Love y’all channel definitely would love to get a bandit on my job boat when they get completed
@LoneStarHovercraft4 жыл бұрын
Thanks! We’ll keep you updated on the progress
@jim-jf5rn2 жыл бұрын
Love to set up but if you put a larger pulley on the motor and a smaller one on the fan you'll get more power out of the fan.
@user-qx3bg9pn6j10 күн бұрын
Do you recommend a 6-bladed fan for small (e.g., 5'x8') hovercraft setups?
@LoneStarHovercraft9 күн бұрын
Depends on a couple things, if it’s for both lift and thrust, I’d use a 6 or 7 blade fan. If it’s only for thrust, I’d use a propeller like this if it’s going to be over ~40” and you intend to run it open (no duct) or go with the fan instead if it’s going to be smaller than 40” and you intend to build a duct for it.
@elhau27 күн бұрын
What size v-belt are you using? Isn't that too narrow? Probably you've tested that alright
@normanhebert23882 ай бұрын
64" 3 blade prop
@bibrakc Жыл бұрын
Do you change any internal components of the engine? Like the connecting rod, push rods, piston, value etc?
@LoneStarHovercraft4 ай бұрын
Not when we run them on mini airboats. we normally just leave them stock and tune the carb.
@thomaspeters91743 жыл бұрын
Im fixing to build one gonna try it out cuz i live by the river....
@user-vi2nh6ee2k3 ай бұрын
Que reducción usas en las ruedas ?
@justfixitnow774 жыл бұрын
Where did you get the hub from. I picked up a prop but it is missing the hub
@LoneStarHovercraft4 жыл бұрын
You can get replacement hubs directly from Competition Aircraft
@joseguillermomorenozarate86222 жыл бұрын
Por favor donde consigo el motor con la hélice y cuánto cuesta
@chris27902 жыл бұрын
Would not use this engine on an aircraft. It does not use a bearing for the crankshaft. It's just a bushing.
@michiganmagneto3 жыл бұрын
Whether you're using direct drive or reduction drive, do you still run those engines with the governor?
@LoneStarHovercraft3 жыл бұрын
Yes, we leave the governor on because we find it simpler to attach the linkage and we don’t need to rev past 4000 rpm. On some of these small engines the governor can make it act squirrelly (surging and hunting) so in those cases people usually adjust them or bypass them
@williamnaylor24882 жыл бұрын
the prop is the governor!!!!
@michiganmagneto2 жыл бұрын
@@williamnaylor2488 not really, because after a specific rpm the aerodynamic propellers don't do anything but waste fuel. That's why you kind of want to match the max engine RPM to the max propeller RPM, factoring in a reduction drive if used.
@williamnaylor24882 жыл бұрын
@@michiganmagneto then why are there no governors on aircraft motors? unless you have a motor with unlimited power the pitch of the prop sets the max motor rpm! I have been building and flying aircraft for 40 years that is how we match a prop to an engine.
@topher1744 ай бұрын
Curious as what the red hose is? Oil pressure gauge?
@LoneStarHovercraft3 ай бұрын
That’s just a drain hose to make oil changes easier
@michaelpowers7768 Жыл бұрын
Could this work for an ultralight trike?
@aratoctimpoloc91424 жыл бұрын
How can i buy engine like this,.and how much the prize...
@valtercuiabanocuiabano43252 жыл бұрын
Onde acho essa helice
@tahminaakther54143 жыл бұрын
Hi sir. I'm Bangladeshi. How can i buy this engine and propeller
@LoneStarHovercraft3 жыл бұрын
We can ship the propellers world wide but I’m not certain about the engine, they are too heavy to ship internationally
@chrisisboss96203 жыл бұрын
How well would this work on a 14/36 jon boat
@LoneStarHovercraft3 жыл бұрын
It would do pretty well. We normally run them with a 44” prop on a boat that size. It’ll push one person and some gear around 20 mph. It’s possible to push two people with it but with limited gear and depending on the size of the people
@mizanahmed95013 жыл бұрын
Does anyone know the price of this Injil in Bangladeshi rupees
@joelkoonce85593 жыл бұрын
How do I order a predator engine and prop ?
@ericmenuier91372 жыл бұрын
We're can I buy the kit to do this?
@LoneStarHovercraft2 жыл бұрын
We have the belt reduction drives and propellers on www.banditairdrives.com
@mizanahmed95013 жыл бұрын
I need such an engine. Please tell me how much it costs
@LoneStarHovercraft3 жыл бұрын
The engine itself is currently $829 at Harbor Freight
@mizanahmed95013 жыл бұрын
@@LoneStarHovercraft I am speaking from Bangladesh... So ... Who can I take the engine.... And Bangladesh price....