Make a Refillable Aerosol Spray Can (WD40, PB Blaster, Paint, etc)

How to Make a Refillable Aerosol Spray Can for Paint, WD-40 PB Blaster, etc..
Years ago I made a refillable aerosol spray can for WD-40 because it was so expensive to buy individual spay cans. I found that I could buy a gallon of WD-40 for 1/3 the cost of the 8 oz. spray cans. Over the years my aerosol can stopped working and I decided to make another one.
In this video I show you the steps I take to make a refillable aerosol spray can that saves time and money.
*If this video was a help to you give it a "thumbs up". If you have not already done so, please consider subscribing to this channel.
Disclaimer:
Although I have been following these procedures for many years; I assume no liability for any damage that may occur to any person or property as a result of the information provided in this video. I take necessary precautions (that I am aware of) when working on these projects but that in no way implies or creates any expressed or implied warranty or guarantee of any kind of particular result. Any injury, damage or loss of any kind to anyone or their property or anything related to information in this video is the sole responsibility of the user and not Helping U Online (this video).

[@alfredeinstein8801]

That was a methodical way of DIY to save money. Awesome bro.

[@gjohnston281]

Great video , I will most likely try this , thanks for the info

[@ponchoh.sanchez137]

Hello and have a good day my dear friend and thank you very much for the video you are great and very ingenious and God bless you I always send you a big virtual hug for you and your family and thank you 👍🎉🎉🎉💯

[@beakittelscherz5419]

Fun Project, well done! But you could also buy a chemical resistent small pump bottle, and fill it from your Canister in. I don't even use that anymore. Thin Gear oil mixed with Aceton (50/50) has the exact same effect and is way cheaper!

[@edcrittenden206]

VERY KEWL TOOL!!!! THANX!!!

[@odinhamann3401]

Thanks very much for this idea.

[@helpinguonline]

Thanks for your visit

[@vtxdaryl]

Thanks

[@marvinboggs]

Nice.

[@chrisbartlett6022]

Very entertaining, thanks

[@helpinguonline]

Thanks for your visit

[@oneyaker]

How did you dump the water out with the concave bottom preventing the water from draining? Blowing it out with compressed air would do.

[@davidlovera2879]

I think I've seen this demonstrated on another KZbin* Channel* Video*.. I don't think 🤔 i would try this with an empty can that had been used to spray anything flammable.. But it's also a very good idea, to use for refilling with just compressed air, for blowing through small carburator port holes..💯🤔👍👌😊👨‍🔧🎥🎬⭐⭐⭐⭐✝️🇺🇸

[@VADOC02]

this may be obvious, however how did you remove the rinse water? the bottom of the an is inverted ( concave) and the tube goes to the bottom of the can ?

[@helpinguonline]

I just shook the Can around . You can also blow compressed air through the top Using a tire valve stem

[@voidisyinyangvoidisyinyang885]

how much does the welder cost?

[@earlrissel4454]

Or you go to Harbour Freight and purchase their refillable can and just fill with your favorite product and add air from your air compressor.

[@disturbator]

Solder wont stick to valve in my case. It sticks to can perfectly but no way to get it on the brass valve.... I even polished it....

[@MarshallSmith27]

I am going to do this with kelli. it’s so expensive and I can just buy it not in the spray can

[@klave8511]

The bottom of a pressurized can is shaped to withstand pressure in the can, probably weaker when you damage it by drilling a hole and heating it. Don’t use high pressure.

[@omotolaoyeniyi631]

Actually the integrity is not compromised

[@kbschulze]

Not compromised at all, in fact with the metal cylinder soldered in the center it is likely stronger. To top it off the pressurized can is designed to withstand 3 times the rated pressure as a safety standard.

[@FloydCline]

Zeff as

[@Thumper68]

I just go buy silicone spray for a dollar at dollar store

[@rikstardy]

Sheep?

[@jamesklinckman2363]

If time is money how do you save money? Unless you want to go to your grave with less time and money. I’d rather pay the manufacturer his dividends in his investment of quick automated tooling.

[@duckhunter8387]

The Rewards of working with your hands and being creative are Priceless

[@duckhunter8387]

It's not about saving money. It's about followers and views = Nice Monthly Check $$ from You Tube.

[@Mark-xw2rx]

Man is it necessary to scream ??