Installing Greene Racing camshaft and hearing how it sounds (note) I did not ask for a choppy idle because it's my daily and I leave for work very early in the morning
Пікірлер: 481
@projectevaunit015 жыл бұрын
Holy crap I had to watch that on mute
@venom7626 жыл бұрын
In most shops that I worked for we would have been fired for using abrasive discs on a head surface.
@JK-co6wk6 жыл бұрын
Aluminum heads too. I saw several things in that video that normally would not fly. Like installing the cam bone dry. Assembly Lube is your friend.
@venom7626 жыл бұрын
JK yes sir, there's always time for lube!!
@venom7626 жыл бұрын
JK I don't get me wrong I'm not one to criticize another techs work but that is hackish.
@hoost30566 жыл бұрын
The fact that the truck is running great and hasn't had any issues despite IH beating it mercilessly shows his guy did a good job.
@Eatmydick6666 жыл бұрын
Did he cut out the part where he couldn’t get the cam fully installed because he took a sledge to it?
@indridcold84335 жыл бұрын
Should there be a concern that the camshaft was not greased before being put into the engine?
@devinfraser97954 жыл бұрын
I would say yes lmao
@themanthemyththelegend76714 жыл бұрын
I'm sincerely hoping he knew to wash the pre film off and relube it but the way he was smashing that thing in there those poor cam bearings😄😄😅
@graysgarage21424 жыл бұрын
Yeah I noticed that and it looked like it got stuck until he cut the video. Made me cringe, that boy needed some assembly lube or some molly.
@melissamollohan59923 жыл бұрын
Yes a cam should be greased before installing it shows what they know isn't much
@williamdavis35093 жыл бұрын
Cam lube anyone ❓😬😱
@parkeranderson50743 жыл бұрын
5:57 The viewers: 🙅♂️ 🤷🏼♂️🤦🏻♂️🙋🏼♂️ The installer: 😰😱
@blackmambaram70346 жыл бұрын
Hell yeah, sleeper mode. Exhaust sounds great. Glad your happy with it. Now to get those new track times. Congrats brother!
@IncredibleHemi11116 жыл бұрын
BlackMamba Ram yea sir... Definitely sleeper Jay asked if I wanted a lope tune but I really like sleeper mode and track times are whats most important to me
@blackmambaram70346 жыл бұрын
Incredible Hemi yeah, it will run much better without the lope tune. Timing is pulled on the lope tunes. So slows you down a bit N/A.
@IncredibleHemi11116 жыл бұрын
BlackMamba Ram Really did not know that thanx no lope at all then... There is lil chop but thats what I wanted more sounding like the way it was b4 cam
@blackmambaram70346 жыл бұрын
Incredible Hemi yeah, your good the way you are. Will definitely be in your favor if you like to grudge race. I wanted lope so I chose a more aggressive cam, sacrificed a little torque to get it and just went higher on my stall to compensate the low end loss to get me moving. Lope tunes are just for sound, not at all worth it for a sacrifice in performance. I had a lope tune on the baby cam I had before and it killed my bottom end, went from 1.76 to 1.8s 60' with a dead bite and top end mph didn't pick up any. I only picked up midrange with faster 1/8 mile but same 1/4 in similar weather conditions. Kinda defeats the purpose of the cam install.
@IncredibleHemi11116 жыл бұрын
BlackMamba Ram Yea id be pissed if I didn't pick up any with a cam install
@RTLife6 жыл бұрын
This is getting me pumped... all the pieces are coming in for this.
@IncredibleHemi11116 жыл бұрын
Awesome man it's very exciting time when a cam is ready to be installed
@RTLife6 жыл бұрын
Sounds like we should be good for weekend of Oct 6th - all the parts will def be in. The Cam is the only thing that needs to be plugged in - going to do an intake upgrade down the road. Would he let me film it like this?
@HammerK996 жыл бұрын
I'm jealous of that cordless wrench the mechanic has!
@IncredibleHemi11116 жыл бұрын
HammerK99 yea he had some very nice cordless snap-on tools
@doggieluv786 жыл бұрын
Yeah it's nice. But $500 dollars is a bit much. I have a Milwaukee m12 3\8 cordless wrench it cost $150 dollars.
@ryanpark20492 жыл бұрын
@@doggieluv78 You can pay them off bro
@hellcatredeye-g65826 жыл бұрын
Sounds pretty damn good I did mine before I installed my new engine😊Thanks for the video..A lot of people don’t get to see what us mechanics have to do😏
@IncredibleHemi11116 жыл бұрын
Ken Cook thanx man.. Yea cam install is very intailed
@ronleroy64166 жыл бұрын
Ken Cook i
@18spd4Life2 жыл бұрын
Would’ve been cool if you left in the parts where he struggled with the cam to see how he got it without damaging the cam, I know they can be tricky sometimes so sharing some tips or tricks could be quite helpful
@thebigchungus3222 Жыл бұрын
Did you even watch the video
@18spd4Life Жыл бұрын
Nah I just like to comment based on the title and thumbnail
@347mav36 жыл бұрын
The 60' slowed down because the larger cam moves up the peak torque rpm. Needs a converter to make the most of it.
@codyhowrey46885 жыл бұрын
The really funny thing is that sound just like my truck and I just have a cat back with headers
@gvgnstr26685 жыл бұрын
sounds stock , what a waste .. o wait New Jersey plates that explains the hack job mechanic
@newbornlog27895 жыл бұрын
You went that deep without going for the full Monty heads long tubes intake bro if ripped my 5.7 apart that much everything stock would go bye bye
@chefred1125 жыл бұрын
did you remove mds? I've done quite a few installs and have never removed the intake...just unbolt and hang from the hood, means i didn't have to remove fuel lines too... can't go wrong with a Greene cam..he spec'd a 230/238 cam for my Ram and it's killer..
@billwalker7906 жыл бұрын
Would liked a little instruction NO music
@jacksontodd7919 күн бұрын
You have fuel delivery issue's with pump or have to upgrade your injectors at all
@robertbryan73732 жыл бұрын
All that work.!! No cam lube, or break in procedure..I am curious how many miles u got b4 failure..? 2000..? Sounds like my 2012 jeep grand cherokee with exhaust...dont hear any chop @ all....!! Anyways...just sayin...
@NTfoolhardy5 жыл бұрын
How did you match up the timing Mark's without dropping the oil pump! I am doing a OEM replacement now due to lifter failure. Trying to get out of dropping the oil pan due to I can not right now. The only thing I have left is to get the timing correct.
@Emmanuelwithus4 жыл бұрын
Install was questionable. It sounds GREAT otherwise! Your kid in the candy shop smile says it all man! Here's to the soon-to-be fastest Ram in the nation! Great job and thanks again for the inspiration!
@heathdespain71593 жыл бұрын
Did incredible Hemi have Headers before he put the Cam in? Im asking because i have a Dodge Ram 1500 5.7 L Hemi Rumble Bee with Short Tube Headers and thinking about adding a Cam and kinda wanna get an idea what it might sound like.
@oStirFryo6 жыл бұрын
Ahh.. The source of the powa! r/t life's video of him foolin in your truck sent me :) Sick truck doood
@IncredibleHemi11116 жыл бұрын
Thanx man... It was a great time hes a good guy
@gordon32482 жыл бұрын
I have 2011 dodge ram 1500 5.7l. Installed stage 2 cam no tune yet have an appointment on the 9th to get tune but can hardly drive getting a to rich code. My question did you have same problem also for the 545rfe tans do you know of a good stall to put in there thanks?
@XHikotheproX6 жыл бұрын
Get yourself some shielding and ducting for that intake! It's a hot air intake. The factory setup would be better than that.
@shortbus7945 жыл бұрын
Patrick H 😂🤣 I call it the same thing. Your 110% right. Glad I’m not alone.
@richardhier46815 жыл бұрын
Not having my truck ripped apart.Fuck that !!!
@ls1powered240sx6 жыл бұрын
I was wondering, when you pulled your stock cam out did you notice any abnormal wear? I know it's fairly common issue from what I have been reading? How many miles do you have? Are you or did you upgrade the valve train, rocker, ect.?
@StangMode6 жыл бұрын
Nice 👍 I like that it’s stealth mode
@IncredibleHemi11116 жыл бұрын
EcoBeast thanx man
@mrweeby19614 жыл бұрын
Haven't looked inside the Hemi to get my answer but why pull the heads for a cam swap? Were the lifters changed and they have to come out through the lifter/pushrod holes under the head?
@McDonalds_vesh5 жыл бұрын
Never use a rough discs on two smoothe mating surfaces. If I seen some one do that shit to my motor i would have slapped the back of his head off. All you need is a good scraper
@ET_Don5 жыл бұрын
I wholeheartedly agree. I have a couple of carbide scrapers that work wonders.
@fabianfonseca37813 жыл бұрын
I own the same Ram 1500 brilliant black and was wondering what the link to purchase the camshaft kit ..?
@davidgiles40994 жыл бұрын
You put the stock one back in,, grabbed it on accident lol
@bigaceboogiewoogie19283 жыл бұрын
🤣🤣🤣🤣
@ryanv71955 жыл бұрын
So how did he get the cam in when it got stuck? I think that would probably be the most informative part of the video. What techniques did he use. Did he pull it out a bit and adjust it? Would more lube prevent this?
@750rocketman55 жыл бұрын
He didnt use any lube and i assume he hammered it in.. dont 😂
@Punishment7186 жыл бұрын
Where did you get the Cam installed? I'm looking to get a Greene Racking cam kit installed also. I'm in the process of researching recommended shops in the NY, NJ area.
@tomar6466 жыл бұрын
hey where did you drop the truck ? i got bad lifters and probably my cam needs to be changed im looking for some good shop or mechanic but its hard in PA , i see you have NJ tag maybe is not far from me and guy looks like he know what hes doing , let me know whats the shop name and whats the name of this guy ? thanks
@maldo726 жыл бұрын
Love that there is some room in there to work lol
@IncredibleHemi11116 жыл бұрын
maldo72 Yea it was crazy seeing my man stand in front of the motor
@maldo726 жыл бұрын
Incredible Hemi yes lol what part of Jersey are you from I am also in nj
@Hazmatt34462 жыл бұрын
Nice growl… I was surprised it didn’t lope.
@IncredibleHemi11112 жыл бұрын
I asked for no lope with this cam my new cam lopes good , u can hear in updated videos
@dirrtymurph15915 жыл бұрын
Damn at least spit on it!!
@issort444 жыл бұрын
🤣🤣
@melplishka-se8bf4 жыл бұрын
Ya it did look dry ,maybe picked some scabs on her lol
@WMills-mi7xy4 жыл бұрын
im dying
@Ep1K0nE6 жыл бұрын
Sounds Clean. Can't wait to see your new #'s off the line
@IncredibleHemi11116 жыл бұрын
Ep1K0nE thanx man either can I hoping to get to track soon
@cowboyshotgun80666 жыл бұрын
My hemi run amazing. No tune up needed, except i put a flowmaster outlaw exhaust in it. Omg sounds great
@IncredibleHemi11116 жыл бұрын
They don't need a tune unless u want a lil more power n if u decide to start modding but yes they run great
@DFW1162 жыл бұрын
I have been doing a lot of research on my 5.7 hemi and really want to do a cam but nothing is giving me a straight answer about if I actually have to get my truck turned or not
@gibs36853 жыл бұрын
I am from staten island I have a 2020 ram looking to put a cam in was wondering how much your friend would charge for a job like this thx I appreciate it
@chrisferguson91624 жыл бұрын
How did that kit cost you. I have a 2014 ram 1500 5.7 hemi 4x4 big horn
@joshuas.49676 жыл бұрын
Did you lap your valves when you did this install? My truck is getting Jay's 1.5 V2 Cam early next week, truck has 38,000 miles on it...not sure if the valves needed lapping yet. Thanks.
@jrobles10196 жыл бұрын
Did this cam require a cam phaser kit? Also did you plug in the cylinder de-activate solenoids? I did a cam swap and left those 4 sensors in the valley but I didn’t plug the harness into them. Just wondering?
@bblazeff16 жыл бұрын
Sounds like my 5.7 Hemi. I bought it used with not alot of info but it sure seems like it's got an upgraded cam , I wish I knew for sure.
@ProfessionalByNoMeans6 жыл бұрын
I wanted to hear what he had to say about the mds, also when u came and delete how do u get the check engine light off. I'm sure it comes on. I unplugged my mds 6k miles ago, got 7200 on it now, love the way it drives without that shit. But hate looking at that check engine light.
@DJ_Knite3 жыл бұрын
you need a diablo intune i3 to disable the mds system and no more check engine light, but plug them in before you do the flash.
@Billsor19796 жыл бұрын
Looking to get a cam done on my 300s 5.7. I live right around the corner from where you got yours done. Can you point me in the right direction to get in contact with the mechanic that did yours? Thanks
@mikem44323 жыл бұрын
for the cost of what? 8-9,000$ to have all that work done? could of put a down payment on a Tundra or another more reliable truck.
@austinminton45095 жыл бұрын
I was looking to do this on my 13. Adding performance lifters and a Greene cam. But I'm running 35 inch tires on my truck so how much more performance could I realistically get. I'm not looking for something that'll run quick times at a track I just want the added power for daily use. Is it still worth the money?
@kzwithcc6 жыл бұрын
Needing to replace my cam and lifters in my 2011 ram hemi 5.7. Want to do a performance cam What cam did you install? Did you do lifters? Did you have to do a new program, Did you lose your MDS, so many questions
@reyperez34246 жыл бұрын
corey coombs MDS suxs so yes, he did a MDS delete and I'm positive that he removed MDS with the tune, you'll need all new lifters and new springs are always recommend for peace in mind, the cam is up to your needs , from what I've seen there's only 3 options.
@cad19956 жыл бұрын
I'm liking the sound with cam. Cool video
@IncredibleHemi11116 жыл бұрын
Sixdux Thanx man appreciate it
@rusgts5 жыл бұрын
Did he even put lube on the cam? Took the head off to install springs???? Who is this guys.....????.... btw love the instructions next to him!!!!!!!
@comfortairheatingcoolingllc3 жыл бұрын
Hey nice work. Need to get mine done. Was wondering what's the cost and where in jersey is that mechanic?
@mrsavage1442 жыл бұрын
Is the shop located in New Jersey ? I’m interested in getting a quote thank you
@snowcone753 жыл бұрын
What was your cost for cam and tune and labor? Gonna do mine in January. What cam did you go with from Jay?
@tonyochs30185 жыл бұрын
Dude, this sounds like my 5.7 Grand Cherokee with Muffler delete and that is it.
@Medix-hg3gi6 жыл бұрын
Can't wait to see it FSU down that strip!
@IncredibleHemi11116 жыл бұрын
Reynaldo Ruiz very soon you'll see it run
@Medix-hg3gi6 жыл бұрын
Incredible Hemi Hell Yeah!
@jmata45065 жыл бұрын
Hey dude, what are your cam specs? Looking into a cam from a few companies right now. All three have great street cred and application experience.
@Zo_bomaye4 жыл бұрын
Amazing video, amazing sounding cam.
@gvgnstr26685 жыл бұрын
damn no assembly lube on a new cam !
@ChristianHeider19973 жыл бұрын
I was thinking the same damn thing. Probably would've gone in easier
@frankhubbard3442 жыл бұрын
What did that cost to do, I needed done and don't want to be robbed blind .
@1YouTube_you5 жыл бұрын
Is there no setup for those new springs? I’m a Harley mechanic and we always test and set up the spring height! But I know cars are different so just curious?
@IncredibleHemi11115 жыл бұрын
Yes spring height had to be set
@mmotoxxx796 жыл бұрын
I am looking to do a cam and lifter swap on my 2011 5.7 Big Horn. I'm not looking for high performance racing parts, just need to get the MDS taken out and do the swap. Are there any recommendations on which would be the best non MDS cam and lifters that won't break the bank? Thanks!! And nice video btw!
@IncredibleHemi11116 жыл бұрын
mmotoxxx79 hit up greene racing on facebook best in the buisness for these trucks
@mmotoxxx796 жыл бұрын
Incredible Hemi Thanks! I will check it out.
@coryoglesby21743 жыл бұрын
How bad was the drone on the highway after you cammed it?
@joeseda81024 жыл бұрын
98% of new gearheads OVER CAM their engines and then wonder why only 10 mpg and crummy idle! It's good you made wise decision to keep it "small"if it's your daily driver. What you need for the street is good idle, more torque and quicker acceleration.
@fishermckinzie968810 ай бұрын
What is the cam and the top end set you bought sir mine just dropped on my 2012 in a bind did you have to delete the eco mode shit if so what parts did you get please need help
@michaelboisselle85905 жыл бұрын
Hey I've just seen this video, after putting a ton of money into my vette I'm thinking to do a cam and exhaust for my 17 ram, it's nice to see that you're in nj, I'm in roselle park next to cranford, did your buddy do his ram to and would he do mine?
@ReddbullRam6 жыл бұрын
Hey. I live in south Jersey in hammonton. Where did you get ur cam installed and which one do you have?
@MeMe-ej5hu6 жыл бұрын
I have been waiting for this for 2 weeks
@IncredibleHemi11116 жыл бұрын
Me Me I've been waiting longer than that lol hoping to get some track times on Friday
@MeMe-ej5hu6 жыл бұрын
Incredible Hemi I bet, glad it's finally in, can't wait to see your track runs.
@LEGOCAMARO6 жыл бұрын
Sure would have loved some chop. But understand why can we see the Dino cart see where you pick up on power and torque
@freck93265 жыл бұрын
Hey hey Incredible i just recently had a lifter go to shit and totally screwed my cam.... # 2 if it matters, but i ordered the Modern muscle extreme cam kit with the Obama Delete "MDS" lol. new timing chain new helcat lifters and cam. Just wanting to know if ya think that was the right choice. i know u guys or u know a lot on the hemi and just curious as to if i made the right choice i use yer vids a lot an and think yall are legit. any feedback?? i have done the delete and installed the cam and lifters and about to put the heads and such back together came with all the new bolts,gaskets, timing chain and timing chain guide etc. i did not replace the timing chain because it did not seem that i needed to because everything was tight and still in good condition. if i need down the the line i have either way just wanting to know if ya think i did the right thing no??
@freck93265 жыл бұрын
fck the haters btw lol
@freck93265 жыл бұрын
also sry its an 2009 hemi
@powerstrokecumminsworking25516 жыл бұрын
Looked like a alot of work. Sweet! I'm sure you got some data logging to do for Jay. Lol you can hear me message you at the end of video lol 😂🤣
@IncredibleHemi11116 жыл бұрын
Cumminsworking17 lol yea that was you it was an insane amount of work
@powerstrokecumminsworking25516 жыл бұрын
Incredible Hemi lol, all in good fun tho! I'm glad it went well tho
@mrtoddkable5 жыл бұрын
truck sounds amazing
@IncredibleHemi11115 жыл бұрын
Thank you
@dantheman34266 жыл бұрын
I’m a little late here with this but I read somewhere that you had your cats removed before you put headers on. I’m in the same boat I have full bolt ons and tune in my 8spd. Just wanted to know if it made a noticeable difference or lowered your ET at all. Thank you
@IncredibleHemi11116 жыл бұрын
Daniel Rios I got a Catless ypipe and thd longtube headers done at the same time n yes that was a very big pick up
@bri-manhunter26546 жыл бұрын
I lost a good bit of torque deleting my cats, I added a high flow cat and that helped bring back the torque.
@Eatmydick6666 жыл бұрын
Elevator music would of made this video 200X better
@cjnthn4 жыл бұрын
I'm trying to learn as much as I can about the 5.7 hemi, but I had to turn this off.
@Jeremiahheartly5 жыл бұрын
Lmao Ford tried hitting me with that shopping ram add in the beggining gtfo I'm here for a reason
@713racing12 жыл бұрын
What cam do you recommend for a 5.7 with bolt ons also 100 shot of nitrous
@mauriceware3429 Жыл бұрын
How much a job like that cost on a '04 Dodge ram?
@speedwack6 жыл бұрын
Looks sick with no badges. Exactly what I'm going to do to mine
@IncredibleHemi11116 жыл бұрын
speedwack thanks man yea I love it debadged
@littlebittathisnthatfirear80485 жыл бұрын
@@IncredibleHemi1111 im doing mine now... It sucks
@Chedder2cheesey3 жыл бұрын
Sounds good. Install had some flags but it is what it is
@miguel_garza_official68634 жыл бұрын
What’s the name of the song?
@joshuas.49676 жыл бұрын
Did you have to remove the oil pan for the cam replacement? Thank you for your help.
@IncredibleHemi11116 жыл бұрын
No
@thevally61275 жыл бұрын
I've tried camming my charger RT but no tuner really wanna mess with the Hemi.. that's a cool build tho man
@IncredibleHemi11115 жыл бұрын
Talk to greene racing hell tune any hemi
@joshuas.49676 жыл бұрын
Where did you buy your new head bolts, head gaskets, and timing cover gaskets from?
@IncredibleHemi11116 жыл бұрын
From the dealership just go to parts department but only needed new gaskets
@LuisHerreraunmexicanoenusa20245 жыл бұрын
Where did you buy the camshaft, what is the benefit????
@darrellsyrnyk68756 жыл бұрын
Yo dude your truck sounds awesome. What cam did you use ? I plan on putting a Clay Smith Cam I'm my 2012 1500 with 5.7 Hemi.
@erickmaldonado54304 жыл бұрын
I have 2019 Dodge Ram lone star 4-2 quad cab. I can’t find a site for canned products
@novaguy3836 жыл бұрын
Cool man, good luck at the track!
@IncredibleHemi11116 жыл бұрын
Novaguy383 thanx man hoping to get there as soon as tuning is complete
@Xxtucker51xX3 жыл бұрын
Nobody gonna talk about the dry camshaft going in?
@oscormeyer22835 жыл бұрын
I recently just purchased a ram and I am looking to cam it, I’m not to mechanically inclined so what all has to be done? And should I swap the headers soon after it is camed?
@IncredibleHemi11115 жыл бұрын
I did headers b4 , it doesn't have to be done but I would highly recommend it
@oscormeyer22835 жыл бұрын
Incredible Hemi thanks! Great videos keep the content coming!
@brianmorg2 жыл бұрын
Would have been nice to see how he freed the stuck cam.
@BrownSanta6 жыл бұрын
What shop did the work? As I see we’re both from NJ
@mrpaul69714 жыл бұрын
Holy hell who uses a roloc on a head surface!!!! WOOOOOOF!
@devongreen73086 жыл бұрын
Why would you not change the timing chain and tensioners and oil pump while in there.
@MrC9Oh36 жыл бұрын
right
@corysatterfield75705 жыл бұрын
I wish i could here you explain it. Cuz i have a 3rd gen hemi. 05 ram 1500 hemi sport.
@ag50326 жыл бұрын
Was curious to where you got the work done as I'm in Jersey and have a ram myself. Also what kind of exhaust are you running?
@IncredibleHemi11116 жыл бұрын
Angelo Golino my friend did it on the side at his local dealership n I have MBRP catback exhaust
@Erick-ek7fp4 жыл бұрын
How long was the whole process I’m thinking of installing a Greene racing 2.5 HL v2 cam
@IncredibleHemi11114 жыл бұрын
Took him 8 hours
@billyhope27416 жыл бұрын
Damn man, some voice instruction to go with it would have really helped me out. What in the shit is the point in having music over this when you should be explaining what’s going on the whole time?
@darrellsyrnyk68756 жыл бұрын
Oh yes Borla mufflers the way to go too .yes Borla on my truck .