Healtech Gear Position Indicator, 2015 R6

  Рет қаралды 4,075

pale rider

pale rider

Күн бұрын

Пікірлер: 25
@jefferyj2995
@jefferyj2995 2 жыл бұрын
I was thinking about getting this gear indicator, but I'm starting to think about buying a $15,000.00 bike with an indicator would be easier. Now I have to figure out how to break the news to my wife. Thanks for sharing.
@palerider6611
@palerider6611 2 жыл бұрын
That's awesome. Just show her this video and say how difficult it is on these old bikes!
@NiteFury2607
@NiteFury2607 8 ай бұрын
2012 R6-This tutorial was on point. I bought an off-brand but it was all exactly the same. The plug-ins are are self-explanatory and I used the Grey wire off the Crankshaft side(black heat shrink) to tap into for the shift indicator(green/black wire). I then ran the 12volt (red/black wire) to the blue/red wire off my integrated brake light. I was able to attach a male bullet connector end and plug and play. Then just program like the instructions say and you are good to go. Pale Rider thanks as this made it that much easier to accomplish.
@palerider6611
@palerider6611 8 ай бұрын
Thanks a bunch for the feedback! Glad it worked out well for you.
@bertobubba
@bertobubba 2 жыл бұрын
thanks for the explanation, it was a huge help that you gave me to make the application on my r6 🙏🙏🙏🙏
@palerider6611
@palerider6611 2 жыл бұрын
you're welcome. I could find about 80% of the explanations through other videos and thought it would be helpful for others to have more of those critical areas documented
@syrupman2292
@syrupman2292 Жыл бұрын
Gteat video!
@palerider6611
@palerider6611 11 ай бұрын
Thanks!
@rrangarb
@rrangarb 2 жыл бұрын
Thanks for great detailed video!
@palerider6611
@palerider6611 2 жыл бұрын
you're welcome. Hope it helps!
@jeremias9043
@jeremias9043 2 жыл бұрын
Great video Thanks!
@palerider6611
@palerider6611 2 жыл бұрын
Glad you liked it!
@jeremias9043
@jeremias9043 2 жыл бұрын
@@palerider6611 absolutely helps me a lot! 👍👍 tanks again!!
@t.nornang1325
@t.nornang1325 2 жыл бұрын
what gauge are the wires you snap into? great job on explaining the tricky part!
@palerider6611
@palerider6611 2 жыл бұрын
Thanks T, I'm not sure of the exact gage, but the wires you snap into for both signal and power are about the same size as those wires that come with the gear indicator. Hope that answers your question
@t.nornang1325
@t.nornang1325 2 жыл бұрын
@@palerider6611 thanks
@Drewrides89
@Drewrides89 Жыл бұрын
If I have an aftermarket harness where would I hook into for the power with the red wire?
@palerider6611
@palerider6611 Жыл бұрын
Not sure. I dont want go give advice that's going to fry your system, but I would think any low power line to brake or tail lights would work.
@Drewrides89
@Drewrides89 Жыл бұрын
@pale rider I tapped into the blinker relay and it worked out, And that was my biggest concern was possibly frying the system
@brucewayne2397
@brucewayne2397 2 жыл бұрын
Hi, was the red wire long enough to reach back to the brake sensor power or did you have to use additional wire? Thanks
@palerider6611
@palerider6611 2 жыл бұрын
Hi Bruce, for me there was sufficient length. However, this is a track bike and I have no brake lights. So I could route the OEM brake/tail light bundle back toward the ECU. If you need to maintain the brake light connector position, you could try to strip back some of the electrical tape far enough so that you can tie in the red power line to the blue OEM line. Or as you suggested, you may need some additional line. I could never find the connector they mention in the instructions that is supposedly closer to the gas tank. Any line that you can find that is active when the ignition is on should work.
@brucewayne2397
@brucewayne2397 2 жыл бұрын
@@palerider6611 thank you for the helpful reply :)
@jackson1463
@jackson1463 2 жыл бұрын
So was it the gray one on the crank?
@palerider6611
@palerider6611 2 жыл бұрын
The two wires coming from the crankshaft position sensor looked light gray and dark gray. I tapped into the pair that had one wire blue and the other gray. From that pair I tapped into the gray wire
@jackson1463
@jackson1463 2 жыл бұрын
@@palerider6611 ok perfect I’m literally doing it right now. The instructions have grey wire in bold but not clear like you said so wanted confirmation before I cut wires. I’m a mechanic so I can’t use scotch locks. lol
龟兔赛跑:好可爱的小乌龟#short #angel #clown
01:00
Super Beauty team
Рет қаралды 97 МЛН
🕊️Valera🕊️
00:34
DO$HIK
Рет қаралды 17 МЛН
Сюрприз для Златы на день рождения
00:10
Victoria Portfolio
Рет қаралды 2,8 МЛН
😜 #aminkavitaminka #aminokka #аминкавитаминка
00:14
Аминка Витаминка
Рет қаралды 2,3 МЛН
Yamaha R6 Shock Upgrade & Swap 2008-16
23:43
Dave Moss Tuning
Рет қаралды 59 М.
Gear indicator install | 07 Yamaha YZF-R6
9:29
Sportbike Everything
Рет қаралды 78 М.
How to Choose Your Axle Gear Ratio
19:15
BleepinJeep
Рет қаралды 1,6 МЛН
Yamaha R6 Diagnostic Mode | Yamaha R6 (eps 3)
5:47
Dradrian97
Рет қаралды 1,5 М.
STOP Crashing Bikes in Corners // Part 1: The LINE
11:15
Moto Control
Рет қаралды 470 М.
Healtech GIpro X-Type G2 FITTED to FZ1-N
13:10
AndyManCam
Рет қаралды 116 М.
Re-Wire Your Whole Damn Car - How To Do It Correctly & Inexpensively
19:10
A Fazer in My Life - Episode 11 - GEAR INDICATOR INSTALL
18:42
Piggy Power
Рет қаралды 28 М.
龟兔赛跑:好可爱的小乌龟#short #angel #clown
01:00
Super Beauty team
Рет қаралды 97 МЛН