[HD 1080p] How to Replace Mazda 3 Rear Engine Mount

[@rightcontractingncsf4561]

Please let us know if you end up discovering what the noise turns out to be. Thanks for your videos. It really helps out us 3 owners.

[@OliverPorter92]

Will do! I am 99% sure it is the driver's side mount. That is the most time-consuming to replace. But I have narrowed it down because the PAX side and this one were fine/replaced.

[@rightcontractingncsf4561]

@@OliverPorter92 Good luck, dude. How many km's/miles do you have on your car?

[@OliverPorter92]

​@@rightcontractingncsf4561 109,200 miles. Time for new coolant first, then that other mount, then maybe some bushings that I hear creaking. Love these cars so simple to work on.

[@OliverPorter92]

7 mo update: the minor squeak I hear shifting low gears is not any of the three mounts - I checked / replaced all three and it is still there. It is likely a bolt somewhere that is loose/worn clamp stack/bad bushing somewhere causing a nuisance metal-on-metal clash at that transient condition. I am not worried about it, just a nuisance. Hope this helps!

[@richardpichinino-borden5267]

Ive changed that mount three times and it keeps blowing. And I changed all the other mounts as well and kept having the problem. I’m thinking it’s the piece attached to the mount as well and I can’t find that piece anywhere. I’m pretty sure it’s called the engine mount bracket and that’s bushing is blown as well

[@Combo223]

Hello! great video. I have an issue with my 2010 mazda3 i 2.0L sedan. there is a lot of vibration when i turn the car on. the dash,steering wheel, and side view mirrors will vibrate until the car, at idle, reaches 700rpm. Once that happens the vibration goes away . When I come to a complete stop at a red light or stop sign, the vibration stops once I come to that complete stop and resumes as I accelerate. the vibration stop around 1500 rpm. The motor mounts were replaced about 20K miles ago. the engine doesn't move around. I have tried putting it in neutral when I cold start it,that's when the vibration is more obvious, and the vibration doesn't decrease. the car has no codes including no misfire codes. I recently replaced the spark plugs with new ones, but that didn't affect the vibrations. Thank you!

[@OliverPorter92]

Hi - I am not 100% sure, but if the only major work was the mounts, it could be from non-OEM mounts, torques, or another issue with your vehicle. Sorry this is vague, but I had to isolate a vibe issue to non-OEM mounts recently so that's the first thing that came to my mind that matches your description. Good luck!

[@mazdarene]

What kind of noise or signal does the car to make sure that rear mount is damage?

[@RosesIronmongers]

How do you recommend lining up if the mount has gone and the engine twisted? I cannot see any issues with the other two mounts would this mount cause it to twist so much

[@OliverPorter92]

Not sure but I’d likely combine jacks or an engine lift

[@VishalMech21]

My car vibrate when i put it on reverse gear,which mount do you think will be bad?

[@codyrhatigan7197]

Mine is doing the same thing and I think there is only 2 mounts and the top one you can see so probably the bottom

[@pornorfilrr9170]

check trans mount

[@israellopez361]

Mine does same. Whenever I put it in reverse it vibrates the engine but when I went up to the engine and pushed the engine down while still in reverse it stoped vibrating

[@luis-fe6mj]

So that's the reason the motor moves back and forth do to a Crack or broken engine mount . Pease respond. Should I buy all of the motor mounts.?

[@OliverPorter92]

Thanks for watching. It is one reason. I can't recommend replacing all mounts, you may have to work with a mechanic to isolate the motion to a single mount or other part of the vehicle.

[@MakeItMike]

I have the exact same mount and bracket on my 2011 2.5L I cant find a replacement bushing that goes inside the aluminum bracket anywhere did you have any luck tracking none down??

[@OliverPorter92]

Unfortunately, I cannot find the bushing...sorry - but let me know if you can find it!! Thanks for watching.

[@chadorlando2271]

instaBlaster

[@slow_carsgarage7422]

Have u tried the dealer?

[@GuitarGuy650]

Just buy the bracket. It's like $30

[@daoudaqtash9243]

Is your Mazda 3 a skyactiv model?

[@OliverPorter92]

Thanks for watching! No, this is the base 2.0L VIN-G model.

[@alaazoom8237]

👍🏻👍🏻👍🏻👍🏻

[@alexpolewski1247]

Thanks for not including the torque specs I really appreciate that I just kinda did it till it was snug

[@GuitarGuy650]

Read the description before posting ignorant comments.

[@just_ben1951]

Lol

[@JoubertNYUNDU]

No thanks