Hacking an Ebike with a phone: Reprogamming Bafang Mid Drives!

In a previous video i explained how to reprogram and overclock Bafang mid drive motors using a laptop. Now an Android app has been released which allows you to do all the same reprogramming on a cellphone.
Link to previous video where i went more in depth about how and why to reprogram an ebike.
Warning: the newest 2022+ Bafang mid drive uses a triangle connector not compatible with the programming cable.
• Hacking an ebike: how ...
Link to Speeed App on google play store
play.google.com/store/apps/de...
Link to OTG Cable
USB Type C amzn.to/3e4Yjhv
Micro USB amzn.to/3xKv1Nj
Link to Bafang programing cable
amzn.to/3hvPAaz
amzn.to/2UHRoUY
Link to Bafand Mid Drive Kit
amzn.to/302sLBq

[@marcinkopa]

Hi @Stevenc22 I am the author of this application, thank you for showing this. Cheers!

[@stevenc22]

Wow awesome app. Thanks for making it and not cramming it full of ad's.

[@dr.octagon9450]

Is there a apple version?

[@stevenc22]

Not that I'm aware

[@MrLottolee1]

Any update so I can connect to my Avaris and change settings?

[@harveyashworth6285]

My thanks to both of you, much appreciated. Question: I have a new build BBSHD/BBSO3 with a 52 volt battery and the DCP 18 (UART) display programmed with the ECO/SPORT settings. PASS’s levels are listed as 5 in both ECO & SPORT when connected to SPEEED 9 levels are visible. Do you know which levels are assign to ECO or SPORT? I have seen some that suggest this set up only uses odd levels 1, 3, 5, 7 and 9 but no mention of which mode uses them. Any assistance would be helpful.

[@MrPhunka21]

Bought the cable hoping to find someone with a pc to gelp me out.watched this video part way through went to the local electronics store downloaded the app at the counter as i was buying the otg cable rushed home, finished the video made 2 changes pressed the write option . And bamo worked like a charm .lowered my pas cutoff from 200ms to 100ms and changed my throttle response all other settings seemed fine .all from my android phone. Thank you for the video!

[@normandocherty4207]

Many thanks for this well put together video. My old Apollo bike was very erratic and jerky after my Bafang conversion, after watching your video video I bought the cable and set the parameters exactly as you have set yours, my bike is now running really well, couldn't believe it would be so easy . Also a big big thank you to SPEEED!

[@zickzion00]

Could you share the cable and programs that you buy... I would like to try it, but I dont know where to get that cable and programs.

[@hanssuckow7539]

I have used it and followed your instructions. Really easy to do. Now, I will check the settings on my bike!

[@ashpunting]

Thank you for that information Steve I've just ordered my leads so I can reprogram my bafang mid-drive 👍🏾respect Steve

[@johnbolt665]

I had the cable so I downloaded the app and it's as easy as described and the built in help file with all the settings is great too and all free!

[@adeharris4457]

Brilliant video, I'm eagerly awaiting my first mid drive kit & getting all the info needed before it arrives I've already received the programming cable, this is crucial info imo thanks 👍

[@June4600]

Thanks for posting this video 👍🏼 Super cool now I can use something as small as my cellphone to program my BBSHD other than my laptop.

[@daverumsey7629]

Thanks for this video. I hadn't been aware of the Android App.. very useful. The Bafang BBS conversion motors are not programmed well, and reprogramming them as you describe makes them much easier to live with. One comment.. the device on the handlebars that you refer to as the "Controller" is usually called the Display (hence "By Display's Command" as a setting in the program). The controller is mounted directly on the motor assembly, and its function is to supply power to the motor .

[@willdorten6867]

I agree. Idk if this would work with either of my ebikes but it would be nice. I like the way he wants his ebike's assists to be low until the higher levels. My Ancheer tried to throw me off the damn bike back when i first got on it, lol. I had no idea it was going to be automatically set on pedal assist.

[@sellanything]

Awesome Bafang reprograming tutorial! Thanks!!!

[@ashpunting]

I've downloaded this app and watched your video again and again while going through the app all I'm writing for is my cables anyway Steve have a good day brother 😀

[@mrjceltic]

Both your videos on programming the controller are really helpful. Just finished converting my MTB to an ebike with a 750W Bafang & have same controller 500c. Going to follow your settings as at moment in level 2 it straight up to 25 kilometres, 3 is 35 ks then seem very little change in speed till around level 6 by level 9 its scaring crap out of me lol. Cheers Mardy

[@richardcox3485]

Just ran across this video, you explained this process very well not confusing at all, good job Thanks.

[@stevenc22]

Thanks

[@MrTwistydave]

THANKS, looking forward to installing it. I can barely get to 30mph with a 52 tooth front sprocket. Above 26 is really seams to decrease power.

[@lucianosalt2396]

Thank you, just what I was looking for.

[@chipwright6193]

Thanks. I'm getting excited to buy a Bafang mid drive and try this out.

[@bradleyemmerson3728]

Have you got it yet?.... What Wattage did you get?...

[@chipwright6193]

@@bradleyemmerson3728 I bought the 48V 1000W motor with the 17Ah battery in the rack over the rear tire. I got it not long after I posted my comment. I put it on an old 10 speed MB my neighbor gave me years ago. I was really happy with it. I've been riding it most of the summer on our local bike trail with a friend. My buddy has an Aventon Pace 500 and I was outrunning him on it. Then his battery would go dead trying to keep up with me too! 😁 Make sure to plan out everything you might need to buy. I had to make a second order because I needed to get the shift sensor for the kit. I also upgraded my old gear changer so it wouldn't tear up my rear sprockets. Overall I'm really happy with it and I would do it again.

[@wulfsteppen6989]

@@chipwright6193 = HELL.oo from South FRANCE ! 😎 I just got and mount the same 1000W. 48V. BBS.HD on an OLD Alloy Frame MTB* ... PLEASE , did you Modify your Settings ? "WATT" is the Max. Amp. Limit on the 1000W. Controller ...Without BURNING it ? * i have to buy a BIG Front ChainWheel = Alloy 58T. instead of the Original 44T. of the Bike , and the 46T. Delivered with the BAFANG Kit ... THANKS to @Stevenc22 for this CLEAR Tuto. ...even for a "French Aboriginal" 🦍🥖😈🍷😎 !

[@chipwright6193]

@@wulfsteppen6989 I don't know what the max amp setting is on mine. I left all of the settings where they were. I entered the information like tire size so that my speedometer would be accurate, but that's about all. There are 9 speed settings on it and I left those alone. I like to use 3, 4, and 5. We have a bike trail that used to be an old railroad track that is 58km round trip. I can ride that on setting 5 and it will use about 60% of my battery.

[@jameskirk796]

Great app, and this guy does very well explaining the process. 😀

[@RobertAdams-ly5ku]

One of the best on KZbin

[@marcopargas8001]

Thanks for the info homeslice!

[@dougrich1970]

Nice 1 mate good job on the tutorial thanks 👍🏻

[@alberto4140]

Thank you very much friend for sharing the valuable info 🙂👍👍

[@Denvermorgan2000]

Thanks i didnt know this app existed now i can program my bafang easy.

[@keithmonk4503]

Good video. As you say this software is extremely solid and a dream to use, used it for 6 months. One suggestion, save the original settings in a file on your android device. (Software let's you do this easily) so you can return to these settings if you find your changes don't suit you. The changes to the throttle settings are a good use of this software.

[@cherylcarey4975]

I had wondered about being able to save the default settings before messing around with them. So, the speeed app has this capability? Or is it the phone you save through. I'm not clear on this. TIA for any help you can give!

[@whatsit2ya247]

I assume you figured this out by now? I haven't played with it yet, I'm still a little nervous lol , is there a way to save original settings before I mess with it from the app?, on my phone? Thanks!

[@harveyashworth6285]

Take pictures of the original settings first, so you can reference them later if you want to.

[@RobertAdams-ly5ku]

@@harveyashworth6285 That’s the way I will do it, good tip

[@ashpunting]

Thank you man that app works perfect I've only changed my throttle to work at full power all the time 👍🏾😊 it was worth getting just for that I do the same yo my other bike as well

[@stevenc22]

Awesome

[@ashpunting]

@@stevenc22 it was easy after you explained everything so clearly 👊

[@KeithAVass]

I am still looking for a reason why I have lost my PAS but it is looking more and more as if this happened ever since I modified my settings as per your video. I would love to get a definitive explanation from Bafang but as usual, they are providing NO SUPPORT OR HELP???

[@TheKingsRansom]

Great video explaining the app and motor setting mod. Will the app work with Bafang Ultra motor?

[@stevenc22]

The new Bafang ultra uses a rectangle connector instead of a round connector and uses a different communication protocol that is not compatible with this app and programming cable

[@nicelight3475]

Ooh, this is very good. Thanks.

[@auroraprospecting]

Thankyou so much for this info!

[@stevenc22]

Glad it was helpful!

[@BalduinTube]

Perfect this eases life a lot! Works with an M400 Motor as well, but does not allow to change the torque settings. Is it planned to integrate torque settings as well?

[@stevenc22]

Sorry Mark, don't know what the developer plans to support.

[@kikijcl49]

Grea.......t. You are the best. It's so easy to use. Thank you very very much.

[@Leevan3]

thanks for the info, liked the video 👍 i have a bafang ultra that does not throttle from a full stop. i love the bike but this feature is important to me because i do a lot of commuting in NYC traffic. is there a setting in the app that can make the throttle work from zero? thanks again

[@stevenc22]

Absolutely. However the new Bafang ultra with the triangle connector is not programmable! If you have an old Bafang ultra it should be easily programmable

[@mikejoseph425]

@@stevenc22 How do you actually do it. I always find myself in the top gear so am looking for instant reaction when I peddle

[@stevenc22]

@@mikejoseph425 Mike what are you looking for? There is a setting for how many pedals the motor waits before kicking in? There is a setting for the throttle reaction?

[@stevieatkinson3898]

Superb 👍👍👍

[@daytriker]

Steven, I have a 48 volt BBS02B & can connect through the Green LCD Display cable & get the OTG program cable to light up but when I try to connect the phone to my motor I get a "Device not found" message. Is it possible that Bafang has made a change to prevent connecting to their firmware or do I need an up to date Android phone? Thank you.

[@philrichmond7567]

Thanks for sharing 👍🏼

[@yuding9406]

Great video ,btw where can i get the programming cable pls ? Or can i make myself ?thank you

[@stevenc22]

You cannot make it. Just buy it www.amazon.com/dp/B08NJH59BJ/ref=cm_sw_r_as_gl_apa_gl_i_TG6ZNB1XY4PWYRK5R1B4?linkCode=ml2&tag=stevenc22-20

[@xJayteee]

Well this is something new. Not only can you program with your phone , you can also use it as a display! Water got into my display and I guess i no longer have to get a replacement display .

[@xJayteee]

@A8W Phones nowadays are more water resistant then you think. I've had 2 displays damaged due to water ingest whereas my phone which is ALWAYS on my handlebar is still working fine.

[@818Ready]

Hey ya Steve appreciate the the details from both of your DIY vids but the Android is a bonus play. A head scratcher as 2 Y FLX would sell you the throttle as an extra ad on and then default it to your PAS levels only ???

[@stevenc22]

Probably for safety. Some people want to go slow and so some people will like having low throttle with a low pas. Not everyone will like having a throttle set to max.

[@rdkuless]

isn't the "throttle" simply a rheostat... the harder you press/turn, the slower/faster it takes off? So in Throttle setting 8 @ 80%, wouldn't it take off slow if you only press lightly or fast if you jump to full throttle..? My bike throttle is scary.. last time i tried getting rolling by throttle alone, i pulled a wheelie..nearly dumped the bike.. Suggestions on settings to have full range but also e able to start off slow and gradual..?

[@demonxelloss]

wow just awesome i'll set 52v on my Bafang BBSHD via this app because my 850c display can't

[@smallhatshatethetruth7933]

I'm still waiting for my damn cable, just installed bafang tonight and already I can tell the stock PAS is super lame without even riding it!

[@pachoota]

Is that the 750 watt settings your in after you connect motor,status,model, manufacturer, hardware, firmware info, if so could you also give year of purchase so I could order that version controller

[@gavinneuvenheim5016]

Nice video! Do you happen to know if this works with a Tenways E-bike as well? It does have the same SW102 display, only the motor is not Bafang but Mivice M070 250W.

[@stevenc22]

I don't think so. That motor looks quite different.

[@bbbeeelll666]

Many thanks! A question. where is the option to alter the walking assist mode when you press the minus? Also, the link for the cables you put in, is that also usable for the bafang m400? When I google for a program cable for the m400, it shows a different, much more expensive one. Thank you!

[@stevenc22]

There is a round connector and a triangle connector. If you have the round connector that works with my cable. If you have the triangle connector, that is the newer style which is much more expensive to program.

[@MrLottolee1]

I'm getting an Avaris bike any ideas how to get rid of the restrictor?

[@jamesbomd3503]

The Golden motor 4 wheel had an app similar, that we used on our smart Phone 9 years ago

[@rolandthielecke7780]

Graet, thanks for the Video. I searched very long for an App to configure my Bafang BBS02 /50 watt motor. Until now I used my PC for the configuration, but on travel I don't want to carry my Laptop. Greetings from Verona, Roland

[@bockerwright4132]

Great video this is but I'm a little confused. I'm planning on fitting a mid drive this weekend, got everything needed. I have tested the controller (500c) and it's working with the battery, I just connected together what could on the worktop to get an idea of how it all fits. I noticed the controller only has 5 assist levels but this app has 9. How does this work? Should I just average it all out over 5 levels or go ahead and program all 9? It sounds like your riding style is similar to mine so I would like to try to replicate it.

[@stevenc22]

You can change the 5 to 9 in the secret menu. But even if you keep the 5, in the software 1,3,5,7,9 correspond to the 5 levels

[@stevendietrich8183]

hey idk if you could shed some light on whats going on with my situation at all, but i bought a otg cable and the other one to connect to my magnum scout that runs a bufang motor. i try plugging my phone into the bike and it tells me that it cant connect to the motor and idk whats wrong. ive noticed that the cable i bought to connect to the bike isnt see through, like alot of other vids ive seen. idk if this has something to do it with it. hope you can help!

[@jorgepelaez2]

Hi and thanks for your video. One question, is it possible to connect the bafang bbs02 with the mobile through the USB port of the display?. I have the p850c display and this have an USB port. Thanks a lot.

[@stevenc22]

That is a USB charging port only.

[@rdkuless]

I got this and it works.. be careful when making adjustments.. I wanted my throttle to be less aggressive.. went to "throttle" > READ... then adjusted then lowered the "start voltage" lower to .5.... This gave me a error code, 04H... (this means throttle high voltage) which didn't make sense.. The motor wouldn't turn with throttle and the PAS stopped.. OH NO....! I went back and read the help icon... it said it must be at the least 1.10 start voltage to operate or the motor shuts down as not to damage the motor because the current is too low. My recommendation.. only reset one of the parameter at a time.. otherwise, it is almost impossible to figure out the change you made that caused the bike to shut down.. I read somewhere, if you get a error code 04H... disconnect the throttle cable, and if the error code goes away.. replace the throttle.... NOT THE CASE.. you just need to reset the Start Voltage setting to min 1.10... And do not set over 4.40 top throttle voltage or you can burn out the motor... This is a big LEARNING EXPERIENCE... But the app an the adapter cable work great..! Thanks

[@whatsit2ya247]

Thanks for the heads up! I haven't messed with mine yet and comments like this aren't giving me confidence, lol!

[@faroutdicht]

Very good video 👍. I've got also the programming cable but it doesn't show the red light after i plug in and switch the battery on. I've got a BBS01 Motor.

[@stevenc22]

That is weird. Makes me wonder if the cable is bad.

[@faroutdicht]

@@stevenc22 I guess also. I will fetch another one...

[@smarc1325]

an Eggrider... not that xpensiff and waaay cooler.. but very nice and helpfull video.. cheers mate,,,

[@ivanpetrov2280]

Hi mate, i was use your video for programming my bb02b. But have another question, i looking at one 250w hub kit , and the controller have the same cable types. Do you think i will be able to connect with this controller???

[@stevenc22]

I think if it has the exact same round green plug it will probably work.

[@user-hm3tc5no8r]

I have an e-bike Kugo Kukirin V1 Pro- is it also possible to connect and hack with the phone?

[@dalegreenaway]

Thanks boet!😊

[@silbernersurfer8264]

The Dpc181 seems to have bluetooth. Will the app work with the Dpc181 via bluetooth?

[@bengardner9296]

I have the eggrider display for my BBSHD, it enables some programming via USB, any advantage to doing it the way you've done it here via the cable?

[@stevenc22]

I don't know what options are available on the eggrider. If it had some good options I'm sure it will be fine

[@FATBIKERIDER]

cool il have to give this a go

[@saib8235]

Hi i replaced my bafang m400 drive with a 2nd hand drive.everything ok but it keeps reading the total mileage of the old engine.do you know why?thx

[@valbru1196]

If I have the 250W version limited to 25km/h, can I unbridle it to go beyond that?

[@nybluesking]

Hello and thank you for the video!! Does this cable and program work for Bafang rear hub drive controllers?

[@stevenc22]

Maybe. Most bikes with rear bafang motors actually have aftermarket controllers that it won't work with. If your controller box is actually bafang it probably will work.

[@nybluesking]

@@stevenc22 Thank You very much!!!

[@VITTORIOBESAZZA]

..ok!..bel video...istruttivo..bravo.

[@Jonas-km4qx]

Thanks mate!

[@michaelnguyen7483]

Hi Steven... I Cant go in my iGo 3.1 Factory setting.. to unlock..and I can't not see the speed magnet on the wheels.. I need your help to unlock it.. please I'm new to ebike.. please help

[@harveyashworth6285]

Terrific info, thank you, thank you. I think my brain is too full(info overload), now I’m wondering which battery to get for the 750W kit.? I live in a hilly area of West Virginia.

[@stevenc22]

So a 750w kit is probably a 48v system. So you need a 48v battery probably 12kw+ in size

[@whatsit2ya247]

Then why are all the builders putting 52v on their 48v bafang mid drives? And sellers selling 52v batteries with their kits? P.S. I just installed a 52v battery on my 750w. Now I'm going to program it to cap the amps to around 20 and theoretically get way more distance between charging than a 48v with the same Ah.

[@stevenc22]

@@whatsit2ya247 A 14s battery has a max voltage of 58v and a median voltage of 50.4 or 51.8v depending on whether you use the 3.6v or 3.7v standard. Basically a "52v" battery is a 48v standard just because the batteries have such a wide range of voltage full or empty. Empty it will get down to 40v which is too low to power a 48v battery.

[@whatsit2ya247]

@@stevenc22 I'm not quite getting it, so all the people that are using 52v batteries with their bafang motors aren't actually working?

[@pianoschmiddy]

Where can I get the PC software to configure the motor? Also, where can you get the new programming cable for motors after 2022? Thanks for your video

[@stevenc22]

My other video I show how to program with a laptop. The newer motors are not programmable as far as I know.

[@phd9590]

Wonderful but what in case of canbus connector and not uart (round) you are presenting. ?

[@stevenc22]

I don't think the new style connector can be programmed

[@VITTORIOBESAZZA]

..eccellente..conciso e chiaro...ti offro una birra..virtuale purtroppo..

[@jimt4906]

Hi Steven; looked on Play store says App unavailable . Ive got an S22 so no concerns there with it being too old. Also where can I find info on the Bafang M620 motor programming and cables?

[@stevenc22]

You can install it by side loading the app in Android or use the windows version on a laptop

[@kencook4956]

In the Google Play Store, I get a message that this app isn't available for your device because it was made for an older version of Android. Any suggestions?

[@beerman1957]

There is also a web version that works on most computers. I could not make the web version work on my Mac M1 Max.

[@peterbelliveau258]

What speed do you get at 5% and 10% and does it feel like a regular bike pedalling with some effort?

[@stevenc22]

My level 1 and 2 definitely need some manual effort. They only provide 25w and 50w of power which is nothing really.

[@calvintanner7897]

My motor isn't a mid drive so I'm not sure if this will work on bafang displays.

[@florentindragan]

hi! can you unlock Bafang with DPC245 display? Thank you!

[@MultiBloxx]

I have a bafang Rear hub motor is there anything like this for my bike.?????

[@daytriker]

On previous installs with the BBS01 my biggest complaint with those motors was the delay for the motor to stop after you stopped pedaling. Does this also occur on the newer BBS02's & also when using a throttle? This was most annoying for shifting or quick stops & I am hoping changing the stop delay will solve this. Thank you.

[@stevenc22]

I have not noticed any delay in the motor after I stop pedaling

[@daytriker]

@@stevenc22 Thanks

[@ridgeline_athlete]

Thank you so much for this. Can this be done with an iphone also? I'm not finding the SPEEED app...Thank you!

[@stevenc22]

I think it's android only. But there is a windows version of you have a windows laptop.

[@ridgeline_athlete]

@@stevenc22 Great thank you! I wasn't able to get my computer to recognize the windows version, so I took it to a bike shop and the tech there got it up and running. Thanks again for the videos!

[@Spinoza11]

Can i increase the speed stacked at 25km/h on mate x 250?

[@auroraprospecting]

Do you have a tutorial on how to update newest firmware on DPC-18 display using my android phone or a windows computer?

[@stevenc22]

Sorry I don't.

[@tridrles]

Will this app work on a Bafang Hub Motor???? I have a RadRover 5.

[@BareERaws]

This doesn't void warranty or anything does it? Because, this seems fantastic to be able to adjust...

[@stevenc22]

As long as you don't over amp it you should be fine. Bafang provides the tool them selves. This is officially supported.

[@ralphb3802]

Hi, great tutorial, but still have a question.....my throttle is to jumpy, it will make me wheely the bike if I'm not careful when starting off, what setting should I use to make the throttle more like an accelerator in a car. Thanks Biktrix Stunner X Bafang 750 mid drive

[@stevenc22]

Yes there is a setting. Let me check for you.

[@stevenc22]

Okay check your settings for start current and slow start mode. Use 10% for current and 4 for slow start mode.

[@florentindragan]

Hi! Does this work for Bafang M200? Thank you!

[@justiceonly9105]

Hi, Do you think this application works on the rear hub motor of an ebike also? Thank you

[@stevenc22]

It might work if your controller is Bafang.

[@richardcarlson4327]

Does this programing apply to the latest Bafang G510 Ultra mid motor with an arrow shaped 5 pin connector (not round connector)?

[@natblud7806]

Not yet

[@sandroolivieri5310]

​@@natblud7806allora non funziona con m500 attacco CAN?

[@ivanpetrov2280]

Thank you for your video. I have few questions to you and anybody else. I have bafang 750 bbs02b and battery 48v 17.5ah. What actually do? Increasing of the watts motor, in your case you rise the A up to 20 ( this is like 830w approximately) what actually will hapen? Make more power for acceleration? Or Increasing the top speed? Or both?? Thank you.

[@stevenc22]

Both. Increased amps improves acceleration and top speed

[@ivanpetrov2280]

@@stevenc22 that sound good 😀 i already order the programing cable .

[@joelfiat147]

It s 960W

[@bergmanst]

I picked up off of Amazon the cable I thought I could use for the programing my mid drive BF and found out the newer Bafang motors changed the plug in on the cord from the LCD to the motor had changed; so you can not reprogram the new Bafang motors. Will there be a newer cable in the future for us owners of the new motors to be able to reprogram our motors?

[@stevenc22]

The new motor actually uses a different programming language, so I'm not sure.

[@Ezio470]

which model you using?

[@bergmanst]

@@Ezio470 G510 1000 watt

[@johnstather5815]

speeed bafang or speeed app choice of apps

[@rec105mediagroup7]

First at all many thx for your video. My question is: on my fat bike is the BF HR500 rear motor mounted, the display is 850c full Color, I don’t know which controller is mounted, I hope ever from BF, you think I can use this app to programming? Thx in advance.

[@stevenc22]

Since we don't know which controller you have, we cannot be sure. However for $10 its probably worth buying the cable and trying it out!

[@rec105mediagroup7]

Today i found out the Brand of the Controller, LSDZS LSW1440, you ThinK CAN work the Same? When you change the Parameters this make change on the Motor or affect the Controller? Thx again.

[@stevenc22]

@@rec105mediagroup7 that is not a Bafang controller. It is probably not programmable!

[@thepostalcadet253]

Hi. Do you know if this will work with a Bafang 250w rear hub?

[@stevenc22]

Depends. Just because your wheel is bafang doesn't mean the controller is bafang. If your controller is not bafang, it won't work.

[@grahamk2397]

Great video. After your changes do you use the “disconnect button” on the app or do you just disconnect the cable from the bike?

[@stevenc22]

I think as long as you have saved your changes you can just disconnect the cable

[@grahamk2397]

@@stevenc22 thanks

[@alistairbarclay3116]

If you have a front hub Bafang motor will this software work when it is supplied with the very basic c 951 controller? I want to make the cadence or torque sensor respond to pedal movement faster. At the moment it is nearly two full revolutions of a pedal for the PAS to cut in?

[@stevenc22]

The c951 is just the display. The controller is the box of electronics in the frame. The problem is many bikes use a bafang motor but not a bafang controller and you need a bafang controller to program anything.

[@alistairbarclay3116]

@@stevenc22 ah thanks so I must find and pull the controller and see what make it is and the specs I suppose and start from there, thanks for the help.

[@PauloSantos-rm1mt]

Where do you change speed limit? From 25 km/h to 32 or whatsoever? Many thanks

[@vitcand1]

speed limit in the lcd can put the limit you wont

[@joosheim]

Is it possible to reprogram an Crescent Elton bike with this app? New to this, trying to get a grip of how it works! Thx!

[@stevenc22]

I don't know that bike brand. Does it use a bafang motor? And if it does, does the display use a round green connector? If yes to both questions, then it is probably reprogrammable.

[@willdorten6867]

So if my ebike is like this Bafang, which is possible imo as Bafang seems to be the primary caregiver to other sister companies or copy cats... the speed limiter on my ebike just might be as i am suspecting, in the controller itself, under those settings in the pedal assist tab, because maybe level 5 (top assist) on my ebike is programmed to fall short of 100%. Can anyone tell me if maybe I understand this? Because I'm not going to try and reset my LCD display like some others I think may have from my research, and come up with an error, basically bricking my ebike, lol.

[@ljaproductions07]

I've been playing with my settings and somehow my pedal assist has totally disappeared, does anyone have any tips on how to restore it? Or restore the original settings on a Bafang BBS01 36v 250w mid hub motor?

[@MikeSmith-pe5re]

Same thing happened today me. Were you able to get PAS back?

[@A.G_369]

can i use on model Bafang 750w BBS02B ? and can I change on this model not 24 amperes, but for example 28 or 30?

[@stevenc22]

Yes you can use it on bbs02b as long as it has the round connector not the triangle connector. 48v x 30a is 1400w. That is too much.

[@ashpunting]

Hello Steve I hope you are well a quick question I've just ordered the eggridder v2 display could I program both my mid-drive bikes with the eggridder but only use the eggridder on one of my bikes and use the old display on the other and will my settings keep on the other bike once I've removed the eggridder 😊🙏

[@stevenc22]

I have no played with eggrider my self, but I want to say yes. Once the settings are saved to the controller, the settings should stay regardless of what screen is plugged in.

[@ashpunting]

@@stevenc22 thsts whst I thought and thank you for you help Steve have a good day and stay safe, my friend 😊

[@Shawrtz]

@@ashpunting are you happy with the Eggrider? I’m wanting to order for my Radrunner. Where did you order from?

[@HenryZold]

Say, i have a fat bike rear 26.4 hub motor that isn't a bafang model that's equipped with the SW900 LCD; my question is this: can i program my hub motor with that programmer you have???

[@stevenc22]

No. You need a bufang motor and a bufang controller

[@erik_dk842]

How about the Bafang OEM middrives,the ones that require a special bike frame, not the BBS which van be retrofitted. Can they be tuned as well?

[@stevenc22]

If it uses the round connector to the screen, it can probably be reprogrammed. If it uses the newer triangle connector for the screen, it cannot be reprogrammed.

[@erik_dk842]

@@stevenc22 I don't know yet. It's my friend's new ebike with "Motinova" motor, which is probably just a rebranded Chinese motor.

[@andymacka5553]

Does it work with phaserunner