This video was hugely helpful. I have the same problem.. The two screws to get it off, I like the jump cut.. because getting that back screw out was a HUGE nightmare. New one on the way..
@gringomds8105 жыл бұрын
that's a 3kj engine also known as a minarelli horizontal. the pump you're using is for a yamaha jog 90cc taiwan version. It is much way better to let your scooter to burn more oil than to let it run lean. but on the other side is that, the leak is not a good sign pf your pumps health.
@gringomds8105 жыл бұрын
try to replace your pump to a autolube or 50cc version rather than a 90cc taiwan version that pumps oil according to the cables opening.
@gringomds8105 жыл бұрын
or prior to that, just empty your 2t tank and disconnect your hose and just mix 25ml of 2T and 1L of gas ratio.
@siTTinLo5 жыл бұрын
Nice vid, explains a lot. Do these small oil pumps create "pressure" to push oil through the line into the carburetor, or does the carburetor create some vacuum "pull" the oil through the pump? Ive removed my pump, and I was spinning the gear using a drill, I got very very little oil drippage. Thank you.
@boyakyat83145 жыл бұрын
since you remove it,change the 2 screw with allen head screw,its much easier to remove once you open it up again..Dont change the whole pump,the only problem with those pump are O-ring in the front,cost here about just a dollar..
@lek24554 жыл бұрын
Is it the seal at 4:02??
@boyakyat83144 жыл бұрын
@@lek2455 yes when u removed that splined pulley you will see the oil cap seal behind it..
@Richfart3 жыл бұрын
I replaced it aswell with an 9.5-16-4 seal works great this far, no more puddle under the scooter.
@sitenpatel6073 жыл бұрын
I have same problem visited mechanic but problem was not solved but these is nice informative video
@nobrimnoyankee39823 жыл бұрын
Mine just smells like crap bro . I got my two stroke moped from the shop and it came with a plastic exhaust cover. Do you reckon that’s why it smells like crap when it’s running ? I’m new to mopeds and motorbikes so I don’t know much. And also it smokes out of the exhaust when idling
@ronmodarres79743 жыл бұрын
Thank you i was not quite sure what was happening with this Zuma that was puchased & I came to clean the filter & there was oil on the bottom of air filter housing & they had clamped a 1- 1/2 inch clear tubing at the bottom of air filer housing & i just didn't see that when I purchased it & ofcourse they didn't say anything either anyhow, how can I purchase this fly wheel puller?
@MrBerenguer673 жыл бұрын
Thks bro 4 your exllente video my piaggio zip 2t smoke a little not much coloure blue what you thing piston rings or samething else thks mate apreciate device cheers
@TheVegasbud5 жыл бұрын
You edited the part where you remove the two screws holding the oil pump on . Most times they are no that easy to remove .
@dannymotovlogs42545 жыл бұрын
Exactly
@gregor.potrebujes2 жыл бұрын
yeah... especially the rear one :) I was trying for an hour but to no avail. I'll leave it for tomorrow...lol
@rogercarmack88673 жыл бұрын
Where did you order that oil pump from I can't find out I need one for my moped
@nathanw5747Ай бұрын
have any videos deleting a super 8 2T? im swapping over to a polini cp19 carb single cable
@gunnarbirgirolafsson89637 жыл бұрын
All this needs to be replaced to replace the oil pump. Is not it enough to release two screws and take the pump straight out?
@Sc00ter3 жыл бұрын
Yah, good luck with that.
@chriskathichloesteven94585 жыл бұрын
Hey buddy how did you bleed your new oil pump
@jaredlecuyer4 жыл бұрын
same thing happened to my morini 2 stroke. I replaced the oil pump but the oil leaks out still, also check valve is new since it is a new carb. Any ideas why?
@tkt93104 жыл бұрын
What kind of bike was it from? Italjet? I have one that has a fm71 head from a formula 50
@mrchilled854 жыл бұрын
and this is why i only run premix on my 1E40QMB i dont trust any 2 stroke oil pump as had one fail on my old tzr 125
@Thor-ps4ke4 жыл бұрын
Where does the top hose on the oil pump lead to and connect?.
@lek24554 жыл бұрын
Did you ever figure it out? wondering the same
@Tizzy_p4 жыл бұрын
@@lek2455 there’s another vid I’ve seen out there with someone doing the oil blacking and it shows you there
@lek24554 жыл бұрын
@@Tizzy_p Nah i figured it out, the oil injector wasnt hooked up at all
@nct94662 жыл бұрын
Why isn’t there any info on set up of oil pump? Is it with or without marks to align at a certain throttle position?
@tortron Жыл бұрын
Best I found was to set the cable tension with the engine running. At idle the cam should sit on the stop, tighten the cable to lift the cam off the stop just as rpms start to climb when twisting the throttle. I. E the stop is set at idle, pump starts opening at throttle opening
@lek24554 жыл бұрын
Where does the smaller line go? the little tube on the top part of the oil pump? is it a breather tube that just hangs off to suck in air?
@adnaltintas3 жыл бұрын
going to the carburetor
@JOKOT015 жыл бұрын
Yeah just remove the whole thing and mix directly in fuel and you will never have to worry about the oil pump :)
@nastynatesscooters98964 жыл бұрын
Jokot when you remove the whole oil pump do you have to plug it or can you just take the oil pumps gear out?
@Tizzy_p4 жыл бұрын
@@nastynatesscooters9896 wondering the same I brought a project and it isn’t there and wondering the same thing
@Cito_Fiytb_6173 жыл бұрын
Same here I dont think I'd leave it open since could probly cause an air leak so I'm gonna remove it and throw some jb weld or putty and let it cure so then I know it's not gonna leak DONE ✅
@gilbertoportillo66503 жыл бұрын
I like your idea!!!
@chrisjones60023 жыл бұрын
The problem with that idea is some motors use the oil pump to lube the bearings too. If you remove it the engine will fail.
@alryley2 Жыл бұрын
Hey can you send me a link for an oil pump. I got a 2005 yamaha zuma/bws 100
@jmac96484 жыл бұрын
What flywheel puller set is that?
@larrykeesee14423 жыл бұрын
HOW. DO I PRIME AAN OIL PUMP ON A KYMCO 50CC ?? RETIRED LARRY IN.INDIANAPOLIS.....
@rock3053053 жыл бұрын
What is the thing called on the left hand side that the throttle line hooked up to not the carb but the other thing
@127EZ4 жыл бұрын
Can i replace the 2t motor with a gy6?
@ajwasp36427 жыл бұрын
Also known as a Minarelli horizontal.
@m90875644 жыл бұрын
All this guy videos just like somebody running after him all his videos less than 2 min all. I never understand any help from him.
@abbasalassadi97024 жыл бұрын
Hello please I want to know the oil kind of yamah scooter 50 cc mixing engine