instructions that came with the system are quite brief. Do you have any suggestions about the assist level option on the display, and/or how I might get through the password setting, change or whatever... Thanks Fred

[@ARTSPECK]

Try 0512 password

[@calvintanner7897]

What cable would I need for the Bafang C961 controller, and where can I buy this cable ?

[@stevenc22]

the C961 is your display, not your controller. You need to check which Motor you have to determine if you can use the reprogramming cable or not.

[@calvintanner7897]

I 🤔 I'll know exactly what's going on as far as the controller, the motor, and the display as far as reprogramming. Thank you for your help.

[@mclainstaxc198]

Nice.good to know... I have one question in my mind. It is Necessary to install a gear sensor? If you have, how it affect the performance ? Thank you..

[@stevenc22]

I do not have one. A gear sensor isn't necessary as long as you let off the throttle between shifts to reduce the load on the drive train

[@mixerfistit5522]

I have one and it functions perfectly and I don't really notice it, without one if you fail to stop pedalling when shifting you will snap your chain pretty quickly If I hit a bump it'll sometimes activate briefly though, so maybe something to consider if you're riding trails

[@naimi9584]

Initial response: Got this bike for my friend. kzbin.infoUgkxUiL0GnyDjP32RJdd660sP8mZk4CRLTCJ Delivery was fast. And the friend was surprised I would order it when she had never suggested she wanted anything but the pedal bike she had. She has now ridden the bike two times and gives it a 10 and says it is very fun. We have some hills in our town that are very challenging to climb on a typical bike. But tonight she went up with the pedal assist and loved it. I was way behind on my standard bike, huffing and puffing. Now she is no longer lagging behind me. This thing is powerful enough that a person could go around town without any pedaling. She likes to get some exercise so on flat ground she hits the red button to turn off pedal assist and only uses the twist throttle when she's in a tough spot. The bike looks good. It is really a very nice bike for the friend. Now for me, when I get an electric bike, I'm twice her size and will be looking for a bigger watt motor and battery. But this one is just wonderful for my friend. I am happy with this purchase.

[@ManMan-b5y5c]

What does double signal 24 mean in the pedal assist page.

[@stevenc22]

Don't know but the instructions say that is the only option that works. So not change.

[@ManMan-b5y5c]

@@stevenc22 oh i changed my to DH12 i thought it had something to do with the type of Candace sensor you have but maybe in wrong

[@ManMan-b5y5c]

@@stevenc22 I did change it and my bike works is something to do with what kind of pedal sensor you have maybe.

[@ManMan-b5y5c]

my motor is a bafang rear hub 48v 750w motor with LB-AK-001 controller and is programable

[@marcusmarvin01]

The plug of my mid kit drive is green but not round, it's more like a triangle shape... What can I do? Can't find the right programming cable... I have an m300 bafang belgocycle

[@stevenc22]

The newer kits with the triangle plug are not easily programmable. Bafang changed the communication bus and the newer style hasn't really been cracked yet

[@marcusmarvin01]

😭😭😭

[@marcusmarvin01]

​@@stevenc22 there's a usb plug on the left side of the screen, no way to use it?

[@stevenc22]

No those are dumb USB plugs for charging your phones only. No data

[@GR14702]

Is this also possible with bafang M200?i want to increase themax speed.

[@Thefakisgoinon]

I have the BBS01B (36V 250W). It has current limit set to 15A. Can I change it to 20A?

[@stevenc22]

36v at 20amps is 720W. Way too much for a 250w motor

[@Thefakisgoinon]

@@stevenc22alright where is the cutoff?

[@sledking1236]

If you program it does that void the warranty?

[@stevenc22]

The program is direct from the manufacturer. So just using it won't void the warranty. However if you over amp the motor, that could void the warranty

[@josefonseca1547]

Hello! This cable and softwear works on a rear motor hub Sutto (Bafang) 48v 1000W? Because my PAS not active the motor

[@stevenc22]

Depends. Not whether your motor is bafang but whether the controller box is bafang. Many companies use bafang motor but their own proprietary controllers.

[@mennopieters3512]

Can you lower the torque settings somewhere i have a belt drive but its recommended max 80nm torque but i want the bbshd on my bike

[@stevenc22]

Sort of. You can reduce the power ramp up which is the equivalent of reducing torque

[@mennopieters3512]

@@stevenc22 thnx

[@kenchow6741]

I purchased a bafang, bbs03 HD motor December 2021, The newest motor cannot be reprogrammed

[@stevenc22]

Triangle connector can not be programmed.

[@tempusfugit6820]

Awesome information!! Is there a setting for getting the motor to disengage right away when the pedals stop?

[@stevenc22]

Honestly there probably is but I haven't looked for it. Check the two guides I linked to, they are way more in-depth

[@benythjet]

Stop delay under pedal assist tab

[@ויקטוראילוביץ]

Hello Great video, thanks. I have a bafang 750W 20 A, which functions very well but keeps getting error notes: code 30, code 10, etc.... Have you encountered this and know what to do? Maybe it's a display problem (c961), is there a way to reset it to the manufacturer's default?

[@stevenc22]

Code 30 is a communication error. Code 10 is an over heat error.

[@rytiss]

Hi, maybe anyone knows can I programming my bafang rear hub motor BFSWX02 500W 48V? What USB programmer I would need?

[@joshsontems-io7pe]

Can I put the bbshd 30 amp controller in my bbs02 so I can run it at 25 without having to worrying about the motor and controller overheating?

[@stevenc22]

I would say yes but you might as well just changed the motor of you spring bbshd.

[@joshsontems-io7pe]

@@stevenc22 I live in a state where for u to use an e-bike without a license the motor has to be a 750w motor…. I wanna be able to get 1300w but while it’s in a 750w case so tht if a cop every looks at my motor it still says it’s 750w motor so they won’t ask for my license

[@stevenc22]

@@joshsontems-io7pe You can't push a 750w motor to 1300w. That's too much.

[@davegott4783]

Would like to hire someone in south Florida to program my bafang

[@joaomarveloso1049]

Thank you for this very informative video. I have a Bafang 250w m400 motor. When I pedal I have a feeling that the engine only helps up to a certain point. Than I have to switch into a higher gear ( cassette gear ) and then it helps again. Do you know if there is a setting where I can prolong this help limit? I don't have a throttle, only pedal assist.

[@stevenc22]

Probably have a speed limit.

[@joaomarveloso1049]

@@stevenc22 Speed limit for every gear or generally? It is happening in every gear.

[@velimir.l.georgiev]

Thanks for the effort and for the video. Can I use a battery with 36v on 750w/1000w motor? You haven’t shown if you can change voltage below of 36v!

[@stevenc22]

No. Motors have a set voltage. Some motors are 36v motors and some are 48v motors. You cannot use a 36v battery with a 48v motor regardless of settings in the controller

[@velimir.l.georgiev]

@@stevenc22 Steven, I have read, that some of the Bafang 1000W controllers has got an option to be used with 36V battery and to change the voltage. But no way 36V motor with 48V battery!

[@stevenc22]

Be careful. A 1000w motor on a 36v battery means 35 amps. The wiring is not designed to carry 35amps. That is why 1000w motors only come in 48v because 48v uses less current.

[@velimir.l.georgiev]

@@stevenc22 The motor is 1000W 48V with controller of 30A! So, should be OK. My batteries are 36V/10Ah!

[@stevenc22]

@@velimir.l.georgiev no it won't be! At 36v you will exceed 30a of the controller. Also a 10ah battery is small. You are going to be hitting it really hard pushing 1000w.

[@skyliner4610]

can it be done with cheap chinese bikes? Duotts c29 750w

[@stevenc22]

This only works with a Bafang motor

[@DigitalSamTV]

just got my cable and programming now, so there are 9 levels in the software but i set my display to only show 5 levels (still goes to max power, just less time ti switch between) so what does it take from the sofware, like what is level 8 in the software, or its not counted ?

[@stevenc22]

I think level 1,3,5,7,9 in the software relate to your 5 levels

[@RockG.o.d]

You might know this. Can the amps be reduced safely to only use 250 watts max? I only want one bike for private land and also road legal.

[@stevenc22]

Yes of course. You can set a max amps limiting the bike to 250w

[@chevalierdelorimier776]

Hi , I have a Jorvik mt7 tricycle with a 250 w mid drive motor bafang M 500. I need to have more strength when I climb a steep slope. So I need a little more power when I m on the easy gear.should I slightly increase the ampere ? How many . Thanks for this amazing tutorial. Gabriel

[@stevenc22]

Assume you have a 36v battery, you currently only pull 7 amps then for 250w. You could probably do 10amps without much problem. Make sure the m500 is actually programmable. Some of the new motors cannot be programmed

[@chevalierdelorimier776]

Thanks Steven!

[@stuartthomoson]

Have you tried on bafang hub motors?

[@actionroom9226]

how do u have 9 modes i only have 5

[@stevenc22]

You can switch between 5 and 9 modes in the secret menu on the display

[@realohanaadventures5133]

I was going through the PDF regarding the speed limit. My LCD shows 28mph as the speed. How would I increase this if the Bafang config tool only allows the max of 40km/hr which is only 24mph. side note, i havent attached my controller to the laptop yet.

[@stevenc22]

The controller software speed setting is for the pas only. Using the throttle is not limited to 40km/h.

[@realohanaadventures5133]

@@stevenc22 Thank you for responding. Once receive the cable I will try. Hoping you will be able to help if needed. Appreciate you alot!

[@12linyih]

does this also work on m800 mid-drive?

[@KevinTPW]

Wow nice hack you are f****** genius xD xD

[@SR_YT_1234]

Quick question. Is there any programming cable for a Ananda front-wheel ebike engine?

[@RobertAdams-ly5ku]

don't know

[@tomhoefs3181]

How do I find the software I put the cable in but the laptop can't find the software you are showing. Do you have a link?

[@stevenc22]

edrivenet.com/bafang-programming/

[@MikeJordanUnCamplicated]

Great explanation of the software. When changing the throttle response, I see there is also a "Speed Limit" setting that is set to "By Displays Command" . You did not have to also change that? If you were in pedal assist 1 but needed speed to cross the road as the example you give, do your still get full speed?

[@stevenc22]

Yes if you set the throttle to full speed

[@roushsporthvacman7095]

Can anyone tell me if it is posable to reprogram a Himiway Cruiser controller ?

[@jorritjonkmans9196]

I've got a Bafang M200 middrive. With a 5 pins cable. What are thoughts on that?

[@stevenc22]

If it's the triangle connector, that cannot be reprogrammed.

[@MrMafioza1995]

i have 750W bbs02b with 48v 13.5ah battery. should it be possibleto boost it to 1000w or 900.. regarding battery ah ?Thanks .

[@stevenc22]

Yes. If your battery can deliver 20amp you can increase to 1000w

[@cippalippa5368]

Hi, i have bafang 250w 36v. How to setup in Low Battery protection and Current limit section? Thanks!

[@stevenc22]

For 36v your low battery cutoff is 28v and your current limit should be about 10amps.

[@cippalippa5368]

@@stevenc22 Thank you very much!!

[@hanniballisticbear]

Great information! Does this work on the 500watt front drive bafang? I just converted a 29 inch cruiser with front drive and it tops out at only 15mph I feel there is some limit put on it.

[@stevenc22]

To change top speed just go into your display's secret menu. Top speed can be changed with your display, no need to break out the laptop.

[@BROWNDIRTWARRIOR]

@@stevenc22 This is confusing. I thought this hack bypasses the limiter. My 1000w tops out at 37 km an hour no matter what menu setting I use.

[@TheFabiosolo]

What does it mean on the C965 UBE LCD display in pas?

[@stevenc22]

Sorry I don't understand the question? Are you asking in the laptop software or on the bike display?

[@Drivingsideway]

Hacking? This is Bafang user interface for advanced settings. It is possible to actually replace the firmware and actually hack a modified one with more power but highly likely to burn out the controller (which is in the motor case, not the display)

[@Trulshrn]

Nica Tanx. will it work on FTF 850C? Do you have a link to bye a cable.

[@stevenc22]

Link in description!. The 850C is the display. Programming has nothing to do with the display. It has to do with which motor you have. Which motor do you have?

[@draguvasile7991]

Hi were did you got the software from ?

[@stevenc22]

Link to software and tutorial in description

[@draguvasile7991]

@@stevenc22 and this work with rear hub as well??

[@stevenc22]

@@draguvasile7991 depends. Many bafang rear motors do not have bafang controllers. If the controller is not bafang, it won't work! I'm not talking about the screen, I'm talking about the little box that mounts in the frame of the bike.

[@draguvasile7991]

@@stevenc22 i see, mine one is somehow fitted with the battery so I can’t really tell , thanks for the information

[@munarriz2]

Would this work on a Kalkhoff with impulse 2.0?

[@stevenc22]

Not this software. This software is for Bafang motors. Impulse might have their own software

[@theartteacherdaniel5096]

Are you satisfied with the low settings for pedal assist 1-3? How many miles per hour or km per hours does pedal assist level 3 reach?

[@stevenc22]

Maybe 10mph

[@theartteacherdaniel5096]

@@stevenc22 thanks for your answer 👍

[@vHypnoticx]

does the battery have to be on whilst tuning?

[@waverley41]

yes

[@BROWNDIRTWARRIOR]

Hey man, spent 40 bucks on the Bafang programming cable but when I plug it into my computer I don't get anything other than the sound of the computer recognising the device. Is this a driver issue or should I be getting a pop up menu? I have a Juggernaut 1000w mid drive. Thanks in advance.

[@jasonpanagoulis7180]

I have a problem can read my bike but can’t write do you know why?

[@stevenc22]

Could be a bad cable. You sure you have a programmable mid drive? "Basics of programming BBS02 and BBSHD mid drives - Electricbike.com Ebike Forum" electricbike.com/forum/forum/builds/custom-ebike-motor-programming/bbshd-programming/43287-basics-of-programming-bbs02-and-bbshd-mid-drives

[@robertlockyer2287]

Hi mate, Would you know if there is a programme cable for the bafang green 5 pin triangular cable?

[@stevenc22]

Not that I know of. The triangle plug is an entirely different system and last time I checked no one had cracked it yet

[@robertlockyer2287]

@@stevenc22 Thanks for the reply mate. May just have to wait till my unit craps itself and then buy a display with the round plug.

[@stevenc22]

There is some basic programming that can be done with the triangle connector. I found this. US $31.90 45%OFF | BAFANG BESST Programming Cable Speed Limit Release Wheel Diameter Setting M400 M600 M510 All CAN Protocol Motor Dedicated Line a.aliexpress.com/_mKXKWYK

[@robertlockyer2287]

@@stevenc22 cheers Steven. I will look into it to see if it's worth it. Would have been nice to be able to set percentages for pedal assist and stuff like the non canbus type programmer cable. Oh well such is life as they say.

[@georgepene6097]

Great video , my question is if will works also for a front wheel, I've changed my motor and now I can't adjust the pedal assistance and it shows me a to higher speed than real.

[@stevenc22]

Only if you have a Bafang controller can you use this cable. It's likely you have a wiring issue or your controller isn't compatible with your motor.

[@georgepene6097]

@@stevenc22, thanks for answering so quickly. Can it be that even if its the same connector and the same brand that its not compatible with the controller?

[@stevenc22]

@@georgepene6097 if it's the same brand with the same wiring, I think it should work. Makes me think you have a wiring issue. Is your pedal sensor working? Does the display cycle between the different PAS settings? What does work and what doesn't work?

[@georgepene6097]

@@stevenc22, pedal sensor it's working and on the display its showing the rong speed, you can adjust the pedal assistance to minimum but the motor its running at full speed

[@stevenc22]

@@georgepene6097 does the motor always run at full speed? What about the throttle? Does that work right?