Cord To Cordless 20V Angle Grinder Conversion

[@gmcm329]

I’ve never seen or heard of this before. Amazing work.

[@hbrestoration]

Thank you very much ^^ have a nice day

[@АнастасияНапилова]

❤❤❤❤❤😂😂😂🎉😢😢😮😮😮😅😅😊тим та смтмчм

[@thelichisdeath]

that motor is rated at 12000 RPM, but it seems like it runs at 400 rpm... something is wrong.... you should cut that L shaped metal bar for less than 5 seconds... never the less, great video, thanks!

[@hbrestoration]

It's not wrong, maybe a more powerful motor will be needed because its speed will be greatly reduced when it reaches the output shaft.

[@elci096]

@@hbrestoration i think this when i see the amperage. Its too low.

[@hbrestoration]

The current you see when I test the motor when it has no load

[@billykulim5202]

There are 2 winding speed for those 775/795 motor. Low speed and highspeed. Looks like your motor are low speed. My grinder conversion with only 16v are faster than that... Something wrong here.

[@hbrestoration]

The motor speed is very high but it decelerates when passing through the pineapple gear@@billykulim5202

[@adraayak]

Very nice transformation. However, you connected the battery directly to the system. What protects the battery from over-discharging? Does the battery have its own protection?

[@hbrestoration]

thank for comment 🥰 you can watch the video i built the battery block, they have self protection circuits

[@RestorationVideo]

Congratulations Very nice!.Top job. Very good recovery. The project conditions are very interesting. You did a great job!! It's great to bring that old machine back to life. Your work has entered the top 10 👋👍🎉 👏 😊 😊 😊.....

[@hbrestoration]

Thank you

[@1islam1]

​@@hbrestoration⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

[@Mahesh_singh1994]

Nice job and u have a brilliant mind ❤

[@hbrestoration]

❤️❤️❤️ thank you

[@MASI_forging]

Nice work dude. Congratulations 😊😊

[@hbrestoration]

Thank you 🥰🥰🥰

[@priyamd4759]

Hi, Nice work and great video. Thanks, Liked and Subscribed - of course! 13:20 For some other project I am looking for a battery holder and not able to get it in India. The generic tool batteries are available online but not the battery holder. Any ideas where i can get these? or where did you get yours? Thanks, Regards,

[@hbrestoration]

you can think of more common mounts or 3d printing. I'm not sure where in India can buy it, I'm not there

[@tramnguyen-xj5hk]

Bạn nên sử dụng động cơ không chổi than cho thiết bị này. Để sử dụng được lâu dài

[@jordano2009]

it was very weak, mine I put a 36v 1,000w motor with support for two batteries in series, it got stronger when it was connected to 220v

[@hbrestoration]

I don't know where you can get a 1000w motor to put in it

[@Mmolokiify]

Nice job you gave me idea of how to restore my burnt grinder..on which devices did you got that motor?

[@hbrestoration]

I bought a new 775 engine

[@sushillad1051]

Rpm very slow you change winding of dc motor after rpm and torque increce, nice project

[@hbrestoration]

I will improve it, thanks for your comment

[@tanurajpoot8822]

Hm

[@tudo9466]

Bạn thật cao tay nghề. Chúc bạn sức khỏe bình an hạnh phúc. Và ra nhiều líp nhé

[@hbrestoration]

thank you ♥ have a nice day ^^

[@MarloMarlo-h6h]

Amazing work my friend 🎉

[@hbrestoration]

♥ thank you

[@Eon_198]

Muy bonito pero se nota que le falta mucha fuerza

[@hbrestoration]

Thank you

[@Simplybestvisions]

Your work is extremely good 🎉 but machine performance is low but try at your best

[@hbrestoration]

thank you❤️

[@marlonalbarracin3845]

nice project, but the motor in kinda weak, good for mini diy👍

[@hbrestoration]

thank youu ♥

[@vuvantuan6932]

Có vẻ như động cơ khá yếu,bạn nên thay nó bằng động cơ Brussels nó sẽ mạnh mẽ và tiết kiệm pin hơn

[@hbrestoration]

yepp, cảm ơn bạn! ^^ có vẻ nó cần 1 động cơ có tốc độ quay lớn hơn. Tôi sẽ cải tiến nó ở nhưng video sau😊

[@chitaole8331]

Trc mìh củg có chế 1 cái trên thân máy mài makita này

[@gearstory1697]

it's so helpful, great video, congratulations 🥰🥰🥰🥰

[@hbrestoration]

Thank you very much 🥰🥰🥰 have a nice day

[@Khoa8994]

Tua chậm quá, nghiên cứu thay motor khác đi fen.

[@hbrestoration]

cảm ơn bạn đã góp ý. Tôi sẽ cải tiến nó ở những video sau

[@449shivakeshavamachani6]

This is also good one to give away to your subscribers sir😊😊😊

[@hbrestoration]

Thank you very much, I am very happy to read your comments.

[@449shivakeshavamachani6]

@@hbrestoration I feel very happy when I get a rc drill machine from you sir to your subscriber,it's not only drill machine i get from you ,but I get a lots of trust from you sir😊😊

[@sebastiaobarros4114]

Very good!!😮

[@hbrestoration]

thank youuu😍😍😍

[@alexandres8846]

using 895 dc motor for high rpm and torque.

[@hbrestoration]

There is also a higher speed 775 motor

[@ashimslife9975]

​@@hbrestoration 895 more torque

[@hbrestoration]

@ashimslife9975 i'll try❤️

[@HENGREPAIR]

Good job

[@hbrestoration]

🥰🥰🥰

[@gilsonfelix3415]

I like that, but as not as fast as it needs to be, isn't it?

[@gilsonfelix3415]

Thanks for carrying

[@hbrestoration]

Thank youu 🥰🥰🥰

[@hbrestoration]

it needs a stronger engine

[@alejandrogutierrez9062]

me preguntaba si se podría hacer lo contrario pero con un atornillador de impacto de batería a cable! 🤔

[@hbrestoration]

Se puede hacer, pero la gente parece preferir la conexión inalámbrica.

[@alejandrogutierrez9062]

@@hbrestoration Si pero la batería sale mas costoso que la misma herramienta! bueno por lo menos donde Vivo es muy caro y difícil de conseguir

[@hbrestoration]

Entonces puedes hacer lo contrario, también sería genial.

[@alejandrogutierrez9062]

@@hbrestoration y vos cómo lo harías? es que esa herramienta (atornillador de impacto) funciona con corriente continua y adaptarla a corriente alterna quemaría la herramienta!

[@hbrestoration]

¿Ya viste el video completo? la respuesta está ahí

[@luatinh5107]

Why don't you upgrade the brushless motor to make it strong? The carbon brushes are very weak and not durable

[@hbrestoration]

I will have another video updating brushless motors

[@gocchiase464]

Làm thì độ li tâm tốt.nhưng vòng quay chưa đủ mạnh

[@hbrestoration]

Tôi sẽ cải tiến nó thêm. Cảm ơn góp ý của bạn !

[@ToktokPhone-u1l]

Ok thanks boss bery bery good

[@hbrestoration]

Thank you^^

[@madhusudhansaini123]

Good job 💯👍👏

[@hbrestoration]

😊 thank youuu

[@yasaralpbaba4537]

Can you send me the link of the charging stand? pls..

[@hbrestoration]

bit.ly/3umGlCj 😊

[@MuhammadKhusaini-f2t]

Excellent..

[@hbrestoration]

thank bro ❤️❤️❤️

[@thongtran72]

con 775 này chạy định mức 0.7A thì hơi đuối

[@nelchan2421]

15:07 don't use solder and copper wire use silicone wire with Female Insulated Spade Wire Connector

[@hbrestoration]

I had the jack but forgot about it ^^ I'll pay attention to it next time 😊

[@art3nfakt]

Un petit peu faible... Sinon l'idée est belle 😊

[@joekao192]

Good job but seem not enough power, u should buy a new one, spend less and better function, and still keep your cord grinder….

[@hbrestoration]

I've also come to realize that; it's better to search for a similar motor with a higher RPM. There's a type of motor like that

[@clickandedit8040]

​@@hbrestoration no. dc motor not that much powerful

[@renanmatos7]

E a velocidade? Somente isso?

[@hbrestoration]

I didn't measure, but it could still spin faster

[@НиколайРепенков]

Редуктор понижает обороты Увеличивая возможную нагрузку Пилить будет но очень долго Идея альтернативная имеет место быть

[@hbrestoration]

Thank you ^^

[@hbrestoration]

🥰🥰🥰

[@battleshippotemkin560]

Обороты электродвигателя слишком маленькие. Мощность так же слишком маленькая. 0,7ампер * 20 вольт=всего 14Ватт. При питании от электрической сети, мощность не менее 700Ватт.

[@hbrestoration]

нет нет, у мотора ток 10-20 ампер, на 0,7 ампер дрова не пилишь 🥹

[@hbrestoration]

Видео стоит посмотреть целиком, я вырезал многие виды железа, чтобы проверить после завершения

[@xmaxkz]

Фольгу пилить пойдет😂

[@eduardopecchio6872]

Será q corta ? 😂😂😂😂😂

[@giuseppezaza6985]

Good work, but motor has not too much power

[@hbrestoration]

Thank you very much. I will try to do better in the next videos

[@NikhilKumar-iw7br]

Good job but power is too low

[@hbrestoration]

Thanks ^^

[@tranviettung4642]

Định làm theo mà thấy khúc cuối cắt yếu quá 😅

[@hbrestoration]

bạn dùng động cơ khỏe hơn và 1 quả pin 36V sẽ quay mạnh hơn

[@tanurajpoot8822]

Good job ❤❤

[@hbrestoration]

Thank iu🥰🥰🥰

[@manimirajlangadi550]

😊😮😮😮

[@hbrestoration]

🤣🥰🥰

[@nelchan2421]

next old makita drill

[@hbrestoration]

I haven't found any drill yet😮‍💨

[@ЖелезнаяЖизнь]

Слишком мало оборотов, редуктор их сильно понижает. Нужен более оборотистый двигатель.

[@hbrestoration]

Кажется более медленным. Я постараюсь улучшить его

[@ЖелезнаяЖизнь]

@@hbrestoration 👍

[@freddybernal9534]

super

[@hbrestoration]

❤️

[@eduardopecchio6872]

O trabalho ficou ótimo mas voce perdeu muita potência, essa máquina só vai servir para pequenos serviços

[@hbrestoration]

♥ Acho que substituir uma bateria por uma de melhor capacidade a tornará mais potente

[@chinaagressor8082]

Была болгарка, а стала дрочилка. Лучшеб ротор со статором поменял на новые.

[@hbrestoration]

Я их заменил, не так уж и плохо

[@Drsollo]

@@hbrestoration дерьмо получилось, а не ушм. тебе дело говорят. Для ушм надо другой мотор ставить.

[@hbrestoration]

Я поставлю более сильный

[@SHOAIB_AWAN]

Grate job ❤

[@hbrestoration]

Thank 🥰🥰🥰

[@mpalaskokkalis1476]

Perfect 👌

[@hbrestoration]

Thank you 🥰🥰🥰

[@dafiraditya7981]

Lebih murah beli jadi

[@aleksije21feb]

👇 Like if Gear Show brought you here!

[@hbrestoration]

🤦‍♂️

[@robotozavr]

Разве поставили не щёточный мотор? Тогда заголовок врёт. Перевели на аккумуляторы, но мотор щёточный.

[@hbrestoration]

Я не понимаю, что ты имеешь в виду. В этом видео рассказывается о процессе переоборудования аккумуляторной болгарки из сетевой в аккумуляторную.

[@avamnepohui7260]

Где там заголовок врет? Английским по белому написано: переделка проводной блогарки в аккумуляторную. Cordless это не brushless)))

[@fahimzain454]

Low rpm not improved 😕

[@hbrestoration]

It still needs further improvement

[@andreipolytov1059]

По валу железным молотком? Это 😢. Вал заклепать три секунды можно.

[@hbrestoration]

😅

[@harshcreations01]

775dc motor ka link bro

[@hbrestoration]

s.net.vn/9DOf

[@Professor_Mori_DIY]

ゆっくり回転なので危険が少ない。

[@hbrestoration]

😅

[@Tẹt_Thị_Muối]

Ngược chiều quay

[@hbrestoration]

quay ngược lại nó văng đá ra mất 😪

[@Tẹt_Thị_Muối]

@@hbrestoration BÁC LÀ NGƯỜI VIỆT NAM AK, E LẠI TƯỞNG NGƯỜI NƯỚC NGOÀI LÀM KÊNH NÀY

[@Tẹt_Thị_Muối]

@@hbrestoration EM THẤY CÁI MẠT SẮT NÓ BẮN VÀO TAY BÁC, VÀ CÁI MẠT DÍNH NÓ CÓ TỪ NÓ DÍNH VÀO MÁY CẮT. NÊN E MỚI BẢO LÀ QUAY NGƯỢC

[@mundodasmaquinas5071]

Muito bom pena que o motor e lento ..

[@hbrestoration]

thank you 😅 I will try to do better 🥰

[@mundodasmaquinas5071]

​@@hbrestorationnão precisa você mostrou que tem talento !

[@hbrestoration]

Ainda tenho muito que melhorar, espero que você lembre de assistir meus vídeos no futuro😅

[@mundodasmaquinas5071]

@@hbrestoration sim sim vou assitir obrigado

[@ЮрийКлик-ъ5э]

Смазка очень густая, она не подходит для такого инструмента, должна быть жидкая, по классификации 0

[@hbrestoration]

да, но кха Док, ты чоа муа Док лоуи лонг хон

[@Naing131]

Need more rpm

[@Zinger37]

Слабый очень двигатель

[@l8icxl]

في فرق بين الاول والثاني الاول قديم وقوي الثاني جديد ضعيف

[@luardj839]

No quedó tan bien al final le falta fuerza para trabajar ....😔

[@hbrestoration]

Try your best, I believe you can do it 😊

[@pcfnokia273]

Mô tơ quay rất yếu, cắt không được sắc ngọt lắm 😂😅

[@RegiPavan]

😎😎😎😎👍👍

[@hbrestoration]

♥♥♥

[@jaouaddahbi4399]

Bonne idée mais le résultat n'est pas bonne

[@hbrestoration]

Je vais essayer de faire mieux dans les vidéos suivantes

[@jailsondasilva223]

Rebarbadora queimou substituir o motor com baterias 😉

[@hbrestoration]

🥰

[@djokodjokovic1663]

low rpm not good

[@hbrestoration]

😅

[@waihingchan2089]

rpm no way😢

[@hbrestoration]

[@AlexMayson1]

обороты в три раза уменшились

[@hbrestoration]

Not that bad, it can't compare to the original engine.

[@MechanicsHome]

wwow

[@hbrestoration]

❤️❤️❤️

[@alkhazalimohamed6058]

It's not good

[@hbrestoration]

I will improve it further

[@ThalaBalawing]

Its important he sucses

[@mynor5959]

Your asss is mine!!!!!

[@mumunewnew]

no it so good

[@hbrestoration]

@mumunewnew thank🥲

[@aldhoariezky9292]

Speed,,power,,its suck

[@lucifersgaming6011]

Still so low rpm

[@hbrestoration]

I will improve it further

[@warwikdallas]

Too few rpm

[@hbrestoration]

😢

[@hariprashanth46]

Cutting speed very slow

[@hbrestoration]

Yepp, cut a little longer

[@Xpdgxkgkhx]

Сколько там оборотов, 500

[@hbrestoration]

Я не мерил, наверное, несколько тысяч выстрелов.

[@อหิงสกะศิริพันธุ์เมือง-ง9ต]

ดี

[@hbrestoration]

🙄

[@daredevil6964]

Rpm kurang kencang

[@hbrestoration]

It can be cut, if you replace it with another battery with higher voltage or a higher speed motor it would be better

[@daredevil6964]

@@hbrestoration lilit ulang motor biar rpm cepat

[@shiroescuadron.1115]

Al cortar se nota que Perdió FUERZA!!!!!!!.......

[@amerhussain8359]

Bro that is not call upgrade but degrade😅

[@hbrestoration]

😂

[@joaozapkkkk2318]

Hey you who are reading, Jesus loves you.

[@hbrestoration]

Many thank ^^ have a nice day

[@akramalishaikh291]

Low rpm

[@hbrestoration]

it needs a larger power source

[@oturanboga6225]

(TÜRKEY)

[@alexsolomko1555]

Обороти слабі , не годиться , хіба полірувати

[@hbrestoration]

Thank you for your comment, it needs further improvement to be stronger

[@adriyantrans145]

Lol, Very long to cut iron😂

[@khangca2597]

Quá yếu cho 1 chiếc máy mài góc

[@hbrestoration]

It needs much more improvement☺ thank you for youer comment

[@ctaasl5033]

Yếu và rất ồn

[@hbrestoration]

🤦‍♂️

[@lucianoelias2747]

🤔🤔🤔 puts assisti o vídeo todo pra vê q está adaptação não presta, ficou muito fraca! Para cortar uma cantoneira demora 2 horas !!! Mas ela assim não deve nem servir como politriz 🤣🤣🤣

[@hbrestoration]

You can replace it with a stronger coin. there's no way to cut it in 2 hours, I think it's much less😅

[@Aleksandr_ECpower]

the power wires will be hushed up very soon, and the power of this grinder is only cut off the claws of the cat, the cheapest grinder of the factory version works many times faster😂😂😂😂

[@hbrestoration]

😅

[@ไม่ตายคงได้พบกัน]

.

[@hbrestoration]

🍎🍏🍋‍🟩🍌

[@KrishnaKumar-ou8ck]

Low performance

[@hbrestoration]

🥲

[@adilsonalvesdeao1294]

showwwwwwwwwwwwwwwww

[@hbrestoration]

♥♥♥

[@Drsollo]

Хрень получилась. Оборотов нормальных нет, тяги нет.

[@hbrestoration]

Пробовал резать с замененным мотором, разрезал толстое железо. Вам стоит посмотреть видео целиком

[@Drsollo]

@@hbrestoration я посмотрел все видео целиком и увидел как этот мотор едва вращает диск под нагрузкой. С таким же успехом можно руками крутить диск и говорить, что нормально пилит.

[@hbrestoration]

Он вращается не быстро, но его крутящего момента достаточно, чтобы разрезать толстое железо.Малая скорость увеличивает время резки. Если вы используете батарею с более высоким напряжением, это даст лучшие результаты. Или может заменить бесщеточный двигатель. Я не думаю, что машина может резать железо, которое можно держать руками.

[@Drsollo]

@@hbrestoration какой там крутящий момент? ты не видишь, что обороты резко падают при нагрузке? нет там ни крутящего момента, ни мощности, ни оборотов. Поставь туда другой мотор.

[@hbrestoration]

Спасибо, буду улучшать

[@addinazimuth2527]

too slow

[@nelchan2421]

😁😆

[@anonymously241]

Very weak motor 🤦‍♂️

[@hbrestoration]

yep need a stronger engine

[@tecnicalvloging]

Bakwas ha kam nhi krta ye bnaya ha mene

[@hbrestoration]

😅

[@tecnicalvloging]

@@hbrestoration dikhao kia bna hoa abhi b ha mere pas ye to moter choti lgai ha aone mene to bari lgai thi power staring wali

[@hbrestoration]

Yes, if you follow suit or invest in a more robust engine. I purchased one that didn't meet my expectations.

[@hasan-lz7rz]

Heloo

[@hbrestoration]

❤️❤️ heluu friend