Nissan Xterrra (No Plenum Removal) Coil Pack and Spark Plug Replacement

This video will show you how to remove the right bank coil packs and spark plugs from a 2004 4.0L V6 Nissan Xterra WITHOUT removing the intake plenum. You'll need a 3/8" socket extension with a wobble tip, a telescoping magnetic pickup tool and a stubby 10 mm ratcheted box wrench. Aside from that, a 3/8" metric socket wrench set is all you'll need.
If you'd like to make a donation to the channel, please follow the link below: paypal.me/Hard...
Parts & Specialty Tools:
3/8" Extension with Wobble End
amzn.to/2GChQWz
Telescoping Magnetic Pickup Tool
amzn.to/2DytjEC
10 mm Stubby Ratcheted Box Wrench
amzn.to/2Xym5Yw
Hitachi Ignition Coil
amzn.to/2Dw2DUL
Denso Iridium Long Life Spark Plug
amzn.to/2IECkQK
Dielectric Tuneup Grease
amzn.to/2DsF4fO
Anti-Seize Lubricant
amzn.to/2DqAoXt
As an Amazon associate, I earn from qualifying purchases. Thank you for your support!
Please Subscribe: goo.gl/x6fyS

[@williamgrandy698]

Thank you, thank you! I tackled this today and was successful in about 2.5 hrs. And I didn’t need to remove the hose for the rear passenger side plug. Your video made it easy on me.

[@hardlymovingpro]

Glad it helped!

[@ChezzusXrift9]

Man the struggle is real! I really do appreciate the way you showed how to get these spark plugs out of these tight locations using those tools. Anyone who's ever actually laid eyes on some of these V8 engines will know how tight those spaces are but I think you did a very good job and you played it really smart. Thank you for this video and keep it up!

[@hardlymovingpro]

Thanks!

[@Alfred5]

I tried it and everything went smoothly until one of the 10mm bolts that attach the coils broke off. I was livid. After that experience I spray kroil and WD40 on the bolt several times to prevent it from getting stuck.

[@wellnessotr]

I had to watch this video about 30 times, and go out and try it… on day 2 I was able to understand the angles of using the tools. Whew! I’ve never done anything like this before…but I am super proud of myself for taking it on! 🙌🏽 It took me about 4 hours to complete this project. I’m totally oK with that because it’s a learning experience for me. That coil on the front was OMG so challenging, but I actually got it out through the front of the motor. Whew! After that one, it’s just a matter of following directions, etc. thank you for your wonderful video. It helped me tremendously. Most of my boots were stuck on my old plugs, and I pulled too hard on the first one and ripped it. Good thing I already had a new one. But, what I found, for the others, was that using a plastic body panel removal tool to help pry up the boots, was perfect.

[@hardlymovingpro]

Glad it helped!

[@butchgreene]

It’s easier to take the plenum off . I suck at wrenching and have had mine off twice and would rather do it and just back the plugs out than to do this method

[@towermoss]

Every time you grunted or sighed I was like, "I feel ya brother!" Thanks for making this video, I really didn't want to take off the manifold and have been putting off this job for a while. You da man!

[@hardlymovingpro]

Glad you enjoyed it!

[@nomebear]

This worked! The long grabber tool and flat 10mm ratchet are a must. It took about two hours to buy the tool at HF, the coil pack, and to get the job done. Thank you again for the professional and detailed video.

[@hardlymovingpro]

Nice work and thanks for sharing!

[@darcyk5548]

I just finished and am so thankful you showed how to do this without tearing the whole engine bay apart! Thank you so much! ❤

[@hardlymovingpro]

You bet!

[@hhdegimr]

3yrs later and this is still a great vid, just replaced then on an 06 xterra, pain in the ass but not nearly as much as the other way. Thank You!

[@hardlymovingpro]

Glad you liked it!

[@thomasblanco4995]

Excellent, I used your video and was able to accomplish this with relatively minimal pain. Stubby 10mm ratcheting box end was key removing #1. Good stuff!

[@hardlymovingpro]

Good for you and thanks for sharing!

[@onehelewaguy]

THANK YOU! #1 coil went bad. I had no idea how I’d get to it. Enter your video- simple, clear, and SUPER helpful. Swapped the coils w/ #3 to confirm diagnosis (def bad!!), replaced all the spark plugs, and she runs like a champ. Just cost me for parts, a set of pliers I didn’t already own, and my time (you saved me my sanity). Thanks again! ‘06 Frontier.

[@hardlymovingpro]

You bet and thanks for sharing!

[@-danfangmeyer-5497]

Ya buddy, my #1 just went out too. Really didn’t want to take the whole thing apart, super glad I found the video. Wish me luck

[@hardlymovingpro]

Good luck and have fun!

[@larrydykes7643]

WOW this is an absolute MASTERPIECE of "tight spot" mechanic work!

[@hardlymovingpro]

Glad you like it!

[@LoneTenor]

Just changed my frontier plugs! Thank you so much for this tutorial, it saved me over $800 and only took me 1.5 hours to do! 😁😁😁🥳🥳🥳

[@hardlymovingpro]

Good for you and thank s for sharing!

[@Alfred5]

I did this a few years back. It was very tricky to figure it out. I wish your video was available back then, it would have helped a lot. Thank you for refreshing my memory and providing me with a better way to do it next time.

[@hardlymovingpro]

You bet!

[@ssnider7967]

Thanks so much for this video tip!!!! my #1 coil went bad on my 2006 Frontier, and I was dreading to take off the intake plenum. Saved me so much time and effort. only tough part was the bolt holding the coil pack on, everything else went smooth.

[@hardlymovingpro]

Glad the video helped and thanks for sharing!

[@dswitz9997]

Just changed my spark plugs today. If you hadn’t made this video, I woulda pulled my entire intake off. Thank you for saving me all the time and stress of changing my spark plugs!

[@hardlymovingpro]

Thanks for letting us know of your success!

[@chrisv5139]

I do it like this all the time, haven't done plugs in a while and you helped to refresh my memory on this and I am thankful. Now I have the confidence to go and get the parts and the job done, great camera work btw, helped a lot

[@hardlymovingpro]

Glad you found it useful!

[@jayg2779]

Wow. When I first looked under the hood of my 4.0L Pathfinder I thought Ford engineers must have moved to Nissan. This video was spot on. As my usual practice, I start with the most difficult one first working through the easier ones. For this set up that meant starting at the front right, v working down that side and starting at the back spark plugs on the other side working forward. Thank you for the video, it really helped me keep perspective on this swap.

[@hardlymovingpro]

Glad it helped!

[@kimlee9917]

You are a genius sir! Thank you for sharing this video. I had a P0301 code and replaced coil #1 without having to take off the intake plenum! I just replaced all the spark plugs while i was at it! Thank you for sharing this video!

[@hardlymovingpro]

Good deal ... glad it worked out for you!

[@thinkingimpaired5663]

I'm amazed i'm getting the same code. Did you have any issues with the new coil? Was your code being thrown after the motor warmed up with the old coil?

[@dodgersnation8574]

Thinking Impaired where do you get the code and how do you know when it’s misfiring?

[@thinkingimpaired5663]

@@dodgersnation8574 I bought a obd2 scanner from Walmart and pulled the code from the scanner. There's a huge number of scanners out there but the most basic one worked for me. They range I believe 20 dollars and up. Mine was I think 40 to 45 dollars. By the way I moved my supposedly bad coil to an easily accessible cylinder and switched out the coils. Then reran tests to see if it actually was the coil or if it was an electrical connection. My coil worked well for a while then through a code. That's when I knew to replace my coil. I replaced my bad coil with a Denso that was made in Japan and not it's hinshin subsidiary in China. It was the cheapest coil and I'm pretty sure it will work just as well as the coils costing 2 to 3 times the money. I dealt with Napa Auto Supply my best source of OEM parts. All my factory original coils are hinshin.

[@dodgersnation8574]

Thinking Impaired is there a book of reference to let you know that the code you receive is in fact telling you it’s a bad coil and for any other code? Thank you!

[@gabrieluribe1852]

Your a great camera man and a good mechanic, now I got to try your ingenuity to do this on my 2013 Nissan Xterra, and I'm a plumber not a Macanic.

[@hardlymovingpro]

Good luck then! It can be done!

[@DavidHernandez-ue4fz]

You did it?

[@Dogg416]

I have to agree with everyone leaving comments. Great job !! The pathfinders a little different, there’s a metal bracket in front of #1 plug but it’s still doable with your method. I figured out if you get the neighbours kid to help they can get in those tight spots and make the job a lot easier lol. Thanks again

[@hardlymovingpro]

Thanks for your comment and support! Really appreciate it. Checkout my latest video on doing a Hyundai Sonata engine swap!

[@jamescruz664]

Flippin awesome dude!!!! Thank you very much for making this video. I had code P0301 and replaced coil #1 without having to take off the intake plenum! Removing the adjacent coil first made all the difference. I grunted and moaned a few times myself, but starting her up and no more check engine light made it all worth it.

[@hardlymovingpro]

Glad it worked out for you!

[@Ju-uy1cs]

I ran across two other videos, basically saying you have to take off the air take manifold. Im glad i kept searching videos

[@hardlymovingpro]

Isn't it wonderful that the plenum doesn't have to be removed?

[@Ju-uy1cs]

Hardly Moving Productions It definitely is a good thing, thank you for this video

[@Ju-uy1cs]

Can you use a 1/2” extension and 1/2” metric socket wrench? Or does it have to be 3/8”?

[@bodiaz1104]

Ok, it's not an easy job, but doing it myself the way your video shows I was able to do the job and saved about $300 or more that the Mechanic was going to charge. So Thank You very much!!

[@hardlymovingpro]

Thanks for sharing and glad it worked out for you!

[@los_flores8058]

Thank you for your video!! I was getting a cyl 1 misfire and swapped the coil in a matter of 30 minutes thanks to your video!!! I owe you a beer :)

[@hardlymovingpro]

Good deal! Glad it worked out for you!

[@highenergyworkoutmusic6348]

I know this is an old comment but I am getting the same reading for cylinder 1. Did you still remove the cylinder 3 coil to be able to do cylinder 1 or were you just able to remove and replace cylinder 1 without removing cylinder 3?

[@justinl576]

@@highenergyworkoutmusic6348 Hopefully you figured this out by now but I was able to remove the coil from cylinder 1 without removing 3 just fine. I ended up removing 3 to swap them anyway though.

[@iceyaj3167]

4 dislikes: they don't know what they're doing. thank you for sharing this important video. i've already took all 6 spark plug out of the engine without taking the manifold off. i couldn't do this without your help. it will be hell trying to take out the manifold to gain access to the coils and spark plugs.

[@hardlymovingpro]

Great point!

[@ogopp7834]

If your that incompitent then you shouldn't be working on cars in the first place

[@iceyaj3167]

@@ogopp7834 seem like you're one of them 11 dislikes. im sorry that you didn't know what you're doing.

[@ogopp7834]

After watching the asinineness watching you struggle to take the coil wire off while destroying the coil.and using your special pliers to do the job. When anyone. With a couple sockets a pair of pliers a screw driver and a brain can get that poped off in almost no time. Yes after watching your fuck show unnecessary struggles I thumbs down this video. Because you are literally making this job harder and more difficult than it needs to be putting unnecessary stress on parts because your doing a how to on shit that isn't necessary. Also I have taken mine off and on mutiple times in the last 2 weeks. If you can't remove that in 5 to 10 minutes then you shouldn't be under the hood. You screwing around trying to get the coil out was harder than anything I have had to do to remove it.

[@IamBeyondyouNOT]

@@ogopp7834 thank you.

[@coolwebdude8372]

Only changing coils but watched a couple times how you got #1 and put it back in, and there she went, I think a little bit of that dielectric grease on the outside edge of the rubber helped slide it into the hole. Mine is a 2007 Pathfinder - still runs...Sweet, test drive time! Thank you sir!

[@hardlymovingpro]

Thanks for sharing your experience!

[@danperena2730]

Just change my spark plug today, didn’t have to remove the plenum, everything works fine, thanks for the video, Sir

[@hardlymovingpro]

Excellent and great job!

[@Lou-eye]

I did this to my 2006 xterra a few years ago also, using the right tools like you did, wasn't too hard.

[@hardlymovingpro]

Good for you and thanks for sharing!

[@CH4RLYG777]

Now this video ACTUALLY helped me a lot to get the ignition coil out the first bank 1 spark plug, that twist is the key to gently get it out, thanks so much.

[@hardlymovingpro]

Glad it helped!

[@rontaylor7362]

I did it it works brought the coil at the front and put it back in that direction. I stuck the plugs on 1ft long piece of fuel line to lower them down and get them started. Thanks for sharing.

[@hardlymovingpro]

Good for you!

[@royc1972]

Thank you I've been fighting to get the front two out for a week now.

[@hardlymovingpro]

No problem 👍

[@danielthieme2874]

Just used this video for my pathfinder and it worked great, I was done in an hour. Thanks so much!!

[@hardlymovingpro]

Good for you!

[@jgregg7100]

Thanks for video! Just did mine on 05 xterra with 140k, and pretty sure original spark plugs. Forgot to reattach the vacume hose on the intake when I was done...made for a nice cammy sounds haha

[@hardlymovingpro]

Great news! Glad it worked out for you!

[@BrettJ.]

Working on first plug under the plenum so far so good will repost after I'm done

[@hardlymovingpro]

Sounds good

[@redryder1312]

I just did this, right rear wasn't too bad, I removed the main harness out the way. Front right is the BIGGEST challenge. A cpl of scratches and little bit sore hands, it's done, ready for the next 100K miles.

[@hardlymovingpro]

Nice work!

[@shawnarentscheler8430]

Can not thank you enough for you amazing video. This was the easiest way I have found ever on the internet. Thank you very much for sharing your tips and experience you have learned.

[@hardlymovingpro]

Glad it helped and thanks for your support!

[@jrh4642]

Looks like a massive time saver! I was dreading this until I seen this video.

[@hardlymovingpro]

Yes. It is a time saver!

[@johnmlodynia]

Same deal for Nissan Frontier. 1.5 hr job saved $250 in labor quote from mechanic. Thank you.

[@hardlymovingpro]

Good for you man!

[@adamwilson8559]

Of course I find this video AFTER I removed the plenum to change my plugs. Ha. Great video; thanks for posting and I hope my engine lasts long enough for me to use this method next time :). FWIW - NGK very strongly recommends AGAINST using anti-seize on spark plugs. The laser iridiums (and all other NGK plugs these days) have plating on them that is meant to provide precise friction against the metal of the cylinder head; applying anti-seize can cause the actual force on the threads to be some 20% higher than what the torque wrench indicates because of the reduced friction.

[@hardlymovingpro]

What you said is all true except for American cars with over 100,000 miles with American spark plugs being changed for the first time. I've had experiences with seized plugs that sheared off and had to use a reverse thread bolt extraction tool to get it out. The owner had called the dealer on their recommended remedy and they wanted the cylinder head removed! Owner gave me the green light to use a extraction tool. Also on some Ford F150 V8 engines, the plugs also seize and break apart on removal attempts. So the question is, will NGK pay for parts and labor when your plugs seize and break apart?

[@adamwilson8559]

@@hardlymovingpro Oh I'm sure NGK would get out of it somehow. Thanks for the info!

[@chasa4347]

wow - that is impressive. You didn't even cuss once! I don't know as I could have made this job without a few 4 letter phrases. Thanks for sharing!!!

[@hardlymovingpro]

Glad you liked it and thanks for your post!

[@jamesgaetano7111]

Bro....Thanks so much for this!!! Just did plugs/coils on my 2006 Xterra after getting a P0306 code. 1 & 3 are a bit awkward for sure...ugh Definitely recommend long needle nose, short & long ratchet extensions for this. Tiny hands help too lol

[@hardlymovingpro]

Thanks for sharing and glad the video helped!

[@tylerboyer9523]

just did this over the weekend. to add some key pointers: i used 2 very long screwdrivers to depress the clips under the plenum. a very long screwdriver and a very long pick would be even easier. i also taped my extension combinations together and to the spark plug socket so there was no way it came apart in the spark plug tube. use this time to check the tubes near the firewall for oil leakage in the valve cover spark plug o rings. i took my time and the plenum side took me 1.5 hours.

[@hardlymovingpro]

Hey great story! If anything falls in the spark plug tube, I just use a magnet to pull it out. The important thing about this video, is don't remove the plenum to replace the plugs.

[@zigzag4546]

You the man, this totally worked for me! Great video thanks for posting. patience is key, I also picked up a ratchet, had to cut the one i got down a little all in all took about 1.5 hours.

[@hardlymovingpro]

Hey ... great job ... congrats!

[@rontaylor7362]

I changed the valve timing solinoid assemly on that side without removing the intake manifold. Thanks for making this video. I am going to givebit ago.

[@hardlymovingpro]

Thanks for sharing!

[@39FORTYWATER]

Sir I like you for showing us the difficult it maybe it can be done! Thank you for the video. I have a problem while I am at work. I have been prepare to do the valve cover gaskets and plugs but it was a rainy Saturday and I wanted to do them on this weekend. You know when your Truck is ask for something to be done. I have been leaking oil for awhile, Years! You are the Video of Lifetime!

[@hardlymovingpro]

Thanks for your comments and support!

[@TheInvisibleOne1026]

I can’t thank you enough for this video. This was a daunting task that I kept putting off. But with your video everything went great! Thanks again so much!

[@hardlymovingpro]

Glad it worked out and tell your friends!

[@TheInvisibleOne1026]

Hardly Moving Productions 👍🏼

[@goodbyecalifornia3567]

Thanks for your video, I was in the middle of this job on my frontier and didn’t know I could separate the coil pack in order to take it out. You’ve given me the confidence to try it again as I really didn’t want to remove the manifold, guy at Autozone didn’t sell me gaskets anyway. Thanks again, awesome video.

[@hardlymovingpro]

Glad I could help!

[@ApoetsPoet]

Great video!!! I had a cylinder misfire code and OF COURSE IT HAD TO BE CYLINDER 1🤣 It was still a pain in the ass, but better than removing the plenum. All good...for now

[@hardlymovingpro]

Glad the video helped!

[@eldnahym]

Pulling the plenum was easier than I thought but this looks like a good alternative!

[@hardlymovingpro]

I hear you. Most of these V6 engines (except of Honda) cover up a cylinder bank making it difficult to get to the coil packs/plugs. It comes down to how skillful or creative you are at getting to the plugs.

[@kingofkracovia]

It works. Agree that the #1 on the passenger side is still a big PITA but doable.

[@hardlymovingpro]

Good for you and thanks for sharing!

[@jeremyswift7514]

Thank you so much for making this! Just purchased a Xterra and this will save so much time

[@hardlymovingpro]

Good for you!

[@Ajag4life]

Great video. It was a pain doing it, but you saved me $350.00 labor!!!

[@hardlymovingpro]

Glad it worked out for you!

[@willielittle3078]

Great video sure does beat pulling that plenum off

[@hardlymovingpro]

Thanks! When a customer came to me with a P0300 (random cylinder misfire) code, I knew the first step was to replace the plugs. Watched a few videos and everyone was pulling off the plenum. I figured there had to be a easier way.

[@davechambers9886]

Awesome video! I got a P-0302 and was dreading changing plugs. But, thanks to you, I can get it out so easy. I’ve seen the videos where it’s an all day job having to take half the damn engine apart to change plugs. This is simple.

[@hardlymovingpro]

Thanks! Some criticized this video for not removing the intake plenum

[@danbunch3926]

Why remove it if you don’t have too…

[@sopasaldana]

Thanks for sharing, swivel tools are the real deal, 🙏🏻🙌🏻 helped to save time and the most important, MONEY . 👍🏻

[@hardlymovingpro]

You got that right!

[@fuzzyfish80549]

Thanks for showing us that if we keep the #3 coil out it will give us more room. And if you need even more room you can remove the plate that holds the throttle body steady. It's only four bolts and it opens things up even more. Just keep in mind not to lean on the throttle body.

[@hardlymovingpro]

Thanks for sharing!

[@alexvauxal7075]

Today , I did it in my 07 Frontier......thank you ...thank you , Run perfect now.

[@hardlymovingpro]

Great job!

[@danielburrell723]

Success on my 2010 frontier v-6 4.0. The wobble is key! Replaced plugs to attempt to eliminate the predetonation our trucks have. But boy oh boy 18ft/lbs is alot for a plug. I ended up doing 15-16 which is what the 4 cylinder version wants..

[@hardlymovingpro]

Good for you and thanks for sharing! I don't use a torque wrench most of the time. I apply continuous torque via a 3/8 ratchet wrench until there's no more movement. I've delt with many cars that had their plugs replaced only to discover the plugs had loosened up.

[@ralph39003]

Thank you for the video. It was very helpful. I was able to do my spark plugs without removing the intake.

[@hardlymovingpro]

Good for you and thanks for sharing!

[@rudyrigor4566]

good video, I just did mine 2 days ago.. It was a pain having a big hand and using a regular 10mm open wrench. this video gave me the idea not to take off the plenum.. since all my plenum bolts are kind of rusted..

[@hardlymovingpro]

Glad it helped!

[@BustyWheatThins]

Dielectric grease! You juat solved my problem, the right bank coil thats closest to the cabin would not want to fit all the way into the hole and i was wondering why; idk why my dumbass didn't think to use grease 😂 thanks for the video brotha!

[@BustyWheatThins]

it must be getting stuck on the ceramic part of the plug

[@hardlymovingpro]

Glad I could help!

[@TheHamPimp]

Thank you. This probably saved me an hour by following your lead!

[@hardlymovingpro]

Glad it helped!

[@gospelstewardship6090]

Great work showing how to get this done with the right tools. I just finished changing out the plugs and my check engine light is gone.

[@hardlymovingpro]

Glad it helped!

[@BX0207]

This is tempting me very much to try and attempt to change my spk plugs on my 07 Xterra on my own..

[@hardlymovingpro]

Nothing ventured, nothing gained!

[@SibeDad]

Thanks, made the changing of the spark plugs on my 2012 Xterra a breeze👍👍

[@hardlymovingpro]

You bet and thanks for sharing!

[@BrettJ.]

Done and everything went smooth,thanks for the video!!

[@hardlymovingpro]

Great! Glad it worked out for you!

[@redsteam1]

My man the auto surgeon!!! Thanks very much for doing this video.

[@hardlymovingpro]

Glad you liked it!

[@Winchestersxp]

Great job !! So happy I dont have to remove the intake. Now to find the plugs at a sensible price in Canada !

[@hardlymovingpro]

Glad to be of help. Can you get plugs from Amazon or RockAuto?

[@jdantigua1999]

Thank you Thank you for a great video. No power tools and lots of wobble tools I love your approach as you make it simple by not removing the intake manifold.

[@hardlymovingpro]

You are very welcome and glad it was helpful!

[@evoracing5563]

Great video. Taking off and refitting the intake plenum + plugs takes about an hour. Only downside is, you have to replace rubber seals. Upside of taking it off, you can clean all the accumulated oil and gunk out from it and clean your Throttle body as well. I would recommend removing it every 3rd or so service to clean. So, might as well do this when replacing the plugs as Iridium plugs lasts about 45k to 60k km. Its reall easy to remove it. Your video awesome as it is, I would suggest will be great for only replacing or fault finding a coilpack.

[@hardlymovingpro]

Thanks for your post and critique! You're suggestions are worth thinking about.

[@The1Fist]

Iridium service interval per the manual is 105k miles. I changed mine and they looked almost new out of the package with a slight tint. Unless you get a code, 60k km is only half life of the iridium.

[@brandoperez1313]

Wow man ! This video is awesome . I give up on my truck since I couldn't get those 2 sparkplugs so I was planning on bringing it to the shop. But thanks to you and this video I will try again now with your way to do it . Thanks alot

[@hardlymovingpro]

Glad you found it helpful!

[@nizmo90]

Great video . But u need patience with cylinder 1 which I don't have lol. So took off the plenum but is good to see that it's possible without removing that damn plenum

[@hardlymovingpro]

More power to you if that worked for you!

[@thomasblanco4995]

Brilliant, very helpful. I just successfully accomplished this task.

[@hardlymovingpro]

Good for you and thanks for sharing!

[@timsilva1944]

Great job on the video! You showed and explained everything well. If the naysayers have trouble doing this, they should try working on motorcycles.

[@hardlymovingpro]

Thanks for watching!

[@chrishumpert608]

I haven't change that spark plug since 2011. Only the 5 I could reach. Hallelujah

[@hardlymovingpro]

Good luck with 6!

[@emanuellara1904]

Great vídeo thanks for sharing, already remove all 6 coils following your procedure and yes the is no need to remove the intake manifold. I knew that was crazy to do that just for changing spark plugs 😂

[@hardlymovingpro]

Appreciate your comment! Some would still insist on taking off the plenum ... Guess they like to follow someone's repair guide procedure?

[@mb1636]

Excellent video! I have 07 frontier v6 same engine n able to replica your work !! Thnx !

[@hardlymovingpro]

Glad it helped!

[@bismarkdanquah8146]

Thanks for the video, worked well for me and saved valuable time . The last one was a hustle but I got thru it thanks to your video and the 10mm ratchet trick.

[@hardlymovingpro]

Thanks for the feedback and acknowledgement that this technique does work! To support our channel, give us a thumbs up and subscribe to get notifications of new videos.

[@jeremywethington8545]

Great vid, it's going to save me a headache

[@hardlymovingpro]

Thanks!

[@spicythai2000]

Just did mine. Good information. Thank you.

[@hardlymovingpro]

Good for you and thanks for sharing!

[@chivazopym]

2005 Nissan frontier se. I did it this way and it works. Thanks man.

[@hardlymovingpro]

Right on!

[@wardenwar]

Thanks for this video. You saved me TONS of time and frustration!

[@hardlymovingpro]

Glad it worked out for you!

[@justinl576]

Thank you for this! I had a cylinder 1 misfire and swapped the coils with cylinder 3 which then misfired. Easy fix for once

[@hardlymovingpro]

Glad it helped!

[@ironwill4832]

Grax x el video cada paso que el enseño así c hace y lo de la herramienta baby ratchet de 10 mm es de mucha ayuda sigan estos pasos y van a fallar buen video este tipo no fanfarronea. Grax compa DIOS t bendiga

[@flaviustiberiu442]

the mad lad did it

[@hardlymovingpro]

Good for you!

[@bobjones8378]

That job is such a pain in the ass,I've done it multi[ple times...the coil pack will actually fit between the space on top of the plenum but it has to be angled correctly..excellent videography here

[@hardlymovingpro]

Thanks!

[@colbyscheesy7685]

Great video I watched one where they removed the entire top I was like no Thanks 😂

[@hardlymovingpro]

Thanks for watching!

[@PacketWrangler]

Going to go stare at my 2015 Frontier engine bay and see if I can use this approach. Thanks!

[@hardlymovingpro]

Good luck!

[@keithdonaghy5325]

Excellent and helpful video, thanks. I do not believe you should be using anti seize on that type of plug though. Almost all plug manufacturers recommend against it.

[@hardlymovingpro]

A little won't hurt.

[@GeorgeToft]

My heart sinks every time you drop the 16mm socket into the hole .

[@hardlymovingpro]

No problem getting it out!

[@waymenlawrence2064]

I saw a video where some said don't use anti-seize because it will interfere with grounding spark plug

[@hardlymovingpro]

Not if you apply a very light coat.

[@g.fortin3228]

I like it ...only 1 thing should really blow the debris/dirt from around the holes so you dont brush/knock any in. I know it takes an air hose but most techs or serious DIY's have one handy or at least a can of air..

[@hardlymovingpro]

Yes ... that's a good practice.

[@tylerferrell2959]

thanks a million man for figuring out this hack

[@hardlymovingpro]

Thanks ... still some insist the plenum be removed.

[@andrewziegler2608]

Thank you. I was hopping I can do it this way

[@hardlymovingpro]

Glad I could help

[@gpzjeffrey7974]

Honest to god, it is far easier, especially on cylinders 1, 3, 5, if you simply remove the intake plenum first. The time you spent riding the struggle bus getting the old plugs out and new ones in is more than the time it takes me to remove the intake manifold and put it back. I have dealt with stripped plugs in the past, and never want to be in that situation again. Going at it sideways and with wobblies puts you at risk for stripping plugs.

[@hardlymovingpro]

Thanks for sharing!

[@edgarsanchez5612]

Plzzz follow how he does it because I did it same way and wow that was awesome Lucky I had friends with the tools so I’m happy My is 2012 Nissan frontier pro 4x Also I had no help so it took me 2 hours and my hands and arms are in small side so I was able to get in I recommend u get a small hand/ arm person to go in to pull those ignition coils and to disconnect it Also thanks for showing us how to remove them with out pulling the manifold

[@hardlymovingpro]

Thanks for sharing! Use long nose hose pliers for tight spots for hands.

[@sms9106]

Exactly what I need to do (#1) thanks

[@hardlymovingpro]

Glad to help!

[@K.O.I_WORK]

Ngk spark plugs have a special coating that acts as anti seize and if you use additional anti seize then you’ll over torque them, whether using the 1/2-3/4 turn past snug they say on the box or a torque wrench. Definitely don’t want to mess up someone’s head doing a simple job like this!

[@hardlymovingpro]

Yes ... I'd say NGK and Denso are hands down high quality plugs. Can't say the same about the other American brands (e.g., Motorcraft, AC Delco) that broke apart trying to get them loose. And yes, pre-soaked with penetrating oil. Several times had to use a bolt extraction tool to get the remnants of the plug out of the plug hole.

[@K.O.I_WORK]

Hardly Moving Productions I’ve never had one break on me like that, sounds pretty horrifying.

[@fernandobriseno8164]

I've had pretty good luck with motorcraft

[@hardlymovingpro]

@@fernandobriseno8164 Hands down, Denso and NGK are the best.

[@wellnessotr]

WOW!!! I think I can do this! TY!

[@hardlymovingpro]

Let us know how it turns out!

[@hankreardon6998]

Gonna tackle this tomorrow. Didn't like what I saw when I did the first recon. This will be a great help! What was Nissan thinking?

[@hardlymovingpro]

Thanks. I was wondering that myself!

[@luismujica7917]

YOU SIR ARE A BEAST!!!!!!!!!!!😎😎😎

[@hardlymovingpro]

Thanks!